Raise3D Unpacking Video

Thoughts about Raise3D, 3D printing and making in general.
User avatar
John@Raise3D
Posts: 483
Joined: Fri Feb 26, 2016 8:42 am

Raise3D Unpacking Video

Postby John@Raise3D » Wed Jun 22, 2016 7:43 am

We have uploaded an unpacking video to our Youtube channel.
Please check it out and tell us how you like it!
https://www.youtube.com/watch?v=uhc7Z3O5ROI

User avatar
jmp
Posts: 215
Joined: Mon Mar 21, 2016 12:20 pm

Re: Raise3D Unpacking Video

Postby jmp » Wed Jun 22, 2016 11:04 am

John@Raise3D wrote:We have uploaded an unpacking video to our Youtube channel.
Please check it out and tell us how you like it!
https://www.youtube.com/watch?v=uhc7Z3O5ROI


I wish this had been available 5 months ago :)

While it should be almost exactly the same for the n2+ as the n2 I really would like to see how you recommend getting the n2+ out of the box with its much large size and weight, I really struggled with that.
RL Name: Jason Preuss Thingiverse: JMP Youtube:http://youtube.com/c/patterntoprint Website: http://www.patterntoprint.com

User avatar
2CNK
Posts: 90
Joined: Sat May 21, 2016 5:49 am

Re: Raise3D Unpacking Video

Postby 2CNK » Wed Jun 22, 2016 4:55 pm

Nice video! I like that it's very visual.

The video shows a spacer for adjusting the nozzle space from the bed (8:16).

How thick is that spacer? I didn't see one in my box. What's the spacing set to at the factory?

User avatar
Vicky@Raise3D
Posts: 7121
Joined: Fri Mar 25, 2016 3:54 am

Re: Raise3D Unpacking Video

Postby Vicky@Raise3D » Thu Jun 23, 2016 1:56 am

2CNK wrote:Nice video! I like that it's very visual.

The video shows a spacer for adjusting the nozzle space from the bed (8:16).

How thick is that spacer? I didn't see one in my box. What's the spacing set to at the factory?


It was just a name card in our video. And our suggest distance is 0.2mm. If you think a card is not accurate, you can use a feeler guage to do measurement.

User avatar
Vicky@Raise3D
Posts: 7121
Joined: Fri Mar 25, 2016 3:54 am

Re: Raise3D Unpacking Video

Postby Vicky@Raise3D » Thu Jun 23, 2016 2:17 am

jmp wrote:While it should be almost exactly the same for the n2+ as the n2 I really would like to see how you recommend getting the n2+ out of the box with its much large size and weight, I really struggled with that.


N2+ should have the same steps. Since almost everyone choose to put it on the floor, so you don't need to burden it for the same long distance like N2 from box to table. Only need to remove it from the box, the you get the wheels to move it. If you feel unsure with only two people to hold such a tall printer, you can ask one more person to take a look the front side or the back side in case the printer leans.

Zettlinger
Posts: 412
Joined: Mon Mar 21, 2016 11:48 am
Location: Roosendaal, Netherlands

Re: Raise3D Unpacking Video

Postby Zettlinger » Thu Jun 23, 2016 9:52 am

My N2+ was easily lifted by 2 people especially if you only use it on the floor. it looks heavier then it is (guessing it is about 60KG)


Return to “General”

Who is online

Users browsing this forum: No registered users and 2 guests