Page 1 of 1

Get proper harden/steel nozzle for the E2

Posted: Thu Jul 30, 2020 6:58 pm
by FOGD.NO
I am very disapointed with the harden (coated) nozzles that is the only offer from Raise3d to print special filament that need steel nozzle.

I have printed 1/3 of FormFutura CF Petg and I now got a 1mm nozzle instead of 0.4.

Do anyone make nozzles for these machines? I think it is terrible that I bought an "industrial" 3dprinter at high cost and then not able to print something like carbonfibre petg.

The print at the left is the first print I made, and the right is the last.

HardenRaise3dE2Nozzle.jpg
HardenRaise3dE2Nozzle.jpg

Re: Get proper harden/steel nozzle for the E2

Posted: Thu Jul 30, 2020 7:08 pm
by Blue21
You can use also nozzles made for the PRO2.

Re: Get proper harden/steel nozzle for the E2

Posted: Thu Jul 30, 2020 7:12 pm
by FOGD.NO
Blue21 wrote:You can use also nozzles made for the PRO2.



It is the same type.. V3H. Just coated with something and inside it is brass. But does it excist steel nozzles for Pro2?

Re: Get proper harden/steel nozzle for the E2

Posted: Thu Jul 30, 2020 7:33 pm
by Blue21
I didn't found such by my usual supplier, only the Ruby one, very expensive.

Re: Get proper harden/steel nozzle for the E2

Posted: Thu Jul 30, 2020 7:37 pm
by Blue21
I see:
https://www.matterhackers.com/store/l/r ... k/M3U7YTT6
https://filament2print.com/gb/nozzles/1 ... less_steel

But if you really only print CF loaded filament, Ruby nozzle will probably be more cost effective on the long term if you print a lot.

Re: Get proper harden/steel nozzle for the E2

Posted: Thu Jul 30, 2020 8:19 pm
by FOGD.NO
Me and another one found out that MK8 nozzle probably is the same as Raise3d.

I tried a V6 nozzle now and it also fit just with longer thread while total length is same.
So printing with harden V6 nozzle now.

Re: Get proper harden/steel nozzle for the E2

Posted: Thu Jul 30, 2020 8:25 pm
by Blue21
Thanks for the info and hope to hear it worked nicely.

Re: Get proper harden/steel nozzle for the E2

Posted: Fri Jul 31, 2020 9:39 pm
by FOGD.NO
Blue21 wrote:Thanks for the info and hope to hear it worked nicely.


Update. The V6 does work, but not ideal since the top part is flat while the heat break of Raise3d is chamfer at the end. So ideal the heatbreak also need chamfer to match.
The MK8 nozzle is a tiny bit shorter and also flat on top.

Re: Get proper harden/steel nozzle for the E2

Posted: Sat Aug 01, 2020 7:42 am
by Blue21
FOGD.NO wrote:Update. The V6 does work, but not ideal since the top part is flat while the heat break of Raise3d is chamfer at the end. So ideal the heatbreak also need chamfer to match.
The MK8 nozzle is a tiny bit shorter and also flat on top.


Thanks for the update.

Re: Get proper harden/steel nozzle for the E2

Posted: Sun Aug 02, 2020 7:19 pm
by mechovation
Would an official representative of Raise3D care to comment on the nature of the V3H nozzles?

They are listed on the website as Hardened, not Wear Resistant . . . so which is it?

Will most likely need a refund on my uninstalled V3H's

Re: Get proper harden/steel nozzle for the E2

Posted: Tue Aug 04, 2020 11:49 pm
by Vicky@Raise3D
The V3 hardened nozzles are plated brass. According to our experience, they should be more resistant to abrasive filaments. But they will eventually start to wear over time when using abrasive filaments.

Re: Get proper harden/steel nozzle for the E2

Posted: Wed Aug 05, 2020 4:54 am
by FOGD.NO
Vicky@Raise3D wrote:The V3 hardened nozzles are plated brass. According to our experience, they should be more resistant to abrasive filaments. But they will eventually start to wear over time when using abrasive filaments.


So why not make optional steel nozzle like others?

Re: Get proper harden/steel nozzle for the E2

Posted: Thu Aug 06, 2020 1:09 am
by Vicky@Raise3D
We don't have one at this time. Will forward your needs to developing team to see how we can improve in future.

Re: Get proper harden/steel nozzle for the E2

Posted: Thu Aug 06, 2020 3:38 pm
by Allram
Vicky@Raise3D wrote:We don't have one at this time. Will forward your needs to developing team to see how we can improve in future.


Or you can reach out to Slice Engineering and ask if they can make a Vanadium nozzle to the E2 :)

Re: Get proper harden/steel nozzle for the E2

Posted: Thu Aug 06, 2020 8:39 pm
by Vicky@Raise3D
Thanks for your recommendations. Will forward the resources to developing team.