Search found 242 matches

by socke
Thu Aug 15, 2019 11:48 am
Forum: Software
Topic: Print complete message on N2 touch screen
Replies: 4
Views: 534

Re: Print complete message on N2 touch screen

It's always good to know, I'm not the only strange person on this planet... :mrgreen:
by socke
Tue Aug 13, 2019 3:44 pm
Forum: Software
Topic: Print complete message on N2 touch screen
Replies: 4
Views: 534

Print complete message on N2 touch screen

I'm not sure if this has been already addressed before: For me it is very annoying (!!!) to be forced going to my printer and pressing 2 buttons after each print. You should really make this 'feature' configurable if somebody needs it. I'm aware that it needs some attention to not start a print with...
by socke
Mon Apr 22, 2019 12:00 pm
Forum: Software
Topic: Single extruder printer is detecting dual extrusion prints
Replies: 1
Views: 261

Single extruder printer is detecting dual extrusion prints

After upgrading my single extrusion N2 to RaiseTouch 1.2.0, I'm getting an error message in RaiseTouch, telling me that there are dual extrusion commands in my print file. It doesn't ask me if I would like to print anyways, it just denies to print! I'm printing with the same settings since months wi...
by socke
Mon Sep 24, 2018 8:37 am
Forum: Hardware
Topic: New Heated Bed Reads 738 degrees with no heat
Replies: 8
Views: 1557

Re: New Heated Bed Reads 738 degrees with no heat

To clarify wiring. on the logic board we have ground, 5v and S. I wired 5v to one leg of thermistor and ground to other leg of thermistor. Then I wired a 4.7k resistor to the 5v wire and on the other end of the resistor I wired it to the S leg. My wires are different colors than your is why I didn'...
by socke
Fri Sep 21, 2018 6:18 am
Forum: Hardware
Topic: New Heated Bed Reads 738 degrees with no heat
Replies: 8
Views: 1557

Re: New Heated Bed Reads 738 degrees with no heat

This is exactly the same I did, as I wrote here. I just didn't find a good photo of the wiring. ;)
by socke
Tue Sep 18, 2018 2:11 pm
Forum: Hardware
Topic: Project: The next heated bed
Replies: 37
Views: 10997

Re: Project: The next heated bed

If I remember right, I built a 3 wire cable (or modified the existing one?) with a 1/4 Watt wired pullup resistor near the plug. I directly plugged this into the original socket on the main board. So in Marlin I didn't change any pin configuration, just the sensor type.
by socke
Wed Jun 27, 2018 5:28 am
Forum: Software
Topic: LIN_ADVANCE = better extrusion control
Replies: 135
Views: 27783

Re: LIN_ADVANCE = better extrusion control

Is your Outline Direction set to 'Inside-Out' or 'Outside-In'? Generally, I'm getting cleaner results with 'Inside-Out'.
by socke
Wed Jun 20, 2018 8:46 am
Forum: General
Topic: Your favorite PLA Brand
Replies: 12
Views: 2147

Re: Your favorite PLA Brand

Ingeo 3D850 and Ingeo 3D870 based PLA, available from different brands. 3D850 is general purpose and very easy printable, 3D870 is not exactly so smooth to print but very stiff (more than ABS) - I'm using it mostly for mechanical parts. I'm buying it in this shop: https://www.hta3d.com/en/filament/p...
by socke
Wed Mar 21, 2018 1:47 pm
Forum: Hardware
Topic: TOP COVER Replacement N2+N2 Plus
Replies: 18
Views: 4075

Re: TOP COVER Replacement N2+N2 Plus

I like it, nice work! :)
Most likely I will build one as well, if you share the files ...
by socke
Mon Mar 12, 2018 11:22 am
Forum: Hardware
Topic: Improvements by using TMC2130 driver.
Replies: 82
Views: 31032

Re: Improvements by using TMC2130 driver.

