Shoud the extruder wobble like this ?

Thoughts about Raise3D, 3D printing and making in general.
Monty
Posts: 87
Joined: Wed Oct 19, 2016 6:13 pm

Shoud the extruder wobble like this ?

Postby Monty » Tue Oct 25, 2016 6:38 pm

Should it be like this. It's quite loose
[url]
http://tinypic.com/r/2s993c9/9[/url]

User avatar
Trhuster
Posts: 394
Joined: Tue Mar 22, 2016 6:01 am
Location: Sweden
Contact:

Re: Shoud the extruder wobble like this ?

Postby Trhuster » Tue Oct 25, 2016 7:02 pm

To me it out off spec. I cheering for Raise3d to get successful but they need to source better bearings and rods to avoid this amount off play in the extruder head.

Monty
Posts: 87
Joined: Wed Oct 19, 2016 6:13 pm

Re: Shoud the extruder wobble like this ?

Postby Monty » Tue Oct 25, 2016 7:47 pm

Yer I was looking to see if there was bearing clamps that where loose. That's exactly what it's like.

User avatar
Vicky@Raise3D
Posts: 6482
Joined: Fri Mar 25, 2016 3:54 am

Re: Shoud the extruder wobble like this ?

Postby Vicky@Raise3D » Wed Oct 26, 2016 10:20 am

Please shoot a ticket about this problem to our support system.

Monty
Posts: 87
Joined: Wed Oct 19, 2016 6:13 pm

Re: Shoud the extruder wobble like this ?

Postby Monty » Wed Oct 26, 2016 12:09 pm

OK Have done

sylus
Posts: 108
Joined: Fri Aug 05, 2016 9:47 pm

Re: Shoud the extruder wobble like this ?

Postby sylus » Wed Oct 26, 2016 3:36 pm

same wobbling for mine (ticket done)

jvingaard
Posts: 56
Joined: Sat Nov 12, 2016 10:01 am

Re: Shoud the extruder wobble like this ?

Postby jvingaard » Sat Nov 12, 2016 7:06 pm

Hi,

I just tighten, all the rod screws and that solved the extruder wobble. :-)

User avatar
Vicky@Raise3D
Posts: 6482
Joined: Fri Mar 25, 2016 3:54 am

Re: Shoud the extruder wobble like this ?

Postby Vicky@Raise3D » Mon Nov 14, 2016 5:56 am

Do you mean that you have loose screws which are in below checking list?
X and Y axis check list.pdf
(205.63 KiB) Downloaded 96 times

Monty
Posts: 87
Joined: Wed Oct 19, 2016 6:13 pm

Re: Shoud the extruder wobble like this ?

Postby Monty » Mon Nov 14, 2016 11:19 am

below checking list ?

User avatar
Vicky@Raise3D
Posts: 6482
Joined: Fri Mar 25, 2016 3:54 am

Re: Shoud the extruder wobble like this ?

Postby Vicky@Raise3D » Tue Nov 15, 2016 2:52 am

I want to check with jvingaard whether there on some loose screws on X Y axis would cause extruder wobble.

User avatar
walshlg
Posts: 1350
Joined: Wed Mar 23, 2016 12:01 pm

Re: Shoud the extruder wobble like this ?

Postby walshlg » Tue Nov 15, 2016 5:26 pm

I wonder if this looks worse than it really is since the cold end is so very long it magnifies the apparent movement


Return to “General”

Who is online

Users browsing this forum: No registered users and 2 guests