Official Raise3D Community

Hi Guys, With my fleet of Raise machines, I now how 3 different types of machines (N1, N2, Plus and Pro2), as well as other machines. One thing I would like to see introduced is the ability to assign an uploaded slice to a group. For example, upload myprint.gocde to the cloud then assign it to only ...

For the air gap, try 0.5mm, I use 0.46 for a 0.8mm nozzle, do some testing with 0.5-0.6 mm air gap with luck it should peel off with a little bit of effort.

I just received 20 sets of these clips and the freight was still more than them. Ah well. At least I have the spares now should I need them.

I have found a few of these screens for 29.00 AUD. I will buy what little stock they have left as another one looks like it is on its way out.

Hi Guys, Looking for a solution to fix my touchscreen, through hacking or finding a replacement screen only for it. The touch side still works its just that the screen has gone completely white. I had a look at a full replacement and $1,000 for one is just not going to happen. I did see that jetguy ...

Now, why was that so hard? Why cannot Raise 3D tech support just post or answer what the user asked for? Why jerk the user around and have them open a ticket and wait days for some moron of a technician to slowly spoon feed a reply? Oh sure, they want to sell you an overpriced cable, replace your b...

I just received my Bondtech (Direct from bondtech), It had 2 filaments in it, from what I can see it is there just to test that the extruder works as intended.

Hi Guys, I upgraded my early n2 plus to the bondtech extruders which have 140 steps per mm. I had to modify and create a new printer in ideamaker to do this. Can I do something similar in raise cloud? The other benefit of using ideamaker was that when i changed to a different printer setting that ha...

Hi Bajud, I print straight on to the glass bed, I found the build tak to be rubbish so I dont use it. Next check your z layer height to make sure it is the right distance from the plate. After that, print the first layer really slow, like 8 -12 mm/s making sure it gets a very good adhesion to the be...

the ribbon cable is a 14 wire cable. the question being is wither a better cable can be made using something like 24 AWG, 20 Conductor, Computer Cable, Foil Shield, but I guess that will depend on how big that wire is. someone with more electrical knowledge can likely determine the cable size neede...

I have 4 n2 plus machines, I would like to take part in the beta if possible.

Hi Vicky, This is what I was talking about with the remove printer option for all printers. I dont use the V1 hotend at all but it still populates as a selection. Same with a bunch of other printers. I would like to run my printer list nice and lean so Only the printer profiles that I use populate t...

Thanks for your updating! Did you meet the same problem when you install the previous versions? Not sure follow such installation steps, you will meet other problems next time installing other versions. No, this is the first time i have encountered this problem. All other times i have been able to ...

I was finally able to sort it out. First i went into regedit and exported the whole thing in case I stuffed it up, then I searched for all raise3d reference and deleted them. No good. What did work was I installed it on another computer copy and pasted it from the pc onto a usb stick, then copy pas...

I was finally able to sort it out. First i went into regedit and exported the whole thing in case I stuffed it up, then I searched for all raise3d reference and deleted them. No good. What did work was I installed it on another computer copy and pasted it from the pc onto a usb stick, then copy past...

HI Vicky, Just did that then, still did not work. Still comes up with the first pic and it is still showing in the remove software program. Would you like to share a screenshot of the registry key unde this path HKEY_CURRENT_USER\Software\Microsoft\Windows\CurrentVersion\Uninstall\ideaMaker? HI Vic...

HI Vicky,
Just did that then, still did not work. Still comes up with the first pic and it is still showing in the remove software program.

Here is the issue that I have in upgrading to the latest version, I cannot even install the current version. Basically, I cant reinstall ideamaker at all. ideamaker start.PNG When I click yes, that setup keeps appearing. When i go to remove programs you can clearly see that the program is still list...

I tried to unistall and reinstall the latest version, I have unistalled the first beta and when it goes to install the newer version it is asking for the first beta to be unistalled, I have looked in my system and I cant see any files relating to the original beta, and I can't find it in regedit eit...

Michael.P@Raise3D wrote:@Brad, I will make a note and pass it along to our software dev's, thank you for your input.

Thanks heaps.