Search found 37 matches
- Sat Jul 20, 2019 9:10 am
- Forum: Pro2 Series
- Topic: Make the Pro2 Silent (agian) ;)
- Replies: 10
- Views: 3187
Re: Make the Pro2 Silent (agian) ;)
i can also recommend Arctic TC (temperature controlled) fans. 500 rpm idle. linear speed increase when sensor hits 32C (89.6F) ARCTIC F12 TC ARCTIC F12 PRO TC IDEAL TEMPERATURE CONTROL: The temperature sensor is on a 40 cm cable and can be placed in the warm areas of your computer. This assures temp...
- Thu Jul 26, 2018 9:47 am
- Forum: Pro2 Series
- Topic: the temperature of the motors overheat the extruder unit
- Replies: 21
- Views: 6457
Re: the temperature of the motors overheat the extruder unit
just to be safe, i plan to print two of these and connect to LED3 and LED4 connectors on extruder connection board.
NEMA 17 40mm fan mount: https://www.thingiverse.com/thing:259718
Nema 17 cooler: https://www.thingiverse.com/thing:244292
are those LED3/LED4 connectors controllable by gcode?
NEMA 17 40mm fan mount: https://www.thingiverse.com/thing:259718
Nema 17 cooler: https://www.thingiverse.com/thing:244292
are those LED3/LED4 connectors controllable by gcode?
- Thu Jul 26, 2018 9:35 am
- Forum: Pro2 Series
- Topic: Solved : overheating , Jams , fail Prints , stuck Pro2
- Replies: 35
- Views: 10743
Re: Solved : overheating , Jams , fail Prints , stuck Pro2
i had no trouble so far but than again, i only used raise3d and polymaker filaments.
(polymaker jamfree: https://www.youtube.com/watch?v=06msIb4PWkU)
@Vicky@Raise3D:
better be safe than sorry, so should we apply this mod to our printers ourselves ?
(polymaker jamfree: https://www.youtube.com/watch?v=06msIb4PWkU)
@Vicky@Raise3D:
better be safe than sorry, so should we apply this mod to our printers ourselves ?
- Fri Jul 06, 2018 12:55 pm
- Forum: General
- Topic: Pro2 HEPA Filter control
- Replies: 3
- Views: 1619
Pro2 HEPA Filter control
is Pro2's HEPA filter software controllable?
i'm printing PLA and my cover is already open so filter fan is just an additional noise.
i'm printing PLA and my cover is already open so filter fan is just an additional noise.
- Tue Jan 30, 2018 12:57 pm
- Forum: Software
- Topic: ideaMaker 3.1 - MAC - download fail
- Replies: 3
- Views: 1151
ideaMaker 3.1 - MAC - download fail
trying to download the ideaMaker 3.1 dmg from https://www.raise3d.com/pages/download <Code>AccessDenied</Code> <Message>Access Denied</Message> <RequestId>EC4E7BBDC4E103F0</RequestId> <HostId> CPrRHuW6VNntYZKssCjtuTuXQGd5m6Rs6M+H055LvhuA+qUhapj78J4Hx1wIJuNKhhr/fzG/8fw= </HostId> </Error>
- Thu Jan 26, 2017 3:06 pm
- Forum: Feature Requests, Ideas, Wishes
- Topic: IdeaMaker mac fixes.
- Replies: 15
- Views: 4470
- Sat Jan 21, 2017 6:27 pm
- Forum: Feature Requests, Ideas, Wishes
- Topic: IdeaMaker mac fixes.
- Replies: 15
- Views: 4470
Re: IdeaMaker mac fixes.
note: i don't know if this is a mac only issue or a general one.
for some models, ideamaker complains that they are not valid. we can repair them but if the model is a complex one, ideamaker never finishes repairing. (osx sierra, i7, 16gb)
e.g.: https://www.thingiverse.com/thing:392804
for some models, ideamaker complains that they are not valid. we can repair them but if the model is a complex one, ideamaker never finishes repairing. (osx sierra, i7, 16gb)
e.g.: https://www.thingiverse.com/thing:392804
- Wed Jan 04, 2017 5:41 pm
- Forum: General
- Topic: Make: FFF printer test scores
- Replies: 14
- Views: 4783
Re: Make: FFF printer test scores
- Tue Jan 03, 2017 10:04 pm
- Forum: General
- Topic: Make: FFF printer test scores
- Replies: 14
- Views: 4783
Re: Make: FFF printer test scores
back when i bought gizmo dorks' pei, they didn't come with adhesive tape. i bought my 3m 468mp from tapecase (tapecase.com) the pei sheet was not cut perfectly so i had to file down the edges to make it flat. then cleaned it with ipa before sticking the tape. please note that these PEI sheets does n...
