Page 4 of 4

Re: STL Design Shared

Posted: Fri Jun 15, 2018 10:51 pm
by Vicky@Raise3D
Iamkar33m wrote:Raise3D, can we get the STL file you use at the factory for bed level testing? Thanks!

- Kareem


Attached the sliced files for you we using in factory to checking the levelness of Pro2.
Pro2 Leveling Calibration.rar
(43.45 KiB) Downloaded 368 times

Re: STL Design Shared

Posted: Fri Jun 15, 2018 10:51 pm
by Vicky@Raise3D
Jetguy wrote:
Vicky@Raise3D wrote:
Jetguy wrote:Vicky, could you find the power socket cover I just posted the picture of?? I know it's 3D printed so that means somebody has the STL at the factory. Just trying to add safety for those of us with early N2 and N2Plus from the kickstarter. I had used a big piece of heatshrink to make mine safer but there is exposed mains 110 on the backside of the IEC power entry panel between the input and the fuse (the metal bus bar).
Again, earlybird N2 picture under the printer
IMG_0464[1].JPG


Here is the 3D printed version as seen on my new N2Plus
IMG_0463[1].JPG


Here it is. To install it, you need to replace the current two screws to be about M4*16, a little longer than current two.
Power Socket Cover.STL


It could be I overlooked this when searching the master list on the first post here, but could you please edit the page and ensure it's on the front master list of "official" STLs for the printer?


Done.

Re: STL Design Shared

Posted: Fri Jun 22, 2018 12:10 pm
by Hellsbellsidaho
Need the center fan shroud for the Pro2. Is the STL available?

Re: STL Design Shared

Posted: Sat Jun 23, 2018 1:15 am
by Vicky@Raise3D
Hellsbellsidaho wrote:Need the center fan shroud for the Pro2. Is the STL available?


Pro2 Model Cooling Fan Duct.STL
(1.24 MiB) Downloaded 509 times
Pro2 Nozzle Cooling Fan Duct.STL
(2.21 MiB) Downloaded 477 times

Re: STL Design Shared

Posted: Sat Jul 14, 2018 8:57 am
by DeX
Vicky@Raise3D wrote:
Iamkar33m wrote:Raise3D, can we get the STL file you use at the factory for bed level testing? Thanks!

- Kareem


Attached the sliced files for you we using in factory to checking the levelness of Pro2.
Pro2 Leveling Calibration.rar




GREAT! Could we get the same thing for R3D N2 Series? (gcode and stl) Thanks!


(Maybe it could be nice to have these Calibrations Files under the Downloads section of raise3d.com)

Re: STL Design Shared

Posted: Tue Jul 17, 2018 6:11 am
by Vicky@Raise3D
DeX wrote:
Vicky@Raise3D wrote:
Iamkar33m wrote:Raise3D, can we get the STL file you use at the factory for bed level testing? Thanks!

- Kareem


Attached the sliced files for you we using in factory to checking the levelness of Pro2.
Pro2 Leveling Calibration.rar




GREAT! Could we get the same thing for R3D N2 Series? (gcode and stl) Thanks!


(Maybe it could be nice to have these Calibrations Files under the Downloads section of raise3d.com)


Sorry, but I only have .gcode file on hand which is used in factory for calibration the printers.
Actually N series can use the same calibration file as Pro2 series, as the printing volume in X&Y are almost the same.

Re: STL Design Shared

Posted: Tue Jul 17, 2018 9:29 am
by DeX
Vicky, OK then!

Re: STL Design Shared

Posted: Fri Jul 27, 2018 2:28 pm
by Prop-Fiction
By the Pro2 Model cooling the STL. I canĀ“t change the File. Can you push us a open version of it?

Re: STL Design Shared

Posted: Sat Jul 28, 2018 2:17 am
by Vicky@Raise3D
Here you go.
Pro2 Fan Ducts.rar
(90.24 KiB) Downloaded 379 times

Re: STL Design Shared

Posted: Wed Feb 12, 2020 9:44 pm
by PayFactory
Vicky@Raise3D wrote:
Iamkar33m wrote:Raise3D, can we get the STL file you use at the factory for bed level testing? Thanks!

- Kareem


Attached the sliced files for you we using in factory to checking the levelness of Pro2.
Pro2 Leveling Calibration.rar


Hi Vicky, what filament are you using for the Leveling Calibration, just PLA? Thank you!

Re: STL Design Shared

Posted: Wed Feb 12, 2020 10:36 pm
by Vicky@Raise3D
PayFactory wrote:
Vicky@Raise3D wrote:
Iamkar33m wrote:Raise3D, can we get the STL file you use at the factory for bed level testing? Thanks!

- Kareem


Attached the sliced files for you we using in factory to checking the levelness of Pro2.
Pro2 Leveling Calibration.rar


Hi Vicky, what filament are you using for the Leveling Calibration, just PLA? Thank you!


We use PLA.