Search found 19 matches

by Redron357
Thu May 23, 2019 12:47 am
Forum: Software
Topic: CAMERA VIDEO
Replies: 16
Views: 1260

Re: CAMERA VIDEO

also I can only export to mjpg nothing else
by Redron357
Thu May 23, 2019 12:46 am
Forum: Software
Topic: CAMERA VIDEO
Replies: 16
Views: 1260

Re: CAMERA VIDEO

let me add data, I can go to the dashboard and see and play the video in the dashboard, but after I export the video there is only a still image. I use VLC player to open the file.
by Redron357
Thu May 23, 2019 12:36 am
Forum: Software
Topic: CAMERA VIDEO
Replies: 16
Views: 1260

Re: CAMERA VIDEO

the file is good unzip it with WinRAR its just a still image of my printbed
by Redron357
Thu May 23, 2019 12:33 am
Forum: Software
Topic: CAMERA VIDEO
Replies: 16
Views: 1260

Re: CAMERA VIDEO

its a zipped file
by Redron357
Fri May 17, 2019 9:06 pm
Forum: Software
Topic: CAMERA VIDEO
Replies: 16
Views: 1260

Re: CAMERA VIDEO

Vicky@Raise3D wrote:Would you like to share us the video or image you export from touchscreen so that we can help check what's going on?
Is it possible to have the out of focus lens issue also shown in a video?




Here's the file
by Redron357
Mon Apr 22, 2019 12:40 pm
Forum: Software
Topic: CAMERA VIDEO
Replies: 16
Views: 1260

Re: CAMERA VIDEO

HouseMonster wrote:If you rotate the lens you can change the focus point of the image. Had to do this with my Pro2



thank you
by Redron357
Mon Apr 22, 2019 12:39 pm
Forum: Software
Topic: CAMERA VIDEO
Replies: 16
Views: 1260

Re: CAMERA VIDEO

here's the file
by Redron357
Sun Apr 14, 2019 7:32 pm
Forum: Software
Topic: CAMERA VIDEO
Replies: 16
Views: 1260

CAMERA VIDEO

Hello all, 1 Camera is installed setting correct as per Raise3D support Kevin. on the dash board I see the short video and I export it and all I get is a Picture of the bed, no print video. 2 camera is clear at something close to the lens but where the printing is done seems like the lens is out of ...
by Redron357
Sun Apr 14, 2019 7:18 pm
Forum: Hardware
Topic: Camera Installation
Replies: 2
Views: 1224

Re: Camera Installation

corrent feed the cable to the back top plastic side and then to the top to the chain hole
by Redron357
Fri Oct 20, 2017 7:33 pm
Forum: User's Gallery
Topic: Thor Hammer/Captain America Shield
Replies: 21
Views: 5608

Re: Thor Hammer/Captain America Shield

Have uploaded the Stl files anywhere I do like your work
by Redron357
Fri Oct 20, 2017 6:52 pm
Forum: User's Gallery
Topic: Full size R2 D2
Replies: 12
Views: 3726

Re: Full size R2 D2

Did you finish the R2 D2
by Redron357
Fri Mar 10, 2017 3:50 am
Forum: Hardware
Topic: Tubes or no tubes
Replies: 2
Views: 976

Tubes or no tubes

This is the question, Tubes or No Tubes... I have found with the tubes on, the weight of the tube and filament cause the unused filament to sag as I am printing. I have taken these tubes off and find I have the same problem the unused filament ( if I only use 1 filament to print ) tends to sag so ba...
by Redron357
Wed Mar 08, 2017 10:27 pm
Forum: Hardware
Topic: Remote upload often extremely slow and fails...again
Replies: 12
Views: 3772

Re: Remote upload often extremely slow and fails...again

May I ask a question 1. where did you look to see the Firmware Version, and 2. what version are you running
by Redron357
Tue Mar 07, 2017 1:09 am
Forum: Hardware
Topic: Remote upload often extremely slow and fails...again
Replies: 12
Views: 3772

Re: Remote upload often extremely slow and fails...again

Has this problem been Fixed, I just purchased a N2 1 week ago and I have the problem uploading is Slowwwww. has failed sometimes as well but is slow.
by Redron357
Mon Mar 06, 2017 10:19 pm
Forum: User's Gallery
Topic: Eiffel Tower - N2 Plus
Replies: 15
Views: 5712

Re: Eiffel Tower - N2 Plus

Could you share the link for the Stl file
by Redron357
Thu Mar 02, 2017 10:57 pm
Forum: General
Topic: Weight of the 2N just the Printer
Replies: 7
Views: 2382

Re: Weight of the 2N just the Printer

yes thank you
by Redron357
Wed Mar 01, 2017 2:39 am
Forum: User's Gallery
Topic: Eiffel Tower - N2 Plus
Replies: 15
Views: 5712

Re: Eiffel Tower - N2 Plus

was this printed in one solid tower..
by Redron357
Wed Mar 01, 2017 1:44 am
Forum: General
Topic: Weight of the 2N just the Printer
Replies: 7
Views: 2382

Weight of the 2N just the Printer

I don't care about the shipping weight I have it now in my house, I was looking to purchase a table to sit it on and I need to know the printer weight. any one have any ideas

Go to advanced search