Epcot Center Model

Show off your prints, mods, etc.
User avatar
robpauza
Posts: 70
Joined: Wed Apr 20, 2016 11:50 pm

Epcot Center Model

Postby robpauza » Sat Apr 07, 2018 5:59 pm

Hello everyone,

I thought I would go ahead and share another Raise3D printed custom model. I combined 3D printed elements with some laser cut pieces and I have to say... everything fit together perfectly. I'm continually impressed with the precision of my N2.

This model was created as a favor for a guy at work. It was for a "Trunk or Treat" event during last Halloween and his team's theme was Disney theme parks. His particular part was Epcot of course. He asked me the simple question of "How could he build a sphere?". I took that and went way to far and ended up with a full 3D model and a deadline of about a week and a half. Well... I took a few shortcuts in the end but somehow got it done in time. Here is how it turned out. It was approximately 23" wide x 17" deep x 18" tall. I used eSun PLA+.

Thanks for looking. Sorry if this is a bit pic-heavy.

-Rob



Image

Image

Image

Image

Here's the 3d Model and some renders:
Image

Image

Image

Image

Here's the parts that were 3d printed:
Image

Here's the parts that were laser cut:
Image

I also incorporated some lighting using addressable LEDs and an Arduino microcontroller:
Image

Image

Image

Then, it was time to print:
Image

Image

Image

I laser cut the flat pieces and in Illustrator drew some concrete lines that were laser etched:

Image

Image

Next it was time to paint:
Image

Image

Image

And finished!
Image

User avatar
Vicky@Raise3D
Posts: 5456
Joined: Fri Mar 25, 2016 3:54 am

Re: Epcot Center Model

Postby Vicky@Raise3D » Sun Apr 08, 2018 10:26 am

The details look more than amazing!
What heavy after-processing works are to get the final result!

zemlin
Posts: 415
Joined: Sat Oct 21, 2017 2:02 pm

Re: Epcot Center Model

Postby zemlin » Sun Apr 08, 2018 1:08 pm

uh, yeah. WAY too far! :-) Looks fantastic. Excellent work!

User avatar
robpauza
Posts: 70
Joined: Wed Apr 20, 2016 11:50 pm

Re: Epcot Center Model

Postby robpauza » Sun Apr 08, 2018 2:13 pm

Vicky@Raise3D wrote:The details look more than amazing!
What heavy after-processing works are to get the final result!


Thanks Vicky. Do to time, I didn't use any post work on the prints. Just paint.


zemlin wrote:uh, yeah. WAY too far! :-) Looks fantastic. Excellent work!


Haha... no joke, but it was a fun challenge. Thanks for the compliment.

User avatar
Vicky@Raise3D
Posts: 5456
Joined: Fri Mar 25, 2016 3:54 am

Re: Epcot Center Model

Postby Vicky@Raise3D » Mon Apr 09, 2018 1:46 am

robpauza wrote:
Vicky@Raise3D wrote:The details look more than amazing!
What heavy after-processing works are to get the final result!


Thanks Vicky. Do to time, I didn't use any post work on the prints. Just paint.



I have finished the video of your fantastic bus. The post job looks really cool!

User avatar
robpauza
Posts: 70
Joined: Wed Apr 20, 2016 11:50 pm

Re: Epcot Center Model

Postby robpauza » Mon Apr 09, 2018 2:24 pm

Vicky@Raise3D wrote:
robpauza wrote:
Vicky@Raise3D wrote:The details look more than amazing!
What heavy after-processing works are to get the final result!


Thanks Vicky. Do to time, I didn't use any post work on the prints. Just paint.



I have finished the video of your fantastic bus. The post job looks really cool!



Thanks!

DragonXtreme wrote:Nicely Done


Appreciate it!

Titon
Posts: 35
Joined: Sun Mar 11, 2018 1:31 pm

Re: Epcot Center Model

Postby Titon » Mon Apr 09, 2018 2:53 pm

You do have some serious skills my friend!

