Extruder stops while moving

Topics around mechanical design, controller and electronics. Mods & hacks welcome.
scienzk
Posts: 20
Joined: Tue Mar 22, 2016 8:16 pm

Extruder stops while moving

Postby scienzk » Fri May 12, 2017 5:23 am

This is my Raise3D N2 +.
There is a problem with the extruder.
I do not know why it stops while moving.
https://www.youtube.com/embed/gEUMa4tra5U

It well greased on rod.
How can I fix this problem??

User avatar
Vicky@Raise3D
Posts: 5742
Joined: Fri Mar 25, 2016 3:54 am

Re: Extruder stops while moving

Postby Vicky@Raise3D » Fri May 12, 2017 10:18 am

If gently hand move the extruder from origin point to center, is that any stuck or not?

scienzk
Posts: 20
Joined: Tue Mar 22, 2016 8:16 pm

Re: Extruder stops while moving

Postby scienzk » Fri May 12, 2017 11:39 am

Vicky@Raise3D wrote:If gently hand move the extruder from origin point to center, is that any stuck or not?


little stuck.
Hard to start to move it while end point

User avatar
walshlg
Posts: 1350
Joined: Wed Mar 23, 2016 12:01 pm

Re: Extruder stops while moving

Postby walshlg » Fri May 12, 2017 12:07 pm

check out the directions for aligning your rods on top they may be a bit skewed after shipping - on mine the pulleys were off

User avatar
Vicky@Raise3D
Posts: 5742
Joined: Fri Mar 25, 2016 3:54 am

Re: Extruder stops while moving

Postby Vicky@Raise3D » Mon May 15, 2017 1:35 am

Here is the checking list.
X and Y axis check list.pdf
(205.63 KiB) Downloaded 132 times

User avatar
Gwen
Posts: 25
Joined: Thu May 04, 2017 9:18 pm

Re: Extruder stops while moving

Postby Gwen » Sun May 21, 2017 6:27 pm

I had a slight noise when printing, so I adjusted the axes following the procedure and now I have the same problem!

However, I move the extruders very easily by hand to prove that the axes are well aligned.

The extruder also moves very easily in the X and Y from the tectile screen but I can no longer bring it back to the origins. It stops in a hell of a noise!

Is there a way to fix this problem quickly?

User avatar
walshlg
Posts: 1350
Joined: Wed Mar 23, 2016 12:01 pm

Re: Extruder stops while moving

Postby walshlg » Sun May 21, 2017 8:09 pm

Gwen, I suggest you send in a help request

User avatar
Vicky@Raise3D
Posts: 5742
Joined: Fri Mar 25, 2016 3:54 am

Re: Extruder stops while moving

Postby Vicky@Raise3D » Mon May 22, 2017 7:37 am

The same suggestion as walshlg. Support system is the quickest way for us to know your problem.
You can start a ticket there and there will have one engineer help follow your case one-to-one.

User avatar
Gwen
Posts: 25
Joined: Thu May 04, 2017 9:18 pm

Re: Extruder stops while moving

Postby Gwen » Mon May 22, 2017 4:00 pm

I did yesterday, I look forward to the response while taking into account the jet lag. In any case it is the same problem as scienzk.

By the way, is my English understandable knowing that I use a lot (uh, all the time actually!) Google Translate?

Thank you Vicky.

User avatar
Vicky@Raise3D
Posts: 5742
Joined: Fri Mar 25, 2016 3:54 am

Re: Extruder stops while moving

Postby Vicky@Raise3D » Tue May 23, 2017 7:35 am

Hi Gwen,

It is ok for me to understand your English. And hope Google can well help you to understand our meaning.

User avatar
Gwen
Posts: 25
Joined: Thu May 04, 2017 9:18 pm

Re: Extruder stops while moving

Postby Gwen » Thu May 25, 2017 8:53 pm

Hi Vicky,

Everything is in order.

Thank you.


Return to “Hardware”

Who is online

Users browsing this forum: No registered users and 2 guests