Search found 92 matches

by mdana
Thu Jul 23, 2020 7:50 pm
Forum: Pro2 Series
Topic: Touchscreen not working on Pro2
Replies: 9
Views: 623

Re: Touchscreen not working on Pro2

How old is the printer? My touchscreen failed about a week before it went out of warranty (3 months for electronics?) and was about to get it replaced.
by mdana
Thu Jul 09, 2020 1:36 am
Forum: Pro2 Series
Topic: Bed Leveling Hardware
Replies: 9
Views: 1858

Re: Bed Leveling Hardware

Even manual mesh bed leveling would be a solution.
by mdana
Wed Jul 08, 2020 5:00 pm
Forum: Pro2 Series
Topic: Nozzles randomly switching during print
Replies: 3
Views: 257

Re: Nozzles randomly switching during print

Hi, flexing the servo cable doesn't seem to have an effect, but moving the cable chain does.
by mdana
Tue Jul 07, 2020 7:12 am
Forum: Pro2 Series
Topic: Nozzles randomly switching during print
Replies: 3
Views: 257

Nozzles randomly switching during print

I noticed that when the printer is idle, the nozzles will switch on their own. I didn’t see any damage to the cable running between the filament sensor and the servo.
by mdana
Tue Jul 07, 2020 7:02 am
Forum: General
Topic: 2 year with PRO 2
Replies: 13
Views: 2682

Re: 2 year with PRO 2

Been printing two years with a Pro and one year with a Pro Plus. Ditto all the comments. The hot end is a nightmare! I would hope, at some point, Raise3d offers a replacement hotend that is a bolt-on replacement for this nightmare. Slice Engineering’s Copperhead is a drop in replacement heat break ...
by mdana
Sat May 16, 2020 8:57 pm
Forum: Pro2 Series
Topic: Liquid cooling for everyone
Replies: 115
Views: 8245

Re: Liquid cooling for everyone

cant seems to find half the stuff on Amazon US. usually copying the technical name from German Amazon to US yields better results. You can find tubing and fittings on McMaster-Carr. I can try and put together a list of the parts I used, but I don’t have the printer in front of me (office is shutdow...
by mdana
Wed May 13, 2020 3:07 am
Forum: Pro2 Series
Topic: PLA blockage
Replies: 9
Views: 727

Re: PLA blockage

Thank you for all your replies and your warm welcome Markus64. I have taken Markus's advice and started to machine a couple of water jackets closely following his designs from the pictures on this site. I am having problems trying to locate the barbed fittings on the jacket. The only versions i can...
by mdana
Sat May 02, 2020 12:07 am
Forum: Pro2 Series
Topic: Liquid cooling for everyone
Replies: 115
Views: 8245

Re: Liquid cooling for everyone

Bummer, is there a bad solder joint or something on the actual radiator? I’m using the same/similar kit from E3D and haven’t had any issues, but I’m not sure if it’s any better than the kits on AliExpress.
by mdana
Fri May 01, 2020 5:12 am
Forum: Pro2 Series
Topic: Liquid cooling for everyone
Replies: 115
Views: 8245

Re: Liquid cooling for everyone

Looks good. Might be a good idea to flush them out before installing them in your loop so that any leftover powder doesn’t get in the pump.
by mdana
Mon Apr 27, 2020 11:08 pm
Forum: Pro2 Series
Topic: Liquid cooling for everyone
Replies: 115
Views: 8245

Re: Liquid cooling for everyone

How are you powering the pump and fan? My original plan was to tap into the power supply on the printer, but ended up using a DC adapter that’s plugged into a power strip (along with the printer).
by mdana
Tue Apr 21, 2020 10:33 pm
Forum: General
Topic: Belt issues pro2
Replies: 6
Views: 1297

Re: Belt issues pro2

You might have a broken coupler.
by mdana
Tue Apr 21, 2020 10:26 pm
Forum: Pro2 Series
Topic: Liquid cooling for everyone
Replies: 115
Views: 8245

Re: Liquid cooling for everyone

I had to scrap the first set of parts that I made. OUCH! :o :x Still very well done, mdana! What can you report positive about your mod? Did you ever have problems like heat creeping or overheating the hotend after the conversion? This solved the heat creep issues and haven’t had any issues with le...
by mdana
Tue Apr 21, 2020 10:10 pm
Forum: Pro2 Series
Topic: Liquid cooling for everyone
Replies: 115
Views: 8245

Re: Liquid cooling for everyone

Update: The design of the heat exchanger is basically finished. I will have two prototypes made from aluminum using a 3D printing SLM process. I expect the finished components to be available until around mid-May. The water cooling system "Titan Aqua Watercooling" from e3D is used as the ...
by mdana
Tue Apr 21, 2020 9:48 pm
Forum: Pro2 Series
Topic: Liquid cooling for everyone
Replies: 115
Views: 8245

Re: Liquid cooling for everyone

Here are the CAD files for the water blocks (DMLS and machined version): https://www.dropbox.com/s/yc0g07a067fksfd/Water%20Block%2C%20Cross%20Drilled.STEP?dl=0 https://www.dropbox.com/s/q93w5ug9f3lji4s/Water%20Block%2C%20DMLS.STEP?dl=0 The machined version is cross drilled and plugged with M4 set sc...
by mdana
Tue Apr 21, 2020 2:36 am
Forum: Pro2 Series
Topic: Liquid cooling for everyone
Replies: 115
Views: 8245

Re: Liquid cooling for everyone

I have a similar design that was printed in aluminum as well as a machined version. I can share both step files as well as the SolidWorks model. One bit of warning, make sure you have enough clearance on the back of the block so it doesn’t interfere with the housing for the nozzle lifting servo. I h...
by mdana
Sun Apr 19, 2020 2:26 am
Forum: General
Topic: Clog or heat creep
Replies: 24
Views: 4371

Re: Clog or heat creep

I’m using E3D’s water cooling kit (https://e3d-online.com/water-cooling-kit) and printed (DMLS) the water blocks out of aluminum. There’s more info on water cooling in this thread: https://forum.raise3d.com/viewtopic.php?t=10787
by mdana
Fri Apr 17, 2020 9:42 am
Forum: General
Topic: Clog or heat creep
Replies: 24
Views: 4371

Re: Clog or heat creep

I ended up solving the problem by water cooling the heat sinks.
by mdana
Fri Apr 17, 2020 9:36 am
Forum: Pro2 Series
Topic: ERROR: Network not connected
Replies: 40
Views: 6148

Re: ERROR: Network not connected

On my Pro2 Plus, the extension cable that runs from the board to the back of the printer was bad. I was able to get a new cable under warranty, but never got around to installing it and just connected the Ethernet cable directly to the board.
by mdana
Mon Apr 13, 2020 4:05 am
Forum: Pro2 Series
Topic: Nozzle cleaning
Replies: 2
Views: 2703

Re: Nozzle cleaning

I’ve never had any issues with the nozzle itself clogging. Typically, clogs or jams are due to heat creep above the heat break or if the nozzle wasn’t installed correctly (not hot tightened against the heat break).
by mdana
Fri Apr 03, 2020 7:47 pm
Forum: General
Topic: Clog or heat creep
Replies: 24
Views: 4371

Re: Clog or heat creep

Are you using thermal paste on the heat break/heater block?

Go to advanced search