Search found 10 matches

by Fortross
Mon Jan 13, 2020 10:50 am
Forum: Hardware
Topic: The temperature of an extruder and a table loses in the middle of printing
Replies: 4
Views: 1505

Re: The temperature of an extruder and a table loses in the middle of printing

I installed the latest RaiseTouch, but unfortunately, after a few days of experimenting, I haven't been able to catch the moment when it stops extruding plastic. Though I have no logs for you. Moreover, after checking connections on the board and those wires from thermocouples and hotends the proble...
by Fortross
Thu Jan 09, 2020 8:23 am
Forum: Hardware
Topic: The temperature of an extruder and a table loses in the middle of printing
Replies: 4
Views: 1505

Re: The temperature of an extruder and a table loses in the middle of printing

Yes, ok, I will do that. I didn't see what the temperature was, but the log on the printer screen shows the temperature of the right (working) extruder has dropped down to around 70 degrees and then rising up to the normal temp. The model was printed in dual extrusion mode, at the point of temp drop...
by Fortross
Sat Jan 04, 2020 3:46 am
Forum: Hardware
Topic: The temperature of an extruder and a table loses in the middle of printing
Replies: 4
Views: 1505

The temperature of an extruder and a table loses in the middle of printing

Actually, I have an issue. The temperature of the extruder and the table drops down while printing which causes failed prints. The LOG file is attached. The support ticket was sent, but I didn't receive an answer. I appreciate your help.
by Fortross
Tue Jan 08, 2019 2:06 pm
Forum: Hardware
Topic: Another topic about a gap
Replies: 13
Views: 2753

Re: Another topic about a gap

Well, the question is settled.

Zemlin's link was decisive, thank you very much! There was just overheating problem working with ASA. I made some changes and printed absolutely good parts without any warping at all.

So, the printer is OK. My apologies for the disturbance.
by Fortross
Wed Dec 26, 2018 2:07 pm
Forum: Hardware
Topic: Another topic about a gap
Replies: 13
Views: 2753

Re: Another topic about a gap

I'm running ASA without layer cooling at all. For the nozzle cooler, I printed a deflector to avoid any atmosphere movement next to the model.

Anyway, thank you for your attention paid and for the info. I'll go on searching for the solution. It should be somewhere.
by Fortross
Wed Dec 26, 2018 8:22 am
Forum: Hardware
Topic: Another topic about a gap
Replies: 13
Views: 2753

Re: Another topic about a gap

Unfortunately, the Hatchbox doesn't produce ASA and isn't introduced to the EU market, but we do have eSUN filament here, thanks, I'll try it. I invested some money in buying different filament - Fillamentum, Zortrax, and eSUN, which I ordered yesterday on the basis of your experience. I'll try all ...
by Fortross
Mon Dec 24, 2018 3:50 pm
Forum: Hardware
Topic: Another topic about a gap
Replies: 13
Views: 2753

Re: Another topic about a gap

If you'd like to take a video which can see the abnormal you can see and share with our technician at http://help.raise3d.com, they can help diagnose. I'll try to make the video in short time. Thanks for your respond, zemlin. To be honest, I just try to figure out if there is something wrong with t...
by Fortross
Sat Dec 22, 2018 12:59 am
Forum: Hardware
Topic: Another topic about a gap
Replies: 13
Views: 2753

Re: Another topic about a gap

I didn't mean these rods wiggle really "a lot", there is some wiggling which is enough to obtain unconstant gap. It's hard to diagnose these rods while they're mounted. I'm thinking about examination in laboratory conditions. It will cost some money, but then I'll understand if they aren't...
by Fortross
Fri Dec 21, 2018 9:42 am
Forum: Hardware
Topic: Another topic about a gap
Replies: 13
Views: 2753

Re: Another topic about a gap

Yes, there is some resistance when moving the printhead around. About playing... Yes, they play. It's pretty obvious to see with the naked eye. And all of this is not about bearings or untighten screws, I revised all of them.
by Fortross
Thu Dec 20, 2018 6:18 pm
Forum: Hardware
Topic: Another topic about a gap
Replies: 13
Views: 2753

Another topic about a gap

Hello everyone. I've recently bought the brand new Raise3D Pro2 with a dual extruder set. I bought this printer for purposes of prototyping and low series manufacturing. Material - ASA with HIPS as a support. The problem is trivial - warping of a model. Yes, I've searched community forum trying to f...

Go to advanced search