Search found 19 matches

by schuema
Fri Dec 18, 2020 7:34 am
Forum: Software
Topic: ideaMaker 4.0.1 Release Notes
Replies: 20
Views: 4623

Re: ideaMaker 4.0.1 Release Notes

Hello,

any idea for my problem ?

Best regards

Martin
by schuema
Wed Dec 16, 2020 10:33 am
Forum: Software
Topic: ideaMaker 4.0.1 Release Notes
Replies: 20
Views: 4623

Re: ideaMaker 4.0.1 Release Notes

I think you must change the values top layer 3 and 1 surface. That's it. Surface are the last layers of the print object. So I have no problems with printing.I think it's misunderstanding in your case ;-) If that is not your problem, deinstall all, clear the config folder from ideamaker and the inst...
by schuema
Mon Dec 14, 2020 4:29 pm
Forum: Software
Topic: ideaMaker 4.0.1 Release Notes
Replies: 20
Views: 4623

ideaMaker 4.0.1 Bug

Hi there, I discovered the following bug in the new release of ideamaker. When I set the settings in the materials, which are normally only available once in the profiles, the value that is smallest is always used. That made a lot of sense to me in terms of the heating bed temperature and speeds. I ...
by schuema
Fri Oct 23, 2020 10:17 am
Forum: Software
Topic: ideaMaker 4.0.0-Beta Release Notes
Replies: 27
Views: 2796

Re: ideaMaker 4.0.0-Beta Release Notes

Vicky@Raise3D wrote:Can you run appimage file in terminal and share a screenshot of the error message?

I must do a reset of my PC, because however I had xubuntu 20.10 beta on my machine. After fresh installation of 20.04 it works fine.
Thank you for your work an help.
by schuema
Fri Oct 16, 2020 7:50 am
Forum: Software
Topic: ideaMaker 4.0.0-Beta Release Notes
Replies: 27
Views: 2796

Re: ideaMaker 4.0.0-Beta Release Notes

Hello,
cool a new version, but it does not work on Linux, not the DEB- and not the APPIMAGE-file. I'm working on xubuntu 20.04

Any idea?

Best regards
by schuema
Tue Jul 21, 2020 6:56 am
Forum: Printing Settings
Topic: Raise3D ABS + XY Size compensation
Replies: 24
Views: 8278

Re: Raise3D ABS + XY Size compensation

Perfect! You really do a good job. I love your work and the slicer ;-)
by schuema
Fri Jul 17, 2020 1:50 pm
Forum: Printing Settings
Topic: Raise3D ABS + XY Size compensation
Replies: 24
Views: 8278

Re: Raise3D ABS + XY Size compensation

No, I didn't I thought Vicky@raise reads the posts also here ;-)
@Vicky@Raise3D : Did you?
by schuema
Fri Jul 17, 2020 1:44 pm
Forum: Software
Topic: Printing with two nozzles only one makes a wipe tower
Replies: 4
Views: 806

Re: Printing with two nozzles only one makes a wipe tower

Perfect. Thank you for the help
by schuema
Wed Jul 15, 2020 8:14 am
Forum: Printing Settings
Topic: Raise3D ABS + XY Size compensation
Replies: 24
Views: 8278

Re: Raise3D ABS + XY Size compensation

@leonhard8888: Sure, I do it also, but sometimes I forgot it. And so it will be great when I can store in the template. But your idea is a workaround
by schuema
Wed Jul 15, 2020 8:11 am
Forum: Software
Topic: Printing with two nozzles only one makes a wipe tower
Replies: 4
Views: 806

Re: Printing with two nozzles only one makes a wipe tower

Sure! Here they are
GummiTest.gcode
Gcode
(358.83 KiB) Downloaded 59 times

GummiTest.idea
Idea
(56.78 KiB) Downloaded 61 times

GummiTest.data
Data
(52.77 KiB) Downloaded 59 times
by schuema
Tue Jul 14, 2020 3:57 pm
Forum: Software
Topic: Printing with two nozzles only one makes a wipe tower
Replies: 4
Views: 806

Printing with two nozzles only one makes a wipe tower

Hello!

