Search found 182 matches

by Spikeysonic
Thu Feb 28, 2019 11:54 pm
Forum: N Series
Topic: How do I extract worn out hex bolts from a N2dual top shroud and where do I get replacement screws please?
Replies: 4
Views: 176

Re: How do I extract worn out hex bolts from a N2dual top shroud and where do I get replacement screws please?

On that subject... I have a horrible feeling said superglu may have got behind the screw where it has its screw threads.

have got a n extraction kit only not sure how to use it especially with the cbale link connection in the way as its the two screws around that
by Spikeysonic
Wed Feb 27, 2019 12:01 am
Forum: N Series
Topic: How do I extract worn out hex bolts from a N2dual top shroud and where do I get replacement screws please?
Replies: 4
Views: 176

How do I extract worn out hex bolts from a N2dual top shroud and where do I get replacement screws please?

Im trying to go through tips from raise3D to prevent layer shifting (one which ejected the glass plate). One of the instructions is to lift off the top shroud to be able to get a look at the couplers to see if damged. However have come across a problem. 3 of the black top shroud screws (2mm hex) app...
by Spikeysonic
Tue Feb 05, 2019 12:14 am
Forum: Hardware
Topic: What Are serial errors and how would they be involed with prints going wrong after about 1 to 1.5cm model height
Replies: 4
Views: 298

Re: What Are serial errors and how would they be involed with prints going wrong after about 1 to 1.5cm model height

The screen freeze normally happens when trying to set things up or working, several minutes after starting to use the screen such as doing maintenance. Not so much mid print. It is very random. When things go wrong the print head usually continues either globby or shredded stringy or in these more r...
by Spikeysonic
Fri Feb 01, 2019 10:22 pm
Forum: Hardware
Topic: What Are serial errors and how would they be involed with prints going wrong after about 1 to 1.5cm model height
Replies: 4
Views: 298

Re: What Are serial errors and how would they be involed with prints going wrong after about 1 to 1.5cm model height

20190126_215250.jpg In this case When I came home my folks had switched off the printer and the floor was covered in broken glass with a big mess off 3d print handing down if I remember right. It was when all had been cleared up and I switched it on to run tests the serial message came up as attach...
by Spikeysonic
Fri Feb 01, 2019 2:19 am
Forum: Hardware
Topic: What on **** caused my N2 Dual the throw a new glass plate out of the closed door after 7 hours printing?
Replies: 8
Views: 564

Re: What on **** caused my N2 Dual the throw a new glass plate out of the closed door after 7 hours printing?

I used the 4 silver metal clips that came with the machine. 2 front 2 clips back. Whrn switched back on it mentioned serial error
by Spikeysonic
Thu Jan 31, 2019 10:58 pm
Forum: Hardware
Topic: What Are serial errors and how would they be involed with prints going wrong after about 1 to 1.5cm model height
Replies: 4
Views: 298

What Are serial errors and how would they be involed with prints going wrong after about 1 to 1.5cm model height

I have noticed several times prints that appear to be going fine after many hours (in this case 7ish) suddenly doing what appears to be a layer shift of a good few inches in 1 to 2 planes then shreading whats left all stingy or just a sudden layer shift. Ive also seen the term serial error come up s...
by Spikeysonic
Wed Jan 16, 2019 11:40 pm
Forum: Hardware
Topic: Filament add on sensor installation issues
Replies: 9
Views: 413

Re: Filament add on sensor installation issues

So as long as its a similar length ptfe tube, 6mm outer 4mm inner it will do? There is not an offical raise 3d 6mm outer 4mm inner tube with a set name so I dont go and get a 4mm one by accident? Will that be better for grippy materials like ninjaflex?
by Spikeysonic
Wed Jan 16, 2019 10:33 pm
Forum: Hardware
Topic: What on **** caused my N2 Dual the throw a new glass plate out of the closed door after 7 hours printing?
Replies: 8
Views: 564

What on **** caused my N2 Dual the throw a new glass plate out of the closed door after 7 hours printing?