- Tue Jan 03, 2017 8:35 pm
- Forum: General
- Topic: Make: FFF printer test scores
- Replies: 14
- Views: 4783
Re: Make: FFF printer test scores
quality wise both printers are great. one of my printers is rostock g2s delta. it was painful to calibrate and sometimes it gets confused and can't print in straight line. but when it prints, it prints fast and great. prusa mk2 hotend is e3d v6. it's a great hotend. spare parts are available everywh...
- Tue Jan 03, 2017 8:10 pm
- Forum: General
- Topic: Make: FFF printer test scores
- Replies: 14
- Views: 4783
Re: Make: FFF printer test scores
i worked back and forth slowly so it was bubble free but i was not patient enough so creases were inevitable. but no issues when printing. since the adhesive and pei are separate, was it difficult to apply it w/o bubbles or creases? thanks! please note that these PEI sheets does not cover the glass ...
- Tue Jan 03, 2017 5:24 pm
- Forum: General
- Topic: Make: FFF printer test scores
- Replies: 14
- Views: 4783
Re: Make: FFF printer test scores
please note that these PEI sheets does not cover the glass edge to edge. Glass: N series Spare Parts - High Temperature Build Plate PEI: Gizmo Dorks PEI Sheet, 12" x 12" 3D Printing Build Surface with 3M 468MP Adhesive Tape (this is the one i'm currently using on Raise3D but it's thicker t...
- Sat Dec 31, 2016 6:42 pm
- Forum: General
- Topic: Make: FFF printer test scores
- Replies: 14
- Views: 4783
Re: Make: FFF printer test scores
i have both raise3d n2v2 and prusa i3mk2 (and 7 others).. ideamaker: Config IdeaMaker with Other Printers (settings for simplify3d, cura, kisslicer are available on prusa site. i use simplify3d) abs: a lot of people print without enclosure but i've never tried it. i use raise3d for abs. (i replaced ...
- Sat Dec 31, 2016 11:05 am
- Forum: General
- Topic: Make: FFF printer test scores
- Replies: 14
- Views: 4783
- Tue Nov 22, 2016 9:58 am
- Forum: Software
- Topic: ideaMaker 2.3.0 Release Note 2016.11.21
- Replies: 35
- Views: 12521
Re: ideaMaker 2.3.0 Release Note 2016.11.21
thank you.
Vicky@Raise3D wrote:Please try again. We have fixed it.
- Tue Nov 22, 2016 7:45 am
- Forum: Software
- Topic: ideaMaker 2.3.0 Release Note 2016.11.21
- Replies: 35
- Views: 12521
Re: ideaMaker 2.3.0 Release Note 2016.11.21
when i try to download the mac version, i get Access Denied error.
Code: Select all
<Error>
<Code>AccessDenied</Code>
<Message>Access Denied</Message>
...
- Tue Nov 22, 2016 5:59 am
- Forum: General
- Topic: Raise3D N2+ 3D Printer Review - 3D Printing Nerd
- Replies: 0
- Views: 2205
Raise3D N2+ 3D Printer Review - 3D Printing Nerd
I was finally able to get my official review thoughts about the Raise3D N2+ 3d printer shot, edited, produced, and published! The fine folks at Raise3D provided this printer for me for review. As with all reviews, this is unbiased and the opinions I state are based on my experience with the printer...
- Sun Sep 04, 2016 11:28 am
- Forum: General
- Topic: 3D Printing Fail (and lessons to be learned)
- Replies: 3
- Views: 2146
3D Printing Fail (and lessons to be learned)
3d printing is still more art than science. I was printing a Pokeball from Pokemon for my friend and her sons. What happened is best described as an epic failure. Here is what happened and how I fixed it! Also, the Raise3D N2+ was incredibly easy to fix, even though it was my own stupidity that bro...
- Mon Aug 08, 2016 4:45 pm
- Forum: General
- Topic: 3D Printing Nerd: Raise3D N2+ Unboxing and First Use
- Replies: 9
- Views: 3908
Re: 3D Printing Nerd: Raise3D N2+ Unboxing and First Use
The unboxing of the Raise3D N2+ 3d printer left me, and most of you, wanting more. I've got the printer printing, and just a small issue to work out before I can consider it ready to go for long prints. Here I update you on the printer, address the build plate clips issue, and apparently stay up wa...
- Fri Aug 05, 2016 5:14 pm
- Forum: General
- Topic: 3D Printing Nerd: Raise3D N2+ Unboxing and First Use
- Replies: 9
- Views: 3908
3D Printing Nerd: Raise3D N2+ Unboxing and First Use
The Raise3D printers are quite a sight to be seen, and the N2+ is easily the biggest enclosed 3D printer I've ever unboxed and used. The box comes on it's own pallet. Crazytown. In this video I unbox the printer and attempt to put it through it's first use. What happens? Watch and find out! https:/...