Search found 51 matches

by FreedomRules
Tue Aug 27, 2019 5:53 pm
Forum: Hardware
Topic: switchable / dimmable LED-Strips
Replies: 2
Views: 552

Re: switchable / dimmable LED-Strips

Wouldn't take much with something like an adjustable DC-DC buck converter to allow adjustment via a pot. All a buck converter does is allow you to control the DC output voltage from what the input is down to zero volts. You can get them on Amazon one ebay pretty cheap. One could take it a step furth...
by FreedomRules
Tue Aug 27, 2019 4:17 pm
Forum: N Series
Topic: Upgraded to a Duet 2 Controller
Replies: 0
Views: 290

Upgraded to a Duet 2 Controller

I finally got around to upgrading the controller on my Raise3D to a Duet 2 Wifi Controller with filament monitoring. I just got what I'd consider phase 1 completed yesterday. The new main board in and printing and it took a fair amount of new wiring. Actually with no calibrations done yet it printed...
by FreedomRules
Sun Aug 04, 2019 10:03 pm
Forum: Hardware
Topic: KevinOConnor/klipper Firmware
Replies: 2
Views: 445

Re: KevinOConnor/klipper Firmware

It would appear your right. I guess instead of wasting my time trying to get it to work with Raise3D hardware. I'll just buy a Duet2 board and hook it up and then use it with the Klipper firmware. Basically your 3D printers board just handles the movements. All the calculations are done on another m...
by FreedomRules
Thu Aug 01, 2019 2:57 am
Forum: Hardware
Topic: KevinOConnor/klipper Firmware
Replies: 2
Views: 445

KevinOConnor/klipper Firmware

Has anyone flashed this firmware onto a Raise3d printer? If so whats your thoughts...
by FreedomRules
Thu Aug 01, 2019 1:52 am
Forum: Hardware
Topic: Project: The next heated bed
Replies: 37
Views: 10910

Re: Project: The next heated bed

I went with a custom sized pad from. https://www.keenovo.com that matched my aluminum plate size. Then I purchased a schaffner FN9290-10-06 power module to replace the stock one. This then breaks out to a couple relay's that then power the whole printer plus the bed since it runs off 120V ac. I don'...
by FreedomRules
Mon Oct 01, 2018 4:24 am
Forum: Hardware
Topic: New Heated Bed Reads 738 degrees with no heat
Replies: 8
Views: 1541

Re: New Heated Bed Reads 738 degrees with no heat

I had got this working but the reported temperature was jumping alot with fluctuations of 20 degrees at most but averaged 5 degree bouncing. Even when it wasn't heating. Well after a a lot of different configurations I finally landed on one that worked. Which was building a RC Low-Pass filter inline...
by FreedomRules
Sun Sep 23, 2018 4:29 am
Forum: Hardware
Topic: New Heated Bed Reads 738 degrees with no heat
Replies: 8
Views: 1541

Re: New Heated Bed Reads 738 degrees with no heat

So when I get this hooked up is the temperature that is displayed suppose to be somewhat right or will the PID autotune fix that? I always thought PID autotune was more for how the bed heats and recovers not anything to do with what the temperature shows. It shows a temp of 295 with ABH Marlin 1.9. ...
by FreedomRules
Fri Sep 21, 2018 5:31 pm
Forum: Hardware
Topic: New Heated Bed Reads 738 degrees with no heat
Replies: 8
Views: 1541

Re: New Heated Bed Reads 738 degrees with no heat

Well I got a little farther last night. I cut out all the wiring I had done before and this time just did it all on a breadboard so I could rewire if necessary to find the right config. Currently my issue is that it shows 9 degree's vs 20 degree's like both my extruder's show as I'd think they'd sho...
by FreedomRules
Thu Sep 20, 2018 9:15 pm
Forum: Hardware
Topic: New Heated Bed Reads 738 degrees with no heat
Replies: 8
Views: 1541

Re: New Heated Bed Reads 738 degrees with no heat

Sweet I will try this tonight. Hopefully I have a 4.7 laying around.
by FreedomRules
Thu Sep 20, 2018 5:33 pm
Forum: Hardware
Topic: New Heated Bed Reads 738 degrees with no heat
Replies: 8
Views: 1541

New Heated Bed Reads 738 degrees with no heat

So I'm on the tail end of upgrading my bed like Socke did with a flat thick aluminum plate. I also upgraded the heater to a keenovo 120V 750 watt silicon heater. It comes with a 2 wire 100k B25°C/50°C=3950±1% thermistor. I then followed what I saw on a couple arduino posts and wired it up with a 10k...
by FreedomRules
Tue Sep 18, 2018 3:25 am
Forum: Hardware
Topic: Project: The next heated bed
Replies: 37
Views: 10910

