Search found 412 matches

by Zettlinger
Sun Jun 12, 2016 5:23 pm
Forum: Hardware
Topic: Calibration
Replies: 1
Views: 1143

Re: Calibration

1.5% sounds about right to be linked to the shrinkage of the ABS Under printer settings there is an X Y compensation you can set BUT if it is the shrinking ABS it will mess up your PLA prints (make them larger) If it is a consistent 1.5% i would make a note of the filament and scale it 1.5% for that...
by Zettlinger
Fri Jun 10, 2016 11:56 pm
Forum: Hardware
Topic: Print head shifting during print (?)
Replies: 46
Views: 9133

Re: Print head shifting during print (?)

Not sure if 0,7 mm out of a total print area of 305 mm is not within tolerance, seems a very small variance ( < 0,23% ) Did not measure the distance between the ribs on the belt might be moved over 1 or 2 spaces on the belt. I have not messed with my belt yet (no need to) so for instructions on how ...
by Zettlinger
Thu Jun 09, 2016 11:20 pm
Forum: Hardware
Topic: Print head shifting during print (?)
Replies: 46
Views: 9133

Re: Print head shifting during print (?)

Did you try to print with the left or right extruder ? If your main model was with left then i do not know why it would have set the wipewall since support and raft are correctly set to the left extruder as you would on a single extruder print. To be sure you can disable the wipewall under the tab O...
by Zettlinger
Thu Jun 09, 2016 9:05 pm
Forum: Hardware
Topic: Print head shifting during print (?)
Replies: 46
Views: 9133

Re: Print head shifting during print (?)

the wall around is a wipewall, meaning you set both extruders (prob left support on the other extruder)
by Zettlinger
Thu Jun 09, 2016 7:29 pm
Forum: Hardware
Topic: Hardened All Metal Nozzles
Replies: 14
Views: 4460

Re: Hardened All Metal Nozzles

Any filled pla will be abrasive with a brass nozzle.
by Zettlinger
Thu Jun 09, 2016 9:51 am
Forum: Hardware
Topic: Print head shifting during print (?)
Replies: 46
Views: 9133

Re: Print head shifting during print (?)

Glad you found the source of the noise :) And yes the filament support is correct like this.

I am using Julia's design ,you printed a more fancy one but it will both work :)

Now that you fixed the noise, are your prints ok now ?
by Zettlinger
Tue Jun 07, 2016 10:38 pm
Forum: Feature Requests, Ideas, Wishes
Topic: Printer starting sequence
Replies: 5
Views: 2356

Re: Printer starting sequence

they both get the signal to heat up but you only see the hotend temp rising once that is at the right temp it will show you the heatbed temp You can ofcourse set the temp of the extruder and heatbed manually before sending the print command then you can see both rising at the same time (if you dont ...
by Zettlinger
Tue Jun 07, 2016 11:01 am
Forum: Software
Topic: Simplify3D Offset Issue
Replies: 53
Views: 22657

Re: Simplify3D Offset Issue

tbh i tried S3d and i prefer Ideamaker due to the superior support they print. And at the rate they keep updating and improving the software it will not be long before people start to wonder why they pay 150$ for S3d I do miss the way that S3D can make processes to change settings per model or even ...
by Zettlinger
Tue Jun 07, 2016 10:43 am
Forum: Hardware
Topic: Lubricant?
Replies: 21
Views: 8315

Re: Lubricant?

I have been printing for over 2 months now and still have not needed to lubricate though (as far as i know ;) )
by Zettlinger
Mon Jun 06, 2016 12:13 am
Forum: General
Topic: Unable to get Taulman nylon 645 to stick to BuildTak.
Replies: 11
Views: 5393

Re: Unable to get Taulman nylon 645 to stick to BuildTak.

Just do not forget to clean it before flipping back to the buildtak side :) Depending on the glue it might get messy
by Zettlinger
Mon Jun 06, 2016 12:11 am
Forum: Software
Topic: Dual Head Calibration Q
Replies: 4
Views: 1672

Re: Dual Head Calibration Q

Printer > Printer Settings > Multiple Extruders
by Zettlinger
Sun Jun 05, 2016 4:37 pm
Forum: Software
Topic: Dual Head Calibration Q
Replies: 4
Views: 1672

Re: Dual Head Calibration Q

offset under support is relative to the hole it fills (2mm offset will mean it will leave that space to the sides open)
by Zettlinger
Sun Jun 05, 2016 4:36 pm
Forum: Software
Topic: raft sticking
Replies: 4
Views: 1850

Re: raft sticking

i usually try to have 1 layer height in between raft / support and model and an offset to the sides of about 1 - 2 mm (sometimes a bit more to avoid the support to appear on unwanted places)
by Zettlinger
Sun Jun 05, 2016 12:41 pm
Forum: Software
Topic: Firmware Upgrade
Replies: 8
Views: 3850

Re: Firmware Upgrade

The touchscreen is obvious ofcourse and the motion board is the mainboard in your electricity box (with N2 and N2plus back right side) it controls the motion of the stepper drivers and thus the print head. The touchscreen is the interface and the thing that feeds your motion controller the gcode (if...
by Zettlinger
Sun Jun 05, 2016 12:38 pm
Forum: Hardware
Topic: Printer does not start
Replies: 5
Views: 2205

Re: Printer does not start

If it doesnt start try to do a reset connect the pins below with a paperclip or small pliers (something conductive) :
-raise3d-RYXc-pin.jpg.jpg
by Zettlinger
Sat Jun 04, 2016 3:41 pm
Forum: Hardware
Topic: changing retraction
Replies: 1
Views: 1678

Re: changing retraction

That looks a lot better then the first pictures :)
by Zettlinger
Fri Jun 03, 2016 5:56 pm
Forum: Hardware
Topic: changing retraction
Replies: 1
Views: 1678

Re: changing retraction

avg 1.63 is very bad. What is the min and max diameter ? (if the range is too big having an avg might not help much.. Crap in Means Crap out usually ) I am not sure retraction or the rate is your problem but you could try to incease retraction speed to 30 or so and retracted amount to 1.5 - 2 At fir...
by Zettlinger
Fri Jun 03, 2016 4:34 pm
Forum: General
Topic: Print stuck to plate
Replies: 8
Views: 3373

Re: Print stuck to plate

MSL how i set the gap is this: 1) Gently pull the print head all the way forward , it should then be just beside your glass plate (so if it is set wrong you will not go right through the glass with the nozzle) 2) Hit Z-Home 3) Gently push the head over the glass (eye it to see if you are not too low...
by Zettlinger
Thu Jun 02, 2016 5:53 pm
Forum: Hardware
Topic: orientation of heattblock
Replies: 3
Views: 1398

Re: orientation of heattblock

just make sure the grub screws are on the outside, i think there is only one correct position and the other extruder mirrors it
by Zettlinger
Thu Jun 02, 2016 1:56 pm
Forum: Software
Topic: Settings or Hardware problem?
Replies: 5
Views: 2052

Re: Settings or Hardware problem?

if Odin has a dual extruder he could try the other extruder , if that one prints fine it is not the belts but possibly a clog as Walshlg suggested

Go to advanced search