Page 3 of 6

Re: IdeaMaker feature requests

Posted: Thu May 31, 2018 7:18 pm
by Vicky@Raise3D
Polarbehr wrote:Remaining filament on current roll

Add an option in the HMI that allows us to 'put a new roll' on the printer with 'x' weight. Then when we print a part decrement that weight from the roll. Weight is not 100% accurate but it would help with knowing how much is left on a roll and if the next print is close to using it all up.

Next option if this is implemented could have the printer open up a warning window that there may potentially not be enough filament if remaining on roll is within 10% of what the print requires.


We can see it will be a good feature. But what worry us are currently it will be very hard to achieve the accurate result to do the calculation. Lots of factors will affect the result, such as the estimated filament mount in gcode file is not that accurate, sometime user takes off the filament spool but set printer for loading or unloading, and usually not all the filament spools are starting use from a full spool (you use some and replace another for other use and replace the other half spool back for different tasks).
But anyway, we will try to figure it out, what can we help to achieve this.

Re: IdeaMaker feature requests

Posted: Tue Jun 05, 2018 5:59 pm
by jmel
Ability to set extrusion width...

viewtopic.php?t=1094

Re: IdeaMaker feature requests

Posted: Wed Jun 06, 2018 6:48 am
by Vicky@Raise3D
jmel wrote:Ability to set extrusion width...

viewtopic.php?t=1094


1.png

Re: IdeaMaker feature requests

Posted: Thu Sep 20, 2018 8:04 pm
by DeX
Stl..stl..stl... How about import in IM step, sat, sldprt ?
Useful? Why not..

Re: IdeaMaker feature requests

Posted: Sat May 25, 2019 6:18 am
by DeX
I think the Printer Connect window is too large, has too big fonts. Take a fresh look ! ;-)

Re: IdeaMaker feature requests

Posted: Tue May 28, 2019 11:58 pm
by Vicky@Raise3D
DeX wrote:I think the Printer Connect window is too large, has too big fonts. Take a fresh look ! ;-)


The remote connection window should use the same resolution ratio and the same icons as touchscreen. Or you are looking for a window having less icons, such as only temperatures to show in a small window for quicklook. And expand the window to be a full window.

Re: IdeaMaker feature requests

Posted: Wed May 29, 2019 11:37 am
by DeX
Vicky@Raise3D wrote:
DeX wrote:I think the Printer Connect window is too large, has too big fonts. Take a fresh look ! ;-)


The remote connection window should use the same resolution ratio and the same icons as touchscreen. Or you are looking for a window having less icons, such as only temperatures to show in a small window for quicklook. And expand the window to be a full window.


I meant this, see the pic plz.
When you have a few printers... you do not need to turn the pages a lot =)

Re: IdeaMaker feature requests

Posted: Thu May 30, 2019 4:34 pm
by Vicky@Raise3D
It looks a little to crowded from our opinions.
What about an extra search box to find machine based on machine's name?

Re: IdeaMaker feature requests

Posted: Fri May 31, 2019 11:22 am
by DeX
well, a little crowded yes. but just to show how much free place in that PrinterConnect window.
I haven't a tens of printers to have to search it. phew =)

Another thing if I may:
maybe display the name of the file being printed?
IMG_20190530_130808.jpg

Re: IdeaMaker feature requests

Posted: Fri May 31, 2019 11:41 pm
by Vicky@Raise3D
DeX wrote:well, a little crowded yes. but just to show how much free place in that PrinterConnect window.
I haven't a tens of printers to have to search it. phew =)

Another thing if I may:
maybe display the name of the file being printed?
IMG_20190530_130808.jpg


Will forward your suggestions to developing team.

Re: IdeaMaker feature requests

Posted: Thu Jun 25, 2020 9:48 am
by DeX
I have long wanted to say that with an increase in the view, the control arrows disappear.
arrows1.JPG

closer...
arrows2.JPG

gone!

Re: IdeaMaker feature requests

Posted: Fri Jun 26, 2020 1:37 am
by Vicky@Raise3D
Seems it has been covered by the structures above it. If you rotate the view, you should be able to see it.

Re: IdeaMaker feature requests

Posted: Sun Jun 28, 2020 8:26 pm
by DeX
Vicky@Raise3D wrote:Seems it has been covered by the structures above it. If you rotate the view, you should be able to see it.

or maybe you fix it some how ? =)
this always happens with a large approach to the object. And I need (this large approach ) to more accurately consider where to include the necessary settings.

Re: IdeaMaker feature requests

Posted: Sun Jun 28, 2020 8:28 pm
by DeX
when idle moving to a new printing point, no retract is made and the plastic is smeared on the surface. will it ever be defeated? thank!

Re: IdeaMaker feature requests

Posted: Sun Jun 28, 2020 8:31 pm
by DeX
it would be convenient to see these planes at the bottom of the table. Now through the grid is not visible.
bottomview.PNG

Re: IdeaMaker feature requests

Posted: Sun Jun 28, 2020 8:40 pm
by DeX
a very useful feature in s3d is to look inside both the models and the finished gcode:
crosscection.PNG

Re: IdeaMaker feature requests

Posted: Sun Jun 28, 2020 8:43 pm
by DeX
A very useful feature in s3d is to slice only the necessary sections of the model. Do not wait for the slicing of the entire model, but only a piece. (or you could slice just some process in s3d)
its great! true story. возьмите на карандаш =)

Re: IdeaMaker feature requests

Posted: Tue Jun 30, 2020 1:14 am
by Vicky@Raise3D
DeX wrote:when idle moving to a new printing point, no retract is made and the plastic is smeared on the surface. will it ever be defeated? thank!


Would you like to share the .idea, .gcode and .data files with us to see what is causingthe issue?

Re: IdeaMaker feature requests

Posted: Tue Jun 30, 2020 1:15 am
by Vicky@Raise3D
DeX wrote:it would be convenient to see these planes at the bottom of the table. Now through the grid is not visible.
bottomview.PNG


Thanks for your suggestion. We will add it into future versions.

Re: IdeaMaker feature requests

Posted: Tue Jun 30, 2020 1:15 am
by Vicky@Raise3D
DeX wrote:a very useful feature in s3d is to look inside both the models and the finished gcode:
crosscection.PNG


Thanks for your suggestion. It has been added into developing list.