User avatar
robpauza
Posts: 70
Joined: Wed Apr 20, 2016 11:50 pm

Re: Epcot Center Model

Postby robpauza » Mon Apr 09, 2018 3:46 pm

Titon wrote:You do have some serious skills my friend!


This is incredibly simple compared to your work, but thanks. -I'm just glad a had a clean wireframe for you to not judge me on. haha :)

Titon
Posts: 35
Joined: Sun Mar 11, 2018 1:31 pm

Re: Epcot Center Model

Postby Titon » Mon Apr 09, 2018 6:55 pm

robpauza wrote:
Titon wrote:You do have some serious skills my friend!


This is incredibly simple compared to your work, but thanks. -I'm just glad a had a clean wireframe for you to not judge me on. haha :)


LOL....well i will get you some wireframes to judge me soon. :)

User avatar
JohnSays
Posts: 687
Joined: Tue Apr 26, 2016 2:42 pm
Location: Saint Petersburg, FL

Re: Epcot Center Model

Postby JohnSays » Sun May 27, 2018 1:24 pm

Wow! You did this as a favor? Just awesomely well done. Very enjoyable to look at. Thank you for sharing so much of the process.
- John

2 Raise3D N2 Duals, Bondtech BMGs, adjustable table, Panucatt SD2224 drivers, run-out sensor, thermal overload protection, Firmware 1.1.9ABH - with Lin_Advance, Palette 2 Pro, Custom E3D hot end and ultra-light carriage and printer head

User avatar
robpauza
Posts: 70
Joined: Wed Apr 20, 2016 11:50 pm

Re: Epcot Center Model

Postby robpauza » Thu Aug 23, 2018 2:44 am

JohnSays wrote:Wow! You did this as a favor? Just awesomely well done. Very enjoyable to look at. Thank you for sharing so much of the process.


Haha, yeah. It also seemed like a good challenge and fun project. Thanks for the comment and praise. I appreciate it.

-Rob

dpla5762
Posts: 2
Joined: Tue Jul 02, 2019 2:27 pm

Re: Epcot Center Model

Postby dpla5762 » Tue Jul 02, 2019 2:29 pm

Hi,

Your model of Spaceship Earth is absolutely the best that I have seen. I was wondering if you would mind sharing the 3D files that you created. I would love to be able to print a version myself. Thanks for the consideration.

Best,
Donald

User avatar
robpauza
Posts: 70
Joined: Wed Apr 20, 2016 11:50 pm

Re: Epcot Center Model

Postby robpauza » Tue Jul 02, 2019 6:33 pm

dpla5762 wrote:Hi,

Your model of Spaceship Earth is absolutely the best that I have seen. I was wondering if you would mind sharing the 3D files that you created. I would love to be able to print a version myself. Thanks for the consideration.

Best,
Donald


Hi Donald,
Thank you sir! And sure. Warning though, I designed the base layers for laser cutting, so I'm not sure how well they will print. I'm still at work, but will get everything together when I get home tonight and I'll DM you a link.
-Rob

User avatar
robpauza
Posts: 70
Joined: Wed Apr 20, 2016 11:50 pm

Re: Epcot Center Model

Postby robpauza » Tue Jul 02, 2019 11:30 pm

robpauza wrote:
dpla5762 wrote:Hi,

Your model of Spaceship Earth is absolutely the best that I have seen. I was wondering if you would mind sharing the 3D files that you created. I would love to be able to print a version myself. Thanks for the consideration.

Best,
Donald


Hi Donald,
Thank you sir! And sure. Warning though, I designed the base layers for laser cutting, so I'm not sure how well they will print. I'm still at work, but will get everything together when I get home tonight and I'll DM you a link.
-Rob


DM Sent. -Rob

dpla5762
Posts: 2
Joined: Tue Jul 02, 2019 2:27 pm

Re: Epcot Center Model

Postby dpla5762 » Sun Jul 14, 2019 2:25 pm

Hi Rob,

Thanks so much for sharing the files! I have found that most people are unwilling to share their work. I really appreciate it! I had a couple questions for you about them though. First, I didn't see the rear middle leg in the files that you sent me. Is there a separate file for that? Second, I was wondering if you used any support material went printing the two dome halves? From the pictures it looks like it is spanning the gap at the top without support. That would be great if that is true. Lastly, I was wondering if you had a link to were you bought the led lights from. I am very new to adding lights to my models so any help with that part of the build is appreciated.

