Search found 194 matches

by Alex M.
Wed Apr 25, 2018 2:11 pm
Forum: General
Topic: Anyone have a spool of Raise3D Premium Red? / Restock time?
Replies: 6
Views: 3857

Re: Anyone have a spool of Raise3D Premium Red? / Restock time?

We just received our printer yesterday with a Red spool included. I’ll have to check with my manager if he would be ok selling it. I can’t see us wanting the red filament but can’t say for sure.
by Alex M.
Mon Apr 23, 2018 8:31 pm
Forum: Hardware
Topic: Improvements by using TMC2130 driver.
Replies: 82
Views: 42052

Re: Improvements by using TMC2130 driver.

You will have to swap the positions on some of the wires at the motor as mentioned by Jetguy several posts above. Or put the old driver back in. One additional note: If you upgrade the stock A4988 drivers to other drivers like 2208s or 2224s, there is a chance that motor rotation direction could be ...
by Alex M.
Mon Apr 23, 2018 7:57 am
Forum: Hardware
Topic: Improvements by using TMC2130 driver.
Replies: 82
Views: 42052

Re: Improvements by using TMC2130 driver.

Jetguy - Thanks for clarification and information about the drivers. I am mainly worried about the once in a blue moon issue with the 2100s. I can get the 2208s easier via DIgikey, already have the headers (pins), and would just need to get some heatsinks.

Thanks again!
by Alex M.
Mon Apr 23, 2018 5:29 am
Forum: Hardware
Topic: Improvements by using TMC2130 driver.
Replies: 82
Views: 42052

Re: Improvements by using TMC2130 driver.

Just for clarification, if one is to use the 2224 drivers, all that needs to be done is change the dip switches and adjust the voltage.(?). While if one was to use the 2208 driver, it seems there are two options; 1. Is hardware configuration which you set the switches & voltage. Or, 2. Where you...
by Alex M.
Sun Apr 22, 2018 4:02 pm
Forum: Hardware
Topic: Improvements by using TMC2130 driver.
Replies: 82
Views: 42052

Re: Improvements by using TMC2130 driver.

Sorry to hear that. I was hoping it was just the drivers but feared it could be more. Hopefully it is just the fuse on the motion board. Fingers crossed for you!
by Alex M.
Sun Apr 22, 2018 4:44 am
Forum: Hardware
Topic: Improvements by using TMC2130 driver.
Replies: 82
Views: 42052

Re: Improvements by using TMC2130 driver.

Comparing your pictures to those posted by Jetguy, it looks like you installed them backwards (180 degrees).
But I don’t know for sure.
by Alex M.
Sat Apr 21, 2018 3:50 am
Forum: Hardware
Topic: Filament Run-out Sensor Add-on
Replies: 89
Views: 25439

Re: Filament Run-out Sensor Add-on

Wow! That would be extremely frustrating. Thanks for the information. Any sense of where it mounts?
by Alex M.
Fri Apr 20, 2018 9:31 pm
Forum: Hardware
Topic: Filament Run-out Sensor Add-on
Replies: 89
Views: 25439

Re: Filament Run-out Sensor Add-on

The sensor will be located between the filament spool holders and the feeding tube. Should have no relationship to the extruder itself. Is this still the case? Your California office seemed to think it was mounted on the extruder like the new Pro2. When I questioned them about it and told them what...
by Alex M.
Thu Apr 19, 2018 11:12 pm
Forum: General
Topic: Looking for a printer, should we buy a new Pro2, new N2 or a used N2?
Replies: 7
Views: 4889

Re: Looking for a printer, should we buy a new Pro2, new N2 or a used N2?

Just wanted to come back and say thank you to all who replied and all the others on this forum whom make it such a great place! Today we place an order for a N2 Plus Single extruder which should be here early next week. We went back and forth on what would be best for us and finally decided on the N...
by Alex M.
Tue Apr 17, 2018 5:52 pm
Forum: General
Topic: Looking for a printer, should we buy a new Pro2, new N2 or a used N2?
Replies: 7
Views: 4889

Re: Looking for a printer, should we buy a new Pro2, new N2 or a used N2?

Thanks for the replies. I work for a small metabolic instrument company and we are looking for a printer that will mainly be used to help us prototype parts which will eventually be extruded or cast. We are trying to reduce development cost by cutting down on the revisions of custom fixtures. The pr...
by Alex M.
Mon Apr 16, 2018 11:26 pm
Forum: General
Topic: Looking for a printer, should we buy a new Pro2, new N2 or a used N2?
Replies: 7
Views: 4889

Looking for a printer, should we buy a new Pro2, new N2 or a used N2?

Hello All, I'm new here and trying to gather as much information as possible for an upcoming 3D printer purchase. I really like the Pro2 series however became a bit concerned with the new motion controller since it will be closed source firmware. From my research there have been several community pr...
by Alex M.
Mon Apr 16, 2018 4:37 pm
Forum: Feature Requests, Ideas, Wishes
Topic: Really perfect self repair instructions ...
Replies: 5
Views: 2206

Re: Really perfect self repair instructions ...

Sorry if I have to mention this time the competition, but since I myself was a customer of Zortrax I have to mention the MODEL support page of Zortrax ... SO must be a support page for your own hardware / software that truly explains StepbyStep's instructions for repair and / or problems. RAISE3D i...
by Alex M.
Sun Apr 15, 2018 4:38 pm
Forum: General
Topic: Thermal-Protector - available soon to all
Replies: 117
Views: 82850

Re: Thermal-Protector - available soon to all

When will these be standard, ie. pre-installed, on new N2 series printers?
by Alex M.
Sat Apr 14, 2018 6:37 pm
Forum: General
Topic: Just Released N2 Pro
Replies: 124
Views: 48861

Re: Just Released N2 Pro

Hey Vicky, whats about auto bed leveling? We are considering to buy the new pro version. But, if there is and will be no auto bed leveling, we may stick with the N2. We have done the BL-Touch mod, which only was possible due to the marlin firm. From our tests, we think that mechanical pre-calibrati...

Go to advanced search