Re: Project: The next heated bed

Wiring temp sensor. Did you add the 10k pull-up resistor and maintain 3 wire hookup or did you just do the 5v and ground and skip the sensor pin while still changing the setting in the Marlin firmware #define TEMP_SENSOR_BED 11? That or use completely different pins on the board? Only difference on ...
by FreedomRules
Fri Aug 17, 2018 4:29 am
Forum: General
Topic: PRO2 real speed much lower than set speed
Replies: 10
Views: 1726

Re: PRO2 real speed much lower than set speed

Vicky can you answer what the volumetric build rate of your printers are at the different resolutions. Preferable in cm3/hr measure scale.
by FreedomRules
Fri Aug 17, 2018 2:59 am
Forum: General
Topic: PRO2 real speed much lower than set speed
Replies: 10
Views: 1726

Re: PRO2 real speed much lower than set speed

Curious if you tried putting it in vase mode for cylindrical shapes to see if it printed as expected? What slicing software did you use? What was all your settings at? Not sure stating that a direct drive will always be slower than bowden systems is a fair statement. The printer that MIT recently bu...
by FreedomRules
Fri Aug 17, 2018 2:45 am
Forum: Hardware
Topic: Project: The next heated bed
Replies: 37
Views: 10910

Re: Project: The next heated bed

I finally found a supplier in the USA for a cast milled 3/8 aluminum plate. https://www.midweststeelsupply.com/store/castaluminumplateatp5 tolerance is .015" on flatness and .0015" on thickness. I'd like the flatness a litter tighter on its tolerance but will try it first before continuing...
by FreedomRules
Tue Aug 07, 2018 7:49 pm
Forum: General
Topic: E3D V6 on Pro2
Replies: 16
Views: 3558

Re: E3D V6 on Pro2

I'd like to know how Raise3D did the auto lift feature? Currently I'm working on a whole new carriage that would use micro steppers to lift and lower the print head along with built in sensors that work with the print head as the device that presses against the bed to detect exact bed height. The i...
by FreedomRules
Tue Aug 07, 2018 5:29 pm
Forum: Hardware
Topic: Pro buildplate
Replies: 10
Views: 2316

Re: Pro buildplate

That is the reason why we are not going to provide those parts for the upgrade, or the users need to do a lot modification works to make the upgrade works which may do harm to the printer. What happens if a user harms the printer? I'd assume you'd get a sale of a new PRO2 or the user would get a ne...
by FreedomRules
Sat Aug 04, 2018 6:22 am
Forum: General
Topic: E3D V6 on Pro2
Replies: 16
Views: 3558

Re: E3D V6 on Pro2

I'd like to know how Raise3D did the auto lift feature? Currently I'm working on a whole new carriage that would use micro steppers to lift and lower the print head along with built in sensors that work with the print head as the device that presses against the bed to detect exact bed height. The id...
by FreedomRules
Sat Aug 04, 2018 5:53 am
Forum: Hardware
Topic: Pro buildplate
Replies: 10
Views: 2316

Re: Pro buildplate

Would anyone be interested in a kit version of Socke's new bed he built. http://forum.raise3d.com/viewtopic.php?f=4&t=1590 I'm still compiling all the pieces I need to build my own. Right now I'm getting bids on the 8mm thick aluminum bed. Not sure what the price point would come in at. May be p...
by FreedomRules
Sat Aug 04, 2018 5:43 am
Forum: Hardware
Topic: Pro buildplate
Replies: 10
Views: 2316

Re: Pro buildplate

But Raise3D answer to a post asking for the installation of the pro plate on the N series: Confirmed with the R&D team, both two upgrades you asked needs to drill the base plate to carry out the installation. That is the reason why we are not going to provide those parts for the upgrade, or the...
by FreedomRules
Tue Jul 24, 2018 6:55 pm
Forum: General
Topic: Upgrade Components for N Series are Coming!
Replies: 14
Views: 3358

Re: Upgrade Components for N Series are Coming!

When you say "Dual Extruder" does this include the ability to raise and lower the left and right nozzle? Pretty sure she's just referring to this: http://shop.bondtech.se/en/upgrade-kits/raise3d/raise3d-dualdirect-upgrade.html I wish they'd do this but it would likely curb alot of existin...

Go to advanced search