Search found 85 matches

by Proschi3d
Fri Jan 15, 2021 12:53 pm
Forum: Software
Topic: Gcode syntax for E2
Replies: 20
Views: 423

Re: Gcode syntax for E2

Good Prusa profile, thank you

What I also changed in the Gcode is, I move 50 mm away in X quickly to the side before printing starts, in order to avoid that it takes extruded material into the part
by Proschi3d
Fri Jan 15, 2021 8:12 am
Forum: E2
Topic: Which stepper motors are installed?
Replies: 4
Views: 73

Re: Which stepper motors are installed?

Steven@Raise3D wrote:The motors that we use are a classic NEMA style stepper motor. Unfortunately, we do not have any type of datasheets available for the motors that we use in our machines.


How should a device work properly if I don't know what to install?
by Proschi3d
Fri Jan 15, 2021 5:32 am
Forum: E2
Topic: Which stepper motors are installed?
Replies: 4
Views: 73

Re: Which stepper motors are installed?

how could that know besides you?
by Proschi3d
Thu Jan 14, 2021 6:33 pm
Forum: E2
Topic: Duet Motionboard firmware
Replies: 1
Views: 33

Duet Motionboard firmware

Is it possible to install a current Duet wifi firmware on the Motionboard? Currently there is a very old firmware on it. I think the breaks that many people have in printing are due to a small buffer. The current Duet firmware uses a larger buffer
by Proschi3d
Wed Jan 13, 2021 1:33 pm
Forum: E2
Topic: E2 Paused printing
Replies: 16
Views: 317

Re: E2 Paused printing

modiug wrote:I agree with you all.
My curiosity is: is it possible that there is not an American with this problem?
GM


is probably rather unlikely.
Have you already tried something to fix the error?
should we open a thread that has already been tried?
by Proschi3d
Wed Jan 13, 2021 9:28 am
Forum: E2
Topic: Which stepper motors are installed?
Replies: 4
Views: 73

Which stepper motors are installed?

Which stepper motors are installed?
Where can I find data sheets
by Proschi3d
Tue Jan 12, 2021 10:13 am
Forum: E2
Topic: E2 Paused printing
Replies: 16
Views: 317

Re: E2 Paused printing

more and more people have this problem. Maybe someone cares about a solution here? I think a lot of them have this problem and don't notice.
by Proschi3d
Sat Jan 09, 2021 7:39 pm
Forum: E2
Topic: Ribbon pin out
Replies: 10
Views: 325

Re: Ribbon pin out

I was in contact with escher 3d, it was confirmed that Raise3d has to adhere to the license agreement and has to publish the pin-out and all documentation
by Proschi3d
Fri Jan 08, 2021 7:16 pm
Forum: E2
Topic: Printer pauses and grooves in the Z axis.
Replies: 27
Views: 735

Re: Printer pauses and grooves in the Z axis.

Right. They have enough problems with their presidents
by Proschi3d
Fri Jan 08, 2021 2:13 pm
Forum: E2
Topic: Printer pauses and grooves in the Z axis.
Replies: 27
Views: 735

Re: Printer pauses and grooves in the Z axis.

the problem probably only exists in the EU.
It's down to the stuttering electricity provider. :)
by Proschi3d
Tue Jan 05, 2021 10:24 pm
Forum: E2
Topic: Ribbon pin out
Replies: 10
Views: 325

Re: Ribbon pin out

I think that cheaper China scrap is sold at a high price. The device goes back to the manufacturer.
by Proschi3d
Tue Jan 05, 2021 10:34 am
Forum: E2
Topic: Ribbon pin out
Replies: 10
Views: 325

Re: Ribbon pin out

Imitation is the sincerest form of flattery. The PCB masking says it's a reproduction based on the duet board and is not endorsed or supported by the originators - not a licensed product. In other words, it's a clone. Any modifications Raise3D has done to it may be considered IP and the company is ...
by Proschi3d
Sat Jan 02, 2021 11:36 am
Forum: E2
Topic: Ribbon pin out
Replies: 10
Views: 325

Re: Ribbon pin out

I don't think it's good that my request is not responded to. You are obliged to publish the pinout. It is part of the duet wifi license agreement

I hereby draw your attention to it again. If nobody cares about it, I will arrange it in another way
by Proschi3d
Wed Dec 30, 2020 6:27 pm
Forum: E2
Topic: Ribbon pin out
Replies: 10
Views: 325

Re: Ribbon pin out

I would be happy to show you the back of your motion board. You can probably tell that you are obliged to publish the pinnaout!
by Proschi3d
Tue Dec 29, 2020 5:26 pm
Forum: E2
Topic: Printer pauses and grooves in the Z axis.
Replies: 27
Views: 735

Re: Printer pauses and grooves in the Z axis.

The pause occurs from the local memory as well as via USB, only when I unplug the control board and send it directly from my PC via USB it prints without a pause
by Proschi3d
Tue Dec 29, 2020 8:02 am
Forum: E2
Topic: Ribbon pin out
Replies: 10
Views: 325

Re: Ribbon pin out

It is part of the operation license. Therefore I would like to have a complete pinout of the motion board
by Proschi3d
Sun Dec 27, 2020 3:41 pm
Forum: E2
Topic: Get proper harden/steel nozzle for the E2
Replies: 28
Views: 1423

Re: Get proper harden/steel nozzle for the E2

PID for a 50W
by Proschi3d
Sat Dec 26, 2020 8:27 am
Forum: Software
Topic: Gcode syntax for E2
Replies: 20
Views: 423

Re: Gcode syntax for E2

Thank you for sharing. I found a little bug. After the prime line, the printer moves into the extruded material. Maybe we should open an extra thread? We can open a new thread, or continue the discussion on Github. But this line after the prime line should make it go to Z5 to not go into the extrud...
by Proschi3d
Thu Dec 24, 2020 3:39 pm
Forum: E2
Topic: Ribbon pin out
Replies: 10
Views: 325

Re: Ribbon pin out

Picture
by Proschi3d
Thu Dec 24, 2020 1:18 pm
Forum: E2
Topic: Ribbon pin out
Replies: 10
Views: 325

Ribbon pin out

Can someone tell me how the ribbon cable is occupied? I want to connect an original Duet WiFi.there are the fans and temperature sensors on the ribbon cable Since the motion board is a board based on the Duet WiFi, I would like a detailed pin assignment, also via PM 3.3. The Licensee may modify the ...

Go to advanced search