Page 7 of 7

Re: IdeaMaker feature requests

Posted: Wed Dec 23, 2020 9:21 pm
by clint_45
Hi

I am unsure if this idea have been proposed earlier, couldn't find anything relating to it anyway.

I whould like to have the posibility to change the name of my slicer templates.

Best regards
Clint

Re: IdeaMaker feature requests

Posted: Thu Dec 24, 2020 1:13 am
by Vicky@Raise3D
You can copy the name in Edit. If you are under Advanced, you can go Simple mode from the left bottom corner.

Re: IdeaMaker feature requests

Posted: Sat Dec 26, 2020 7:40 am
by DLS79
A new version of PrusaSlicer will soon be released and it will have a new solid infill pattern that I would very very much like to see in IdeaMaker.

The goal of the new pattern called monotonic is to improve the surface finish/look of top surfaces with holes in them. I have seen some friends test prints, and it plus ironing leads to amazing looking top layers.

You can see it in action here.
https://www.youtube.com/watch?t=40&v=ExX_X0qnRS4

You can read about how its implemented here it here.
https://github.com/prusa3d/PrusaSlicer/ ... 3.0-alpha1

Here is a high resolution image link comparison to a rectilinear top layer.
Image

Re: IdeaMaker feature requests

Posted: Tue Dec 29, 2020 1:16 am
by Vicky@Raise3D
Thanks for your suggestions. We have got similar request before. It has already been added into developing list.

Re: IdeaMaker feature requests

Posted: Sun Jan 03, 2021 7:41 pm
by mastersapo
I suggest the addition of keep out zones / support blocking zones for supports similar to CURA.
https://support.ultimaker.com/hc/en-us/ ... maker-Cura

Re: IdeaMaker feature requests

Posted: Sun Jan 03, 2021 7:54 pm
by Labirynt
mastersapo wrote:I suggest the addition of keep out zones / support blocking zones for supports similar to CURA.
https://support.ultimaker.com/hc/en-us/ ... maker-Cura

what's wrong with actual one?

modifier.PNG


and gcode in preview on this:
modifier_preview.PNG

Re: IdeaMaker feature requests

Posted: Wed Jan 06, 2021 6:39 pm
by DeX
вообще, конечно, не понятно чем там думают создатели слайдеров, если такой момент как равномерное заполнение поверхности лишь с ГОДАМИ приходит в жизнь. это ж после первой печати плоской детали стало понятно!

Re: IdeaMaker feature requests

Posted: Sat Jan 09, 2021 10:23 pm
by leonhart8888
I have a feature request for supports.

It would be great if I could click-drag to delete multiple supports rather than having to click on each pillar individually.

Re: IdeaMaker feature requests

Posted: Tue Jan 12, 2021 1:39 am
by Vicky@Raise3D
Adding Group Select to simplify deleting process is under developing.

Re: IdeaMaker feature requests

Posted: Thu Jan 14, 2021 5:16 pm
by leonhart8888
+1 for monotonic infill, that would be amazing.

Re: IdeaMaker feature requests

Posted: Fri Jan 15, 2021 1:30 am
by Vicky@Raise3D
Thanks for your suggestions!
The feature has been added into developing list.

Re: IdeaMaker feature requests

Posted: Fri Jan 29, 2021 7:43 am
by DeX
АААААААААААА!!!!!!!!!!!
when you open an idea file, you really want the slicing settings to be loaded from it !? Why the hell should I keep it ?!

yeah, I can import them from a file, but this is completely unnecessary / !!!
ааааааааааа

Re: IdeaMaker feature requests

Posted: Thu Feb 11, 2021 3:59 pm
by SelkisFR
Hi Vicky, do you have any plane to have a monotonous infill for top layers to avoid having marks when the nozzle change its direction when meeting a hole. Kinda like PrusaSlicer have. Many thanks for this amazing slicer ;)

Re: IdeaMaker feature requests

Posted: Fri Feb 12, 2021 12:38 am
by Vicky@Raise3D
SelkisFR wrote:Hi Vicky, do you have any plane to have a monotonous infill for top layers to avoid having marks when the nozzle change its direction when meeting a hole. Kinda like PrusaSlicer have. Many thanks for this amazing slicer ;)


Thanks for your suggestions!
The feature has been already added into developing list.

Re: IdeaMaker feature requests

Posted: Thu Feb 25, 2021 9:37 pm
by Pedro Luis
walshlg wrote:5. Add a chime when print is finished


I have solved installing a button via radio:
https://es.aliexpress.com/item/32949087408.html
I have soldered a normally open reed contact to the doorbell pushbutton contacts

Code: Select all

In GCode> End GCode:

G91; Relative Positioning
G1 F3000 E-2; Produces anti-Ooze retraction
G1 Z + 0.5 E-5 X20 Y20 F900.00; Travel 20mm in X and Y
M150 U200; Put the led in green
M104 S0; Turn off the Hot-End
M140 S0; Turn off the bed heater
M107; Turn off fans
G90; Set Absolute positioning
G0 F8000 Y310, Travel to Y310 to activate the chime   <-------
G4 P1000; Sets a 1 second pause  <-------
M150 R0 U0 B0; Turn off the led
G28 X0 Y0; Home XY


When I don't want the chime to sound, I remove a battery.
In the GCode End, I have injected 2 lines,
the first makes the extruder travel to the end on the Y axis (for activate the reed contact)
G0 F8000 Y310
You must find which is the end-point on the Y axis of your printer
Another second line sets a 1 second pause
G4 P1000; Sets a 1 second pause
Then it returns to origin X-Y

Re: IdeaMaker feature requests

Posted: Wed Mar 03, 2021 9:59 pm
by Polar
1. I would love to see something like a calculated value option which Cura has.
For example when changing the default print speed that the ideal combination will be calculated and set by ideamaker.

2. Would love to see the Cura Cross 3D infill pattern in Ideamaker. This infill prints very fast and safes a lot filament compared to standard infill patterns.

3. The place seam on option is not very clear explained. I think Cura has explained this option much better and also I would suggest to add something like their seam corner preference smart hiding option. Whenever possible at the inside of the model prefered.

Re: IdeaMaker feature requests

Posted: Thu Mar 04, 2021 5:24 am
by Vicky@Raise3D
1. The Calculated Value's display will be conflicted with the current tabbed interface. But we are trying to optimize the whole interface, we will take this into consideration.

2. We will add this request into developing list. For the current use, you can try Gyroid or Adaptie Infill.

3. Would you like to advise more information about which part is not explained very well?
Smart Hiding most likely is using reflex corner for most cases as the first option. When selecting Reflex or Convex Corner in ideaMaker, ideaMaker will use reflex croner as the first option too.

Re: IdeaMaker feature requests

Posted: Wed Apr 07, 2021 4:24 am
by Vicky@Raise3D
Thanks for the information. We will add your request into developing list.

Re: IdeaMaker feature requests

Posted: Wed Apr 07, 2021 10:08 am
by Bli
I would like to see a feature where you could choose extruder (left/right) in the Per-layer settings - for instance to make a model with horizontal stripes.
It would also be great to be able to print only outer perimeter with another extruder.

Re: IdeaMaker feature requests

Posted: Thu Apr 08, 2021 2:41 am
by Vicky@Raise3D
ideaMaker doesn't have an option to define which extruder to print outer shells. We can add the request into developing list.