Search found 10 matches

by danderson
Wed Sep 25, 2019 2:39 pm
Forum: General
Topic: Is Raise3d Premium PLA = Polymaker PolyLite PLA?
Replies: 0
Views: 131

Is Raise3d Premium PLA = Polymaker PolyLite PLA?

I recently starting using Polymaker PolyLite PLA on our Pro2 printers due to compatibility issues with other PLA types. Thanks to the Open Filament Program profile we are printing beautifully on the Pro2 printers (as well as our N2 plus). Upon studying the filament spools and the filament itself, I ...
by danderson
Thu Aug 01, 2019 8:48 pm
Forum: Pro2 Series
Topic: Ethernet connectivity issues - Pro2 does not connect, N2 plus does connect
Replies: 3
Views: 304

Re: Ethernet connectivity issues - Pro2 does not connect, N2 plus does connect

I have tried to match the settings on the printer with "Auto negotiation off" and no success.

I have tried auto negotiation on on the machine - no success.
by danderson
Thu Aug 01, 2019 8:44 pm
Forum: Pro2 Series
Topic: An end to jams - blowers are better...
Replies: 11
Views: 1597

Re: An end to jams - blowers are better...

I will add some thermal paste to see the impact on the performance. I have not tried a cold pull, but these printers are barely used. My early testing with Premium PLA filaments (Coex PLA Prime, Coex PLA pro, Raise3d Premium, Polymaker Polylite) show much better performance - even printing successfu...
by danderson
Thu Aug 01, 2019 8:42 pm
Forum: General
Topic: Poll - Do you use Ethernet, Wifi or Flash Drive to transfer your files to your Raise3D printer?
Replies: 51
Views: 8683

Re: Poll - Do you use Ethernet, Wifi or Flash Drive to transfer your files to your Raise3D printer?

All three printers have static IP addresses configured on the printers.

The most confusing part of this is that I get about 30-40 seconds of good connectivity, everything working, etc. before it craps out.
by danderson
Thu Jul 25, 2019 7:39 pm
Forum: Pro2 Series
Topic: An end to jams - blowers are better...
Replies: 11
Views: 1597

Re: An end to jams - blowers are better...

I am having severe symptoms of what I believe to be "heat creep" - print failures several hours into a print, only with 3rd party PLA, worse with the lid on, and worse on the left extruder than the right. The filament would stop extruding sporatically, missing layers or part of a layer, un...
by danderson
Wed Jul 24, 2019 3:44 pm
Forum: Pro2 Series
Topic: Ethernet connectivity issues - Pro2 does not connect, N2 plus does connect
Replies: 3
Views: 304

Ethernet connectivity issues - Pro2 does not connect, N2 plus does connect

Pro2 Printers: both are version 1.2.1.428, firmware 0-0-66 N2 plus printer: version 1.2.1.428, firmware 1.1.6-frs The Pro2 printers are having issues connecting by Ethernet to our school network. I will get a connection for 30-45 seconds where I can ping the printer, upload files, and connect via id...
by danderson
Wed Jul 24, 2019 3:38 pm
Forum: Pro2 Series
Topic: An end to jams - blowers are better...
Replies: 11
Views: 1597

Re: An end to jams - blowers are better...

I tried this mod, and I found that the left extruder improved greatly at the expense of the right extruder. The left extruder performance was almost as good as the right extruder was before with only a fan upgrade (10mm -> 20mm). Good mod if you really want to use the left exruder with PLA.
by danderson
Wed Jul 24, 2019 2:38 pm
Forum: User's Gallery
Topic: Mounting for End of Filament sensor
Replies: 1
Views: 839

Re: Mounting for End of Filament sensor

Second for this mod on my N2 Plus. Works great.
by danderson
Wed Jul 24, 2019 2:34 pm
Forum: General
Topic: Poll - Do you use Ethernet, Wifi or Flash Drive to transfer your files to your Raise3D printer?
Replies: 51
Views: 8683

Re: Poll - Do you use Ethernet, Wifi or Flash Drive to transfer your files to your Raise3D printer?

tl;dr: IT department forced connection speed on the managed switch to 100Mbit/full duplex, ethernet now works great on Pro2. I had been battling this Pro2 ethernet issue for a while. The IT department at my school was convinced that the problem was not on their end, but I had no idea. I have the la...
by danderson
Fri Jul 19, 2019 10:36 pm
Forum: General
Topic: Poll - Do you use Ethernet, Wifi or Flash Drive to transfer your files to your Raise3D printer?
Replies: 51
Views: 8683

Re: Poll - Do you use Ethernet, Wifi or Flash Drive to transfer your files to your Raise3D printer?

tl;dr: IT department forced connection speed on the managed switch to 100Mbit/full duplex, ethernet now works great on Pro2. I had been battling this Pro2 ethernet issue for a while. The IT department at my school was convinced that the problem was not on their end, but I had no idea. I have the las...

Go to advanced search