N2 Plus, Error: no line number with checksum, last line : 2378

User avatar
easysofts
Posts: 25
Joined: Thu Mar 22, 2018 3:27 pm
Contact:

N2 Plus, Error: no line number with checksum, last line : 2378

Postby easysofts » Tue Jun 04, 2019 9:08 am

N2 Dual Plus with Bondtech dual drive and Filament run-out sensor (printer baught on march 2018)
Tested with ideaMaker 3.3 and 3.4.1
RaiseTouch 1.2.1.428
N2 Plus-dual 1.1.6-rev1

Hi, 2 printers are out of order at same time :
Pro2 shows on RaiseTouch Error card : Error Sensor: T0 (I sent ticket to support in Uk)
and
N2 + shows Error: no line number with checksum, last line : 2378 (no garanty)

Before this state (out of order) These 2 printers failed to print an easy gcode (printed many times on these 2 printers before) : Bondtech gear break filament.

:?: RaiseTouch 1.2.1.428 could it cause this bug on these 2 printers ? Can I downgrade the RaiseTouch ?

Best Regards
Attachments
20190603_220530.jpg
Error: no line number with checksum, last line : 2378
Machines Brand : Raise3D / Wanhao / BCN3D

User avatar
Vicky@Raise3D
Posts: 7117
Joined: Fri Mar 25, 2016 3:54 am

Re: N2 Plus, Error: no line number with checksum, last line : 2378

Postby Vicky@Raise3D » Tue Jun 04, 2019 5:52 pm

We do offer rollback version for RaiseTouch in the following link: https://www.raise3d.com/pages/raise-touch-all-versions
You can test with other versions.

But the Pro2's error looks like temperature feedback issue and N2 Plus's error looks like wrong communication being sent between touchscreen and motion board, unless there is something wrong inside your gcode file. Or both sound more likely related to hardware issue.

User avatar
easysofts
Posts: 25
Joined: Thu Mar 22, 2018 3:27 pm
Contact:

Re: N2 Plus, Error: no line number with checksum, last line : 2378

Postby easysofts » Tue Jun 04, 2019 5:55 pm

I rollback to rollback_1_1_0_1021.raisepack just an hour on the 2 printers.

I'm waiting now if prints fails or not
Machines Brand : Raise3D / Wanhao / BCN3D

Deepak
Posts: 1
Joined: Tue Sep 15, 2020 6:02 am

Re: N2 Plus, Error: no line number with checksum, last line : 2378

Postby Deepak » Tue Sep 15, 2020 6:42 am

Vicky@Raise3D wrote:We do offer rollback version for RaiseTouch in the following link: https://www.raise3d.com/pages/raise-touch-all-versions
You can test with other versions.

But the Pro2's error looks like temperature feedback issue and N2 Plus's error looks like wrong communication being sent between touchscreen and motion board, unless there is something wrong inside your gcode file. Or both sound more likely related to hardware issue.


Hello Vicky,

I have a N2 plus printer. it was working fine until now. Last print stopped in the middle with a error on the board
1. Boar Error: Thermal Runaway, system stopped! Heater _ID:0.
I check all connections and found that ribbon cable was loose. I fixed it and started printing again. But this time the print was paused by filament monitor. I disabled filament monitor. Then I start printing again and every time the print stops with a different error message on the screen. I have attached the screenshots of all the error messages. Please could you help me with the solution as I am a new user.

Thank You
Attachments
IMG_20200914_123459.jpg
IMG_20200914_095520.jpg

User avatar
Vicky@Raise3D
Posts: 7117
Joined: Fri Mar 25, 2016 3:54 am

Re: N2 Plus, Error: no line number with checksum, last line : 2378

Postby Vicky@Raise3D » Wed Sep 16, 2020 6:30 pm

Please try use USB drive to load a most recent RaiseTouch in our download center and let me know whether it can be upgraded succefully or not.


Return to “N Series”

Who is online

Users browsing this forum: No registered users and 1 guest