Search found 155 matches

by DeX
Wed Jul 31, 2019 8:49 pm
Forum: N Series
Topic: N2 network plug out
Replies: 2
Views: 131

Re: N2 network plug out

Reinstalled my router and problem went away :oops:
by DeX
Mon Jul 22, 2019 6:33 am
Forum: N Series
Topic: N2 network plug out
Replies: 2
Views: 131

N2 network plug out

i've got State: Plug Out under the Ethernet menu at the touch screen.
I use Wifi all the time.
any ideas?

ticket created.

printer was turned off and on!
firmware reinstalled...
by DeX
Sun Jul 14, 2019 5:07 am
Forum: Feature requests, ideas, wishes
Topic: Double infill before surface
Replies: 7
Views: 462

Re: Double infill before surface

I found this feature on a cura's video... It's named Gradual Infill Steps.
by DeX
Wed Jul 10, 2019 8:43 am
Forum: Software
Topic: Disable the "Task finished" menu after printing in the latest RaiseTouch
Replies: 7
Views: 816

Re: Disable the "Task finished" menu after printing in the latest RaiseTouch

You start to print but nozzle is too close or not stick good or else... press stop. then quickly(because it is coooooooooooling) warm up nozzle and bed... wait ...and start again.. TIME TIME TIME.
by DeX
Wed Jul 10, 2019 8:40 am
Forum: Software
Topic: Disable the "Task finished" menu after printing in the latest RaiseTouch
Replies: 7
Views: 816

Re: Disable the "Task finished" menu after printing in the latest RaiseTouch

OK.
The irritation from these menus at the end of the print is comparable, perhaps, with the constant activation of the table and nozzle heating after an unsuccessful start ... Argh!
by DeX
Sun Jul 07, 2019 8:57 pm
Forum: N Series
Topic: N2 plus poor quality
Replies: 3
Views: 534

Re: N2 plus poor quality

Thank you for explaining!
by DeX
Sat Jul 06, 2019 2:51 am
Forum: Software
Topic: Dense Support Layers at Bottom of Supports on Part
Replies: 6
Views: 662

Re: Dense Support Layers at Bottom of Supports on Part

Хорошо, сделайте нижний dense опциональным! Чаще всего он только мешает и занимает время.
by DeX
Fri Jul 05, 2019 7:39 pm
Forum: Software
Topic: Disable the "Task finished" menu after printing in the latest RaiseTouch
Replies: 7
Views: 816

Re: Disable the "Task finished" menu after printing in the latest RaiseTouch

Раздражение от этих меню в конце печати сравнимо разве что с постоянным включением подогрева стола и сопла после неудачного старта... Аргх!
by DeX
Sat Jun 22, 2019 7:49 pm
Forum: N Series
Topic: N2 plus poor quality
Replies: 3
Views: 534

Re: N2 plus poor quality

How is your n2plus prints full height?
by DeX
Sat Jun 22, 2019 7:48 pm
Forum: N Series
Topic: What does it do ?
Replies: 3
Views: 283

Re: What does it do ?

Jetguy wrote:Seen before in this topic https://forum.raise3d.com/viewtopic.php ... lar#p21954

Спасибо, всё понятно!
by DeX
Wed Jun 19, 2019 8:17 pm
Forum: N Series
Topic: What does it do ?
Replies: 3
Views: 283

What does it do ?

Какой смысл в этих штуках на валах? Они часто двигаются почти свободно туда сюда...
by DeX
Tue Jun 18, 2019 3:05 am
Forum: N Series
Topic: "thunk" sound along the Y axis
Replies: 14
Views: 736

Re: "thunk" sound along the Y axis

Надо ли мне отправлять принтер с такой поломкой в город за 700км для диагностики, чтобы заменить муфту по гарантии. Да в принтере ещё что-нибудь сломается за это время! Господа, американцы, у вас какие расстояния между городов? :)
Sad. I just will buy it.
by DeX
Sat Jun 15, 2019 6:59 pm
Forum: General
Topic: 8.5 day, 1242.5 g print - Am I tempting fate? - Questions
Replies: 14
Views: 1533

Re: 8.5 day, 1242.5 g print - Am I tempting fate? - Questions

I bet overall time could be reduced a lot! You may use light supports(10-15%) but turn it to 30% and with dense right before print a surface... You may change infill from lines to rectangular.. (+ bottom and top layers too). You may not to use raft. And so on :) I wanna try to slice and calculate :)...
by DeX
Fri Jun 14, 2019 9:45 am
Forum: RaiseCloud
Topic: raise cloud reporting
Replies: 6
Views: 596

Re: raise cloud reporting

I use Cloud version only for control printers thru the raise app.
btw
by DeX
Thu Jun 13, 2019 10:08 am
Forum: General
Topic: t-shirt
Replies: 2
Views: 792

Re: t-shirt

jvingaard wrote:I really want to buy a Raise3D t-shirt, but where?

3DPrint it on a t-shirt! :D
by DeX
Thu Jun 06, 2019 9:27 am
Forum: Feature requests, ideas, wishes
Topic: Double infill before surface
Replies: 7
Views: 462

Re: Double infill before surface

I meant would be nice if IM automatically doubles the infill before printing a surface (depends on sq mm).
In some way a DENSE infill for bridges(first layers)
by DeX
Wed Jun 05, 2019 7:12 am
Forum: Feature requests, ideas, wishes
Topic: Double infill before surface
Replies: 7
Views: 462

Double infill before surface

Сейчас приходится делать в ручную, что занимает много времени.
Иначе на infill 5% слои кладутся плохо и возможны даже сбои слоёв и прочие неприятности.

doubleinfill.png
by DeX
Tue Jun 04, 2019 2:33 am
Forum: Software
Topic: Remove filament settings and Pinters
Replies: 3
Views: 286

Re: Remove filament settings and Pinters

Vicky@Raise3D wrote:Thanks for your suggestion. We have added it into list and we are working on it.

Since 2018? :)

Go to advanced search