I print with two nozzles, but only one nozzle creates a wipeTower. However, the second nozzle does not print an entire layer. If you print an entire layer, it will also create a wipe tower layer. Any idea or is it a bug?

See my screenshot!
Bildschirmfoto_2020-07-14_17-56-08.png
Screenshot
by schuema
Tue Jul 14, 2020 8:51 am
Forum: Printing Settings
Topic: Raise3D ABS + XY Size compensation
Replies: 24
Views: 8278

Re: Raise3D ABS + XY Size compensation

I would like to take up the topic again. The compensation e.g. ABS or ASA would be better as a percentage. Because usually you have e.g. a shrinkage of 2% and not an absolute size. You should also consider a dual printer, so it would be better to be able to make this setting for each extruder, becau...
by schuema
Mon Jul 13, 2020 2:34 pm
Forum: Printing Settings
Topic: Different speeds with dual prints
Replies: 12
Views: 3151

Re: Different speeds with dual prints

I would like to take up the topic again. It would be really good if you had the corresponding profiles per filament available with a dual printer per extruder and filament. As an example, I just want to combine a PLA print with TPE32. here it essentially differs in speed. I can only do this with gro...
by schuema
Fri Apr 26, 2019 2:27 pm
Forum: Software
Topic: ideaMaker 3.4.0-Beta Release Notes Updated Rev. 3.4.0.2855-Beta, 2019.04.04
Replies: 41
Views: 9911

Re: ideaMaker 3.4.0-Beta Release Notes Updated Rev. 3.4.0.2855-Beta, 2019.04.04

Hello, I just use the new Beta and I'm happy that's my problem with the preview is solved if the system local settings are europe not english or US under the operation system linux. But now I've a new problem. I have a use for a flower pot in cone shape designed not only the shell but solid. Now I s...
by schuema
Thu Mar 14, 2019 7:59 pm
Forum: Software
Topic: Gcode preview looks wrong in Ubuntu
Replies: 32
Views: 9092

Re: Gcode preview looks wrong in Ubuntu

the problem ist the number format:

English: 1,000,000.00€
German: 1.000.000,00€

Perhaps you can correct it with the next release.
by schuema
Thu Mar 14, 2019 7:54 pm
Forum: Software
Topic: Gcode preview looks wrong in Ubuntu
Replies: 32
Views: 9092

Re: Gcode preview looks wrong in Ubuntu

Now I checked again. The problem ist not the language setting. The problem is the language special formats. I've the interface switched to english and now the formats to german and I've the problem again. But when I switch back to english too, it works. Perhaps it helps to correct the error at the s...
by schuema
Wed Mar 13, 2019 5:39 pm
Forum: Software
Topic: Gcode preview looks wrong in Ubuntu
Replies: 32
Views: 9092

Re: Gcode preview looks wrong in Ubuntu

We are so sorry about the trouble. We do have tested on a few Linux computer we have on computer, but unfortunately we can't recreate the same issue to debug. Would you mind to provide us the configuration of your computer? You can find some graphic card and driver information from the following li...
by schuema
Thu Feb 28, 2019 7:38 am
Forum: Software
Topic: Gcode preview looks wrong in Ubuntu
Replies: 32
Views: 9092

Re: Gcode preview looks wrong in Ubuntu

I'm sad there is no solution for Linux Users since all the years, more then a year. Is there a new release in plan? I'm very happy with your slicer, it makes a great job but a good preview is necessary to avoid errors before print.
by schuema
Tue Feb 05, 2019 4:18 pm
Forum: Software
Topic: Gcode preview looks wrong in Ubuntu
Replies: 32
Views: 9092

Re: Gcode preview looks wrong in Ubuntu

Hello,

I've the same problem. Did anyone find a solution. I use also Ubuntu 18.04.1

Thank's for the great slicer.

Best regards
schuema

Go to advanced search