Search found 31 matches

by claytony565
Fri Jun 15, 2018 6:00 pm
Forum: General
Topic: Calibration PRO 2
Replies: 7
Views: 3119

Re: Calibration PRO 2

Bed leveling is pretty much the same, I think there are a few less points of contact and some of the bolts seem to be more secure. The bed plate is removable though so that is nice. And they do ship the Pro2 models with a calibration print on the plate which is actually pretty reassuring. Have been ...
by claytony565
Thu Jun 14, 2018 6:18 pm
Forum: General
Topic: Raise3D Pro2 initial impression
Replies: 11
Views: 3483

Re: Raise3D Pro2 initial impression

Have you had any problems so far? I am having issues with heating that are eerily similar to the N series printer ribbon cable fiasco. I know they do to use the same cable but I am experiencing the same erratic temperature problems, except this time I get no error just burnt filament! If you could,...
by claytony565
Thu Jun 14, 2018 3:53 pm
Forum: General
Topic: Raise3D Pro2 initial impression
Replies: 11
Views: 3483

Re: Raise3D Pro2 initial impression

Have you had any problems so far? I am having issues with heating that are eerily similar to the N series printer ribbon cable fiasco. I know they do to use the same cable but I am experiencing the same erratic temperature problems, except this time I get no error just burnt filament!
by claytony565
Thu Jun 14, 2018 2:28 pm
Forum: User's Gallery
Topic: First Month of Printing
Replies: 4
Views: 1421

Re: First Month of Printing

Yes, just wanted to see if it was possible. I also scaled the entire thing down so the hole isn't necessarily fit for a standard fastener. I'm new with the Raise3d N2 plus printer (1 week of practice) and I'd really like to know what parameters did you use to get the bolt-nut system working. I have...
by claytony565
Fri Jun 08, 2018 1:14 pm
Forum: Hardware
Topic: Filament Run-out Sensor Add-on
Replies: 89
Views: 15064

Re: Filament Run-out Sensor Add-on

UPDATE: I plugged it in to the MCB upside down like a doofus. In order to best explain to others to prevent the mistake. I think you are saying you flipped the EXP3 connector with the red and back wires. It is not "keyed" and can be flipped around and still plug in- but when doing so- no ...
by claytony565
Thu Jun 07, 2018 6:05 pm
Forum: Hardware
Topic: Filament Run-out Sensor Add-on
Replies: 89
Views: 15064

Re: Filament Run-out Sensor Add-on

UPDATE: I plugged it in to the MCB upside down like a doofus.
by claytony565
Tue Jun 05, 2018 4:12 pm
Forum: Hardware
Topic: Filament Run-out Sensor Add-on
Replies: 89
Views: 15064

Re: Filament Run-out Sensor Add-on

Well thought I would go ahead and chime in on this thread here. I have installed the filament sensor on our N2 Plus at work and it does absolutely nothing when filament runs out. I have even started a print with no filament and it starts like normal and ghost prints. Pretty disappointed in this &qu...
by claytony565
Mon Jun 04, 2018 9:27 pm
Forum: General
Topic: Just Released N2 Pro
Replies: 124
Views: 40550

Re: Just Released N2 Pro

Last, I'm tempted to call you out on speeds. If the basic gantry mechanics stayed the same, and the change here is electronics and firmware, yes, you may have sent gcode at 80mm/s perimeter. Like I've said hundreds of times, that's like a speed limit sign in both the max speed and desired speed- bu...
by claytony565
Fri Jun 01, 2018 3:26 pm
Forum: User's Gallery
Topic: First Month of Printing
Replies: 4
Views: 1421

Re: First Month of Printing

Yes, just wanted to see if it was possible. I also scaled the entire thing down so the hole isn't necessarily fit for a standard fastener.
by claytony565
Fri Jun 01, 2018 2:19 pm
Forum: Hardware
Topic: Filament Run-out Sensor Add-on
Replies: 89
Views: 15064

Re: Filament Run-out Sensor Add-on

Well thought I would go ahead and chime in on this thread here. I have installed the filament sensor on our N2 Plus at work and it does absolutely nothing when filament runs out. I have even started a print with no filament and it starts like normal and ghost prints. Pretty disappointed in this &quo...
by claytony565
Mon May 07, 2018 4:16 pm
Forum: User's Gallery
Topic: First Month of Printing
Replies: 4
Views: 1421

First Month of Printing

Just thought I would share some of the results I have gotten after about a month or so of printing. I am using this printer at work for prototyping and visual aids and it has been working great. Most impressive print has been a functioning nut and bolt combo. Tolerances are great, I printed almost a...

Go to advanced search