Search found 106 matches

by RiserDog
Wed Jul 10, 2019 7:25 pm
Forum: Hardware
Topic: Gantry not smooth in area
Replies: 5
Views: 251

Re: Gantry not smooth in area

Thank you for the reply. Interesting diagnosis. What do those 2 couplers do? How certain are you that the 2 couplers are the cause of the binding? Also, where can I get a set as they are not on the Raise web site.
by RiserDog
Wed Jul 10, 2019 6:10 pm
Forum: Hardware
Topic: Gantry not smooth in area
Replies: 5
Views: 251

Re: Gantry not smooth in area

Do you mean the 2 couplers for the Z axis? Are they in the bottom of the machine below a metal plate?
by RiserDog
Mon Jul 08, 2019 11:44 pm
Forum: Hardware
Topic: Gantry not smooth in area
Replies: 5
Views: 251

Gantry not smooth in area

I have a Pro that is 8 months old. Recently it makes a loud binding sound when the print head is over a corner of the print bed (about 1/4 of the print bed). I greased up the rails with PTFE grease twice and this did not help. I can move the print head around by hand and I can tell it is more diffic...
by RiserDog
Sat Jun 01, 2019 4:56 pm
Forum: General
Topic: Need a strong material to make a Buckle Snap
Replies: 3
Views: 698

Need a strong material to make a Buckle Snap

Just wondering if anyone has printed those snap buckles that are on backpacks? Did you go with nylon? It needs to be stiff yet has to bend a little to work so not sure what material is best. Thanks. :)
by RiserDog
Tue May 28, 2019 7:12 pm
Forum: Hardware
Topic: Better placement of the filament sensor
Replies: 2
Views: 276

Better placement of the filament sensor

I have had my Pro2 since December and nearly every time I change the filament I have to take off the filament sensor. This is because as I remove the filament a blob is created at the end. Off goes the sensor so I can snip off the end. Nearly every time!!! If the sensor was on the frame of the print...
by RiserDog
Wed Mar 13, 2019 4:42 pm
Forum: Pro2 Series
Topic: First dual color print question
Replies: 1
Views: 265

First dual color print question

I am doing a dual color print and it looks fairly good. It would be better if I could get the right nozzle to stop oozing so much when it is not printing. The left nozzle doesn't ooze very much. I have an ooze shield around the entire print but some of the ooze gets onto the main print. Both nozzles...
by RiserDog
Sat Mar 02, 2019 2:11 pm
Forum: Pro2 Series
Topic: Other .2 nozzles that will work
Replies: 1
Views: 290

Other .2 nozzles that will work

I use a .2mm nozzle a lot. The one I received from Raise lasted about 30 prints and now it seems to be shot. I cleaned it thoroughly and still not working correctly. Does anyone know if N2 nozzles or any other brand nozzles work on the PROs? :P
by RiserDog
Thu Feb 28, 2019 9:01 pm
Forum: Pro2 Series
Topic: Does the Pro have a teflon tube before hot end
Replies: 2
Views: 363

Does the Pro have a teflon tube before hot end

Wondering if the Pro is an all metal hotend or does it have a teflon tube? I know my N2 plus has a teflon tube. When I am loading the filament it seems to hit something near the hot end. thanks. :geek:
by RiserDog
Fri Feb 01, 2019 3:43 pm
Forum: Feature requests, ideas, wishes
Topic: Nozzle Tracker
Replies: 1
Views: 332

Nozzle Tracker

It would be cool if I could input when I changed a nozzle and be able to see that date on the home screen. I currently use a sticker on the machine and hand write it down. It would need to be on the home screen so you don't have to flip around to find it. :ugeek:
by RiserDog
Fri Jan 18, 2019 4:40 pm
Forum: Pro2 Series
Topic: Removing the HEPA filter
Replies: 2
Views: 293