I just purchased a Raise 3d replacement glass plate on Sunday after the one I had developed a clip which developed into a crack then split., Just got it and installed it yesterday, clipped it into place (it seemed thinner than the last one.) Did a tiny test print of a ring (Zero fil in the drop box)...
by Spikeysonic
Wed Jan 16, 2019 1:25 am
Forum: Hardware
Topic: Filament add on sensor installation issues
Replies: 9
Views: 413

Re: Filament add on sensor installation issues

Will a 6mm tube fit into a bondtech dual? and where in the uk would I get them?
by Spikeysonic
Tue Jan 15, 2019 2:19 am
Forum: Hardware
Topic: Filament add on sensor installation issues
Replies: 9
Views: 413

Re: Filament add on sensor installation issues

Id say no as they bearly reached the extruder when in the home position. coukd i replacevtgem with 6mm tubes? and coonect to a bind tech dual?
by Spikeysonic
Tue Jan 15, 2019 12:19 am
Forum: Hardware
Topic: Now do I NOT chip crack and split the glass plate
Replies: 1
Views: 248

Now do I NOT chip crack and split the glass plate

Now do I NOT chip crack and split the glass plate, Saw a crack bit on bottom that went half way then went all the way splitting it in two, it seemed to originate from one of the clamps, Original.

Costly replacement how do I not crack the next one in 2 please
by Spikeysonic
Tue Jan 15, 2019 12:16 am
Forum: Hardware
Topic: Filament add on sensor installation issues
Replies: 9
Views: 413

Re: Filament add on sensor installation issues

What about the long tubes that originally went from the screw in connectors above the filaments all the way to the bond tech or regular extruder. ? How is that connected or it is removed and the filament goes naked between the filament sensor to the extruders with no bowden tubes bar the little sens...
by Spikeysonic
Sun Jan 13, 2019 10:13 pm
Forum: Hardware
Topic: Filament add on sensor installation issues
Replies: 9
Views: 413

Filament add on sensor installation issues

Ive been trying to install the filament sensor only the instructions seem to be lacking... If it correct that you remove the Bowden tubes completely between the connectors able to spool and the print heads as the tubs that come with the sensor are very short. Why do I have a lead left over? what do ...
by Spikeysonic
Wed Nov 07, 2018 1:50 am
Forum: Hardware
Topic: How to Bondtec settigns differ to standard and does latests Ideamaker have bondtech settings Already?
Replies: 5
Views: 966

Re: How to Bondtec settigns differ to standard and does latests Ideamaker have bondtech settings Already?

d9d you wire the ribbon cable back and hot glue itbin placem You can get a free over heat protector. look in the hardware section. May be that
by Spikeysonic
Tue Oct 30, 2018 4:20 pm
Forum: Printing Settings
Topic: What are faster PLA settigns when using a Bond tech, how fast can you go?
Replies: 1
Views: 270

What are faster PLA settigns when using a Bond tech, how fast can you go?

I heard you can print PLA much faster with a Bond tech dual. Anyone got the faster settings... (all of them all pages) including infill, flow rate, heat, support, ooze etc

Thats speed, standard and high quality settings.

0.4mm nozzel but interested in settings with wider nozzel sizes
by Spikeysonic
Tue Oct 30, 2018 4:15 pm
Forum: N Series
Topic: Are PTFE feeding tubes worth the extra cash more than regular/ stock tubes
Replies: 3
Views: 429

Re: Are PTFE feeding tubes worth the extra cash more than regular/ stock tubes

Any UK suppliers? and what dimensions should I look for?
by Spikeysonic
Tue Oct 30, 2018 9:25 am
Forum: Hardware
Topic: How much better are ptfe feeding tubes from the spools than stock clear ones
Replies: 0
Views: 233

How much better are ptfe feeding tubes from the spools than stock clear ones

How much better are white PTFE feeding tubes from the spools than stock clear ones? Ive noticed my clear stock tubes appear grippy near the extruders. Thinking of replacing them but have seen the original clear ones about £5 and PTFE ones £13 however add £6 to the £5 for postage and not much differe...
by Spikeysonic
Tue Oct 30, 2018 9:21 am
Forum: Hardware
Topic: N2 Touchscreen not reacting to touch on it's left side
Replies: 18
Views: 2070

Re: N2 Touchscreen not reacting to touch on it's left side

Have noticed a tendancy for the touch screen to stop working after a while on an N2 Dual. Resetting it gets it working again but why does it stop working in the first place. Have tried taking off shows and socks, its on a thick wooded coffee table, on lino if that helps work things out earth wise

Go to advanced search