Search found 37 matches

by Ari
Sat Apr 13, 2019 7:08 am
Forum: N Series
Topic: Berd-Air -- no voltage to HE2 pin
Replies: 12
Views: 246

Re: Berd-Air -- no voltage to HE2 pin

I have a separate 12V PSU to supply the Pump. I will tie the 0V rail of the N2 to the 0V rail of the separate PSU and use the HE2 MOSFET to control the pump by switching the 0V line. I plan to set it up with minimal changes to the N2 to begin with, as I not convinced about the long term durability o...
by Ari
Fri Apr 12, 2019 8:21 am
Forum: N Series
Topic: Berd-Air -- no voltage to HE2 pin
Replies: 12
Views: 246

Re: Berd-Air -- no voltage to HE2 pin

Hi John, Good to know you have resolved the issue. Based on the tests you carried out on the MOSFET I had reached the conclusion that the HE2 pin of the CPU was not being driven by the firmware. Your explanation supports this, so all is good hardware wise. The MOSFETs used on the controller PCB are ...
by Ari
Tue Apr 09, 2019 9:03 pm
Forum: N Series
Topic: Berd-Air -- no voltage to HE2 pin
Replies: 12
Views: 246

Re: Berd-Air -- no voltage to HE2 pin

John Having seen your extensive N2 grades I suspect you are more than capable of locating the X axis faults and I not wish to appear to teach you to suck eggs but for what it’s worth I’ll throw my thoughts in the pot. They might or might not be useful. Treating the problems described in the posts ab...
by Ari
Mon Apr 08, 2019 6:04 am
Forum: N Series
Topic: Berd-Air -- no voltage to HE2 pin
Replies: 12
Views: 246

Re: Berd-Air -- no voltage to HE2 pin

John, I have just checked my own N2 Controller Board and confirmed that the positive pin of the HE2 output is tied to +24V and not 12V. Sorry this was my mistake. I have edited my previous post to reference 24V where appropriate to avoid misleading others reading the thread. The checks I have asked ...
by Ari
Sun Apr 07, 2019 9:58 pm
Forum: N Series
Topic: Berd-Air -- no voltage to HE2 pin
Replies: 12
Views: 246

Re: Berd-Air -- no voltage to HE2 pin

John *** EDITED to correct invalid reference to 12V ******** I note that you state the LED associated with HE2 is not illuminating when you command the output to turn ON. This is not related to the 24V rail. In my current thinking there could be 3 possible reasons for the LED not illuminating; a) So...
by Ari
Sat Apr 06, 2019 6:06 am
Forum: N Series
Topic: Berd-Air -- no voltage to HE2 pin
Replies: 12
Views: 246

Re: Berd-Air -- no voltage to HE2 pin

Hi John, Is it only the 12V from HE2 that is missing? Is the LED associated with the HE2 output working normally? Do you have 12V on any of the other ‘12V Outputs’? The reason I ask is that I am wondering if the 12V regulator has failed. We do not have the exact schematics for the Raise3D version of...
by Ari
Sun Mar 10, 2019 11:56 pm
Forum: Hardware
Topic: How I more than doubled my print speed while increasing accuracy
Replies: 15
Views: 817

Re: How I more than doubled my print speed while increasing accuracy

Wow John, that is pioneering at its best. Was that video in real time? What size nozzle were you using? Did you mill the extruder carrier out of aluminium or is it some other material? I and I'm sure others on the forum, are very keen to know more. It would be nice to see photos of the surface quali...
by Ari
Mon Jan 28, 2019 9:55 am
Forum: Pro2 Series
Topic: How to create 3D Print files with Live 3D Print Process support on the Touchscreen?
Replies: 14
Views: 464

Re: How to create 3D Print files with Live 3D Print Process support on the Touchscreen?

I'm using an older version of ideaMaker Ver.3.1.7.1850.

Only because I am working on a long project and do not want to introduce unexpected results part way through. Will update later.

Ari
by Ari
Sun Jan 27, 2019 5:06 pm
Forum: Pro2 Series
Topic: How to create 3D Print files with Live 3D Print Process support on the Touchscreen?
Replies: 14
Views: 464

Re: How to create 3D Print files with Live 3D Print Process support on the Touchscreen?

@phidon Third time lucky! I have just downloaded your files and tried them on my N2. Answer. No image is displayed on the touchscreen when printing. Neither is there a file icon image (only RAISE3D is shown). This was I think the same as you saw. However, I then downloaded the speed boat STL from Th...
by Ari
Wed Jan 02, 2019 4:24 pm
Forum: Pro2 Series
Topic: Broken Fan Duct
Replies: 2
Views: 165

Re: Broken Fan Duct

I do not have a Pro2 but I remember Vicky posting the attached STLs, could this be what you need?

