Search found 58 matches

by budi67
Tue Aug 27, 2019 12:33 pm
Forum: Printing Settings
Topic: Top layer
Replies: 9
Views: 661

Re: Top layer

I have not tuned anything in advanced tab Here's the Chiron setting echo:Steps per unit: echo: M92 X80.00 Y100.00 Z400.00 E405.00 echo:Maximum feedrates (mm/s): echo: M203 X100.00 Y100.00 Z20.00 E80.00 echo:Maximum Acceleration (mm/s2): echo: M201 X350 Y350 Z50 E30000 echo:Accelerations: P=printing,...
by budi67
Mon Aug 26, 2019 1:49 pm
Forum: Printing Settings
Topic: Top layer
Replies: 9
Views: 661

Re: Top layer

It run under Marlin 2.0 Yes i have calibrate my extruder, I’ll check it again Let me ask another question, Can these defects be avoided? I have try solid fill rectillnear and lines, it's the same I have 0% infill overlap A big thanks ;) Ps : This print is not on the CoreXY, it's on the Chiron IMG_20...
by budi67
Fri Aug 23, 2019 7:20 am
Forum: Printing Settings
Topic: Top layer
Replies: 9
Views: 661

Re: Top layer

Ok, I have handed over all flowrate to 100%

the inner circles are not in the right dimensions

The files :

Bouton 1.gcode
(351.5 KiB) Downloaded 27 times

Bouton 1.data
(42.55 KiB) Downloaded 27 times


IMG_20190823_090936.jpg
by budi67
Thu Aug 22, 2019 5:00 am
Forum: Printing Settings
Topic: Top layer
Replies: 9
Views: 661

Re: Top layer

Here's the file :
Bouton 2.gcode
(334.89 KiB) Downloaded 37 times

Bouton 2.data
(42.56 KiB) Downloaded 28 times
by budi67
Wed Aug 21, 2019 2:27 pm
Forum: Printing Settings
Topic: Top layer
Replies: 9
Views: 661

Top layer

Hello all I have finished my CoreXY 500x500x500 in addition to my N2, i have try to print with Ideamaker. My extruder is properly calibrate. I have 0.92 in flowrate for this PLA I have set 120% for top layer but i still have gap, you can even see the bottom layer Which settings should I change? A bi...
by budi67
Tue May 01, 2018 2:17 pm
Forum: Software
Topic: Too much plastic at end of line
Replies: 7
Views: 1342

Re: Too much plastic at end of line

I have too Simplify3D, I am going to compare by printing the same part
by budi67
Tue May 01, 2018 2:13 pm
Forum: Software
Topic: Too much plastic at end of line
Replies: 7
Views: 1342

Re: Too much plastic at end of line

Thank Jetguy, i will translate and read this.
by budi67
Tue May 01, 2018 2:04 pm
Forum: Software
Topic: Too much plastic at end of line
Replies: 7
Views: 1342

Re: Too much plastic at end of line

Thanks for your answer, but the "coasting distance" is not only for the retracation point ?

I have just try with 1mm and no change to the solid layer (red on photo) but only at the retraction point (yellow on photo)
retract.PNG
by budi67
Tue May 01, 2018 1:28 pm
Forum: Software
Topic: Too much plastic at end of line
Replies: 7
Views: 1342

Too much plastic at end of line

Hello all

Sorry for my bad english
I have too much palstic at the end of line on solid layer
Can one modify it ? Last version of Ideamaker
Thanks

IMG_20180501_152205.jpg
by budi67
Mon Feb 05, 2018 7:19 pm
Forum: Software
Topic: Problem with retract
Replies: 5
Views: 1207

Re: Problem with retract

Thanks for the option, i will try this tomorrow.

No problem with the heating, but I am also going to verify
by budi67
Mon Feb 05, 2018 8:27 am
Forum: Software
Topic: Problem with retract
Replies: 5
Views: 1207

Re: Problem with retract

Here is an extract of the code ;Sliced by ideaMaker 3.1.0.1545, 2018-02-04 10:17:36 UTC+0100 ;Dimension: 410.000 410.000 400.000 0.400 ;Extruder Offset #1: 25.000 0.000 ;Filament Diameter #1: 1.750 ;Filament Diameter #2: 2.930 ;Filament Compensation #1: 94.00 ;Filament Compensation #2: 100.00 ;Filam...
by budi67
Sun Feb 04, 2018 8:59 am
Forum: Software
Topic: Problem with retract
Replies: 5
Views: 1207

Problem with retract

Hello I have bought a Creality CR10 as a supplement to N2. I have print a piece with Ideamaker but i have a problem with retract, the extrudeur retract on every begin and end lines. If a change the "retraction material amount" to 0, it's ok but i don't have any retraction I don't understan...
by budi67
Thu Feb 16, 2017 6:25 pm
Forum: Hardware
Topic: Extrudeur stepper driver voltage
Replies: 5
Views: 2674

Re: Extrudeur stepper driver voltage

Thanks for your answer !!! And thanks Jetguy for the guidance ;)
by budi67
Thu Feb 16, 2017 4:32 pm
Forum: Hardware
Topic: Extrudeur stepper driver voltage
Replies: 5
Views: 2674

Extrudeur stepper driver voltage

Hi,

I just have a question, what is the voltage for the 2 extrudeur stepper driver.

A big thanks,

Budi67
by budi67
Sat Feb 11, 2017 7:59 pm
Forum: Software
Topic: Question about preview
Replies: 8
Views: 2349

Re: Question about preview

I believe that one it is not understood, but it doesn't matter, thank you anyway.
I use a translator, it does not translate can be not correctly!!
by budi67
Sat Feb 11, 2017 6:26 pm
Forum: Software
Topic: Question about preview
Replies: 8
Views: 2349

Re: Question about preview

Thank you for your explanations Jetguy, very instructive.

I ahve test with 1 and 2 shell, it's OK, But how will be the outside aspect ? Unless reducing the speed for the exterior shell ?
by budi67
Sat Feb 11, 2017 2:23 pm
Forum: Software
Topic: Question about preview
Replies: 8
Views: 2349

Question about preview

Hi, I have a question about preview. Why at the base, I have 5 shell, but more I have a hole ? It's a preview bug or it are like that going to print ? Thanks Budi67 https://i37.servimg.com/u/f37/12/26/05/41/bas10.png https://i37.servimg.com/u/f37/12/26/05/41/haut10.png
by budi67
Tue Jan 24, 2017 5:49 am
Forum: Others
Topic: Members in France
Replies: 44
Views: 15600

Re: Members in France

Bonjour Laurent Je suis situé en Alsace, ça fait quelques mois que j'ai une N2, c'est ma 3e imprimante et celle-ci est la bonne !! J'en suis très content, surtout par rapport aux précédentes. Point de vue modif, j'ai mis le kit Bondtech, j'ai modifié la ventilation et je vais modifier le système pou...
by budi67
Sat Dec 24, 2016 8:50 am
Forum: Software
Topic: Circle not perfect
Replies: 14
Views: 3872

Re: Circle not perfect

Thnaks for your answer
I understand better now ;)
by budi67
Mon Dec 19, 2016 7:00 pm
Forum: Software
Topic: Circle not perfect
Replies: 14
Views: 3872

Re: Circle not perfect

Thank you for all this information
I would make various tests for even

Go to advanced search