Search found 470 matches

by Noren
Thu Jan 17, 2019 11:57 am
Forum: N Series
Topic: z-banding/print surface quality
Replies: 14
Views: 1155

Re: z-banding/print surface quality

Check your motor couplers.
Skärmavbild 2019-01-17 kl. 12.56.16.png
by Noren
Thu Jan 17, 2019 10:54 am
Forum: N Series
Topic: Extrusion or something else?
Replies: 4
Views: 340

Re: Extrusion or something else?

Check if your filament is feeding correctly and not slipping.
by Noren
Wed Jan 16, 2019 9:52 am
Forum: Pro2 Series
Topic: 22" tall print stopped printing at 19.75 "s
Replies: 3
Views: 343

Re: 22" tall print stopped printing at 19.75 "s

I have also noticed a large difference in calculated time and actual print time in the latest version. (I have the N1 Dual with the latest version of RaiseTouch, Motionboard and ideamaker. I have the cloud version). I have previously had pretty much bang on calculated and actual print times. But for...
by Noren
Fri Jan 11, 2019 8:36 pm
Forum: N Series
Topic: Extruder 2 Error
Replies: 2
Views: 234

Re: Extruder 2 Error

Do you have the thermal protector installed? These kind of random errors are often due to a break in the flat cable to the extrude board. The gray flat one. If you have one of the N2:s there are often extra cables bundled in the printer that you can use. Cut of the broken bit and pull out a fresh se...
by Noren
Thu Jan 10, 2019 1:52 pm
Forum: N Series
Topic: Load filament width
Replies: 1
Views: 198

Re: Load filament width

Not sure that I understand correctly?. Is the extruded plastic from the nozzle during the load cycle wider than your nozzle diameter?
If it is I would guess that you should change to a new nozzle.
by Noren
Thu Jan 10, 2019 9:47 am
Forum: Printing Settings
Topic: Any luck printing @ 0.1mm / 0.05mm layer thickness?
Replies: 4
Views: 921

Re: Any luck printing @ 0.1mm / 0.05mm layer thickness?

I only briefly tried printing with S3D on my Raise3D. But I had a hard time getting any good results. And I think that the results on the Raise3D machines with IdeaMaker is on par or better than S3D. I have also successfully printed .1 and .05 with the default High Quality templates. Correct distanc...
by Noren
Tue Jan 08, 2019 10:07 am
Forum: Pro2 Series
Topic: Cables touching Belts
Replies: 5
Views: 488

Re: Cables touching Belts

The same on my N1.
by Noren
Sat Dec 29, 2018 6:26 pm
Forum: N Series
Topic: Bondtech Dual Upgrade problem
Replies: 5
Views: 579

Re: Bondtech Dual Upgrade problem

Bad top surface is often due to the nozzle to close to the bed or overextrusion. Or a combination.
by Noren
Sat Dec 29, 2018 6:25 pm
Forum: Software
Topic: API?
Replies: 22
Views: 3563

Re: API?

jetdillo wrote:Is this available for the N2 series or just the Pro ?
I have an N2 Plus and that port isn't active on my machine. I have TouchPanel firmware version 1.1.0.1021.


You need to install the Raise Touch Cloud firmware I think.
by Noren
Fri Dec 07, 2018 11:59 am
Forum: Printing Settings
Topic: Now Support
Replies: 2
Views: 326

Re: Now Support

Chrigi78 wrote:Dear all

now we have a intressting problem

if we say no support an Make no Support the system make self support on diffrent points ???

how we can switch off this ???


Check that you have "none" selected in this menu:
Skärmavbild 2018-12-07 kl. 12.58.22.png
by Noren
Mon Dec 03, 2018 10:34 pm
Forum: Software
Topic: IM Graphic Box showing up in new release
Replies: 3
Views: 363

Re: IM Graphic Box showing up in new release

DragonXtreme wrote:Thanks Noren, unfortunately my account was deleted and all my post along with it. So now I have to make a couple more post to get back to allowed status without being monitored. Vicky gave no reason for the deletion except that it was. :(


Sorry to Hear. :(
by Noren
Sun Dec 02, 2018 11:58 am
Forum: Pro2 Series
Topic: New Firmware Settings - Which is Master?
Replies: 5
Views: 557

Re: New Firmware Settings - Which is Master?

The sethings in the printer is used if you haven’t checked the acceleration and jerk check boxes in ideamaker. In that case those are used. That’s my understanding.
by Noren
Sat Nov 17, 2018 5:27 pm
Forum: General
Topic: Shrinkage in Circular object
Replies: 1
Views: 360

Re: Shrinkage in Circular object

Additional cooling could help some. Also lower the distance between layer and support. And print with dense support layers.
by Noren
Mon Nov 12, 2018 6:10 pm
Forum: Hardware
Topic: what cameras work on n 2plus
Replies: 3
Views: 506

Re: what cameras work on n 2plus

Realt don’t know. Haven’t pulled images to the computer yet. And I don’t have the standard Raise3D camera to compare to.
by Noren
Mon Nov 12, 2018 3:47 pm
Forum: Hardware
Topic: what cameras work on n 2plus
Replies: 3
Views: 506

Re: what cameras work on n 2plus

On my N1 the Logitech C922 camera works.
by Noren
Mon Nov 12, 2018 3:46 pm
Forum: Software
Topic: IM Graphic Box showing up in new release
Replies: 3
Views: 363

Re: IM Graphic Box showing up in new release

Uncheck "Show extruders printing range".

Skärmavbild 2018-11-12 kl. 16.45.21.png
by Noren
Thu Oct 25, 2018 10:18 pm
Forum: Printing Settings
Topic: Poor quality top surface
Replies: 2
Views: 388

Re: Poor quality top surface

Try lowering the flow rate 10% and see if it makes a difference.
by Noren
Wed Oct 24, 2018 2:54 pm
Forum: Printing Settings
Topic: What does density affect?
Replies: 1
Views: 289

What does density affect?

What effect does changing the filament density have in the finished print? Does it affect anything more than the estimated print time? Does it affect the print?
by Noren
Thu Oct 18, 2018 7:44 am
Forum: N Series
Topic: N1 Cable Chain Mod
Replies: 5
Views: 606

Re: N1 Cable Chain Mod

Really nice. My only negative comment on this: it looks like it sags a little att the start and the beginning. Is it possible to stiffen it up a little to counteract the sagging?
by Noren
Wed Oct 10, 2018 7:37 pm
Forum: Software
Topic: Reslice without closing settings window. Feature request.
Replies: 3
Views: 465

Reslice without closing settings window. Feature request.

I have been experimenting with settings and I have gotten really fed up with how the slicing settings work.
I really would like to have the settings window remain open when changing things and realising. Jumping in and out of the advanced settings window is a real pita.
:(

Go to advanced search