Also check this link viewtopic.php?f=2&t=8&p=34452&hilit=shared#p34452

Ari
by Ari
Sat Dec 15, 2018 11:07 am
Forum: Hardware
Topic: Change dip switches to 1/2 step for extruder?
Replies: 2
Views: 232

Re: Change dip switches to 1/2 step for extruder?

@JohhSays Today is the first opportunity that I have had to reply, so you may well have already tried adjusting the microstepping function by now. I can only comment on your question "would it damage anything". The answer is no. Stepper motors are very tolerant devices provided you stay wi...
by Ari
Sun Oct 28, 2018 6:10 pm
Forum: Hardware
Topic: BABY STEPS - Z Tuning
Replies: 6
Views: 762

Re: BABY STEPS - Z Tuning

Unlikely we will see an update of Marlin now that the focus is on the Pro Series.
by Ari
Mon Oct 22, 2018 7:31 pm
Forum: Others
Topic: Drying filament under vacuum
Replies: 18
Views: 2709

Re: Drying filament under vacuum

Thanks for the update. I have been following this thread with interest. Have you found that the Nylon filament needs to be entirely free of moisture or is there a point where you have extracted sufficient moisture such that further drying has an insignificant effect on surface finish and part streng...
by Ari
Wed Sep 19, 2018 9:49 am
Forum: N Series
Topic: Silicone Hot End Covers anyone tried these?
Replies: 15
Views: 1248

Re: Silicone Hot End Covers anyone tried these?

@Spikeysonic

Try here;

https://3dgbire.com/products/hot-end-silicon-cover

Their website lists quite alot of spares for the N series and the new Pros.
by Ari
Tue Sep 04, 2018 6:44 pm
Forum: N Series
Topic: Silicone Hot End Covers anyone tried these?
Replies: 15
Views: 1248

Re: Silicone Hot End Covers anyone tried these?

One of the benefits of the hotend covers should be to prevent excess heat affecting the printed part as it prints, particularly where there are fine layers, for example at the top of a cone. There are some early posts somewhere on the forum with pictures that explain this better. Since I have not be...
by Ari
Sun Aug 12, 2018 11:27 am
Forum: Software
Topic: Stop print.... immediately!
Replies: 15
Views: 1709

Re: Stop print.... immediately!

@ABH
To further reiterate Jetguy's thanks, we all very much appreciate your work to improve the firmware and the fact that you are kind enough to share your efforts with our community. Also Jetguy as well, come to that, for his help and willingness to share his knowledge with us.

Ari
by Ari
Fri Aug 10, 2018 3:45 pm
Forum: User's Gallery
Topic: life size statue of Kara from "detroit become human" game
Replies: 7
Views: 1366

Re: life size statue of Kara from "detroit become human" game

Hi Pierre, Thank you for posting. Truely inspirational. The finish quality is superb. Would love to know more, e.g. the purpose of the project and how you achieved the high quality finish, particularly the face, (that is if you can share such details). Certainly shows what the N2 is capable of in th...
by Ari
Fri Jul 27, 2018 6:31 pm
Forum: General
Topic: Upgrade Components for N Series are Coming!
Replies: 14
Views: 2302

Re: Upgrade Components for N Series are Coming!

If Raise3D are limiting the upgrade components to the following items only; 1. BondTech Dual Extruder 2. BondTech Single Extruder 3. N Series Webcam 4. Hot End Silicon Cover (3pcs/set) How is it that 3d-drucker are advertising for sale in certain areas of Europe, all the parts required to build the ...
by Ari
Fri Jun 01, 2018 6:51 am
Forum: General
Topic: Glue for Raise3D PLA?
Replies: 6
Views: 1609

Re: Glue for Raise3D PLA?

@Jetguy and detroitus Thank you both for your quick responses and the useful links Jetguy. These gives me a good starting point. I am fortunate in that I have access to a fume cupboard and associated PPE if required. So I think some experimentation is needed. I will also give the Loctite 414 a go. R...
by Ari
Wed May 30, 2018 3:02 pm
Forum: General
Topic: Glue for Raise3D PLA?
Replies: 6
Views: 1609

Glue for Raise3D PLA?

Has anyone on the forum had experience of gluing together parts printed from Raise3D PLA (standard or premium)? I have tried Loctite superglue ( Ethyl 2 cyanoacrylate) but the bond is easily broken/ I am looking more for something where if forced, the PLA will give way before the glue bond. The part...

Go to advanced search