I am working on a pretty detailed model of the Haunted Mansion right now and it is almost done if you are a fan. I will post it on thingiverse when it is ready. If you want to take a look when it is done here is the link to my other models.

https://www.thingiverse.com/donaldplante/designs

Best,
Donald

User avatar
robpauza
Posts: 70
Joined: Wed Apr 20, 2016 11:50 pm

Re: Epcot Center Model

Postby robpauza » Tue Jul 16, 2019 12:34 am

dpla5762 wrote:Hi Rob,

Thanks so much for sharing the files! I have found that most people are unwilling to share their work. I really appreciate it! I had a couple questions for you about them though. First, I didn't see the rear middle leg in the files that you sent me. Is there a separate file for that? Second, I was wondering if you used any support material went printing the two dome halves? From the pictures it looks like it is spanning the gap at the top without support. That would be great if that is true. Lastly, I was wondering if you had a link to were you bought the led lights from. I am very new to adding lights to my models so any help with that part of the build is appreciated.

I am working on a pretty detailed model of the Haunted Mansion right now and it is almost done if you are a fan. I will post it on thingiverse when it is ready. If you want to take a look when it is done here is the link to my other models.

https://www.thingiverse.com/donaldplante/designs

Best,
Donald


You're very welcome, and sorry I forgot that one part. I just sent you a new direct message with a link.

No, I didn't use any support for the dome pieces or anything else. The dome halves droop a bit during the initial inside layers near the top, but quickly fix themselves and make a nice outside shell.

For the one I made here, I used some LED strips that are microcontroller controlled. I specifcically used some APA102 logic ones... but I would recommend using WS2812 if you want to light it that way. there's just 3 solder points (instead of 4) which adds up fast. They come in all different varieties, but here's a sample: https://www.amazon.com/BTF-LIGHTING-Flexible-Individually-Addressable-Non-waterproof/dp/B07BTTY4FL/ref=pd_sbs_60_8?_encoding=UTF8&pd_rd_i=B01CDTECSG&pd_rd_r=ebe6e4bb-a75f-11e9-888e-11c74a3a8f49&pd_rd_w=9HdgY&pd_rd_wg=F96E4&pf_rd_p=588939de-d3f8-42f1-a3d8-d556eae5797d&pf_rd_r=Y8GCZF34R3B2V752554D&refRID=Y8GCZF34R3B2V752554D&th=1D And option two, the WAY easier option, would be to simply use a regular LED strip that you just add power to. There are even some that you can change color and brightness via a remote. I think some even have an option to cycle colors, which would be cool for this. Here's a sample of one of those. https://www.amazon.com/MINGER-Waterproof-Lighting-Controller-Decoration/dp/B079B834PB/ref=sr_1_6?crid=VW9I8Y0ULVLO&keywords=led+strip+color+changing+lights&qid=1563236977&s=hi&sprefix=led+strip+color%2Ctools%2C127&sr=1-6 I personally like the microcontrolled ones just because you can do anything with them, but you do have to do some coding, which may be scary if you've never done it before.

Anyway, I hope this helps. Can't wait to see your Haunted Mansion model. I had a request to make one of those a while back. People should love it. There's apparently not a good one available. Nice job on your other models as well.

-Rob

User avatar
red
Posts: 73
Joined: Tue Jan 22, 2019 7:57 pm

Re: Epcot Center Model

Postby red » Thu Jul 18, 2019 6:03 pm

Fantastic finishing work.

User avatar
robpauza
Posts: 70
Joined: Wed Apr 20, 2016 11:50 pm

Re: Epcot Center Model

Postby robpauza » Thu Jul 18, 2019 6:45 pm

red wrote:Fantastic finishing work.


Thanks so much!


Return to “User's Gallery”

Who is online

Users browsing this forum: No registered users and 2 guests