Removing the HEPA filter

Hey is there a trick to getting the HEPA filter out? Just doesn't want to get out by pulling the tab. I want to save it for ABS printing. :)
by RiserDog
Tue Jan 15, 2019 4:07 pm
Forum: Pro2 Series
Topic: Fan shroud
Replies: 1
Views: 289

Fan shroud

Was wondering if Raise could send some info on the Fan shroud and fan used for the N2 single. The larger shroud on the right side of the hotend. I am considering putting one onto the Pro2 on the right side. Thanks! :?
by RiserDog
Fri Jan 11, 2019 4:01 pm
Forum: Pro2 Series
Topic: Beneath Supports is rougher than N1
Replies: 3
Views: 353

Re: Beneath Supports is rougher than N1

I updated the 2 firmwares before printing anything. I only use Simplify3d for slicing so I could send those profiles if you can use those. Have your tests shown any difference between the N2 and Pro2 as far as how undersides of supports look? Again I have a single nozzle N2.
by RiserDog
Thu Jan 10, 2019 12:17 am
Forum: Pro2 Series
Topic: Beneath Supports is rougher than N1
Replies: 3
Views: 353

Beneath Supports is rougher than N1

I have a N1 plus single nozzle and the it prints parts with supports very well. The supports come off easily and the underside is fairly smooth as can be seen in the right image. The Pro2 does not do as well. The first layer atop the supports will have gaps in it and the supports are more difficult ...
by RiserDog
Mon Jan 07, 2019 7:34 pm
Forum: Pro2 Series
Topic: Turning off the HEPA filter
Replies: 3
Views: 405

Turning off the HEPA filter

Is there a way to turn off the HEPA filter on the Pro2? I have the top lid open when I print PLA so the filter is not really helping clean the air. thanks. :P
by RiserDog
Thu Jan 03, 2019 11:27 pm
Forum: Software
Topic: Turning Right nozzle OFF at startup
Replies: 2
Views: 274

Re: Turning Right nozzle OFF at startup

thanks for the reply.
by RiserDog
Thu Jan 03, 2019 9:34 pm
Forum: Software
Topic: Turning Right nozzle OFF at startup
Replies: 2
Views: 274

Turning Right nozzle OFF at startup

Just got a Raise Pro2 and just got the first print running. It is working well on the left nozzle but I had to manually turn off the Right nozzle. I use Simplify3d and I used the preset profile and turned everything to zero for the right nozzle. When the machine starts up "both" nozzles an...
by RiserDog
Fri Oct 12, 2018 5:31 pm
Forum: Pro2 Series
Topic: Can a Glass Bed be added to the Pro Series
Replies: 5
Views: 760

Re: Can a Glass Bed be added to the Pro Series

Thanks. Did you adhere the glass to the build plate somehow or do the thermal pads adhere the glass? What is the reason for the thermal pads?
by RiserDog
Thu Oct 11, 2018 4:01 pm
Forum: Pro2 Series
Topic: Can a Glass Bed be added to the Pro Series
Replies: 5
Views: 760

Can a Glass Bed be added to the Pro Series

Can a glass bedplate be added to the Pro Series? Maybe use one off of a N2. I find the Buildtak leaves a white residue when printing some colors of pla. :roll:
by RiserDog
Tue Jul 03, 2018 8:25 pm
Forum: General
Topic: Should the motion controller firmware and touchscreen firmware be updated
Replies: 1
Views: 412

Should the motion controller firmware and touchscreen firmware be updated

I have a 2 year old N2+. Not sure if I need to update all of these firmwares. Wondering if issues have occured with poeple upgrading older machines to the latest firmwares.... or are they fairly safe.
by RiserDog
Tue Jul 03, 2018 7:54 pm
Forum: General
Topic: Printing with PolyCarbonate
Replies: 5
Views: 1258

Re: Printing with PolyCarbonate

hey Zemlin,
Can you post a picture of something you printed with ePC on the raise? I would like to see the complexity level. Thanks for all of the comments!

Go to advanced search