@Iamkar33m:
I already have had the situation, that the same model printed at different locations on the bed could succeed or fail because of lost steps (layer shifts). $20 are definitely worth avoiding these headaches...
by socke
Sun Mar 11, 2018 1:53 pm
Forum: Hardware
Topic: Improvements by using TMC2130 driver.
Replies: 82
Views: 31032

Re: Improvements by using TMC2130 driver.

I just completed the first print after doing this mod. Everything went very well.
Thanks ABH for sharing this and your comprehensive write up!
:)
by socke
Sat Mar 10, 2018 12:44 pm
Forum: Hardware
Topic: Improvements by using TMC2130 driver.
Replies: 82
Views: 31032

Re: Improvements by using TMC2130 driver.

Never mind. I found, it's a library which needs to be installed first. ;-)
by socke
Sat Mar 10, 2018 10:10 am
Forum: Hardware
Topic: Improvements by using TMC2130 driver.
Replies: 82
Views: 31032

Re: Improvements by using TMC2130 driver.

@ABH:
I'm just doing the same mod, but can't build your firmware from the TMC2208 branch. It seems, the TMC2208Stepper.h is missing there. Could you please check that?

Thanks!
by socke
Tue Feb 06, 2018 6:28 am
Forum: Software
Topic: LIN_ADVANCE = better extrusion control
Replies: 135
Views: 27783

Re: LIN_ADVANCE = better extrusion control

Yes, I configured the printer via touch screen as single extruder. I could PM you my configuration?
by socke
Sat Feb 03, 2018 4:17 pm
Forum: Software
Topic: LIN_ADVANCE = better extrusion control
Replies: 135
Views: 27783

Re: LIN_ADVANCE = better extrusion control

@ABH: You saved my day! The first build of your sources resulted in a successfully printed calibration box with LIN_ADVANCE enabled (looks very promising).
I was just thinking about throwing away the touchscreen and using a clean Marlin...
Thanks for sharing your work!
by socke
Sat Feb 03, 2018 3:02 pm
Forum: Software
Topic: LIN_ADVANCE = better extrusion control
Replies: 135
Views: 27783

Re: LIN_ADVANCE = better extrusion control

@ABH: Thanks, I will try your fork and report back. Before I thought it was only a clone of firespeds repository.
by socke
Sat Feb 03, 2018 2:14 pm
Forum: Software
Topic: LIN_ADVANCE = better extrusion control
Replies: 135
Views: 27783

Re: LIN_ADVANCE = better extrusion control

The thermal runaway protection seems to be not the only one problem: In a last act of despair, I completely disabled the thermal runaway protection (which was not that easy, thanks Marlin). But again, nothing happens after heating up everything - the print just doesn't start. Maybe touch screen comm...
by socke
Sat Feb 03, 2018 1:09 pm
Forum: Software
Topic: LIN_ADVANCE = better extrusion control
Replies: 135
Views: 27783

Re: LIN_ADVANCE = better extrusion control

Thanks! :mrgreen:
by socke
Sat Feb 03, 2018 12:51 pm
Forum: Software
Topic: LIN_ADVANCE = better extrusion control
Replies: 135
Views: 27783

Re: LIN_ADVANCE = better extrusion control

Thanks Jetguy for pointing to this. I didn't see this thread earlier. But I did also see the behavior in some previous version, that a entered temperature was reset. I couldn't test further because lack of time for this and so I reverted to my previous version at this point in time. However, this do...
by socke
Sat Feb 03, 2018 11:58 am
Forum: Hardware
Topic: Project: The next heated bed
Replies: 37
Views: 10997

Re: Project: The next heated bed

Awesome mod. I'm wanting to print polycarbonate and seems you want at least 130C to do that. Maybe I'm blind and I didn't see it but whats the max stable bed temp you can hit with this. I was looking at bed heaters from Keenovo as they seem pretty powerful beds and they seem to have a well diversif...

Go to advanced search