Search found 11 matches

by Timo
Fri Aug 14, 2020 8:01 pm
Forum: E2
Topic: filament wont unload or load
Replies: 6
Views: 257

Re: filament wont unload or load

The dealer said that wire breakage during filament change is common in 3D printers, and removing the jam does not void the warranty. I was able to remove the jam easily, after disassembling the print head. Anyone who disassembles the printhead in RAISE 3D E2 Note that the larger gear has 2 bearings ...
by Timo
Sat Aug 08, 2020 11:53 am
Forum: E2
Topic: filament wont unload or load
Replies: 6
Views: 257

Re: filament wont unload or load

To biketracer. Ofc i did like printer says.
by Timo
Sat Aug 08, 2020 9:02 am
Forum: E2
Topic: filament wont unload or load
Replies: 6
Views: 257

Re: filament wont unload or load

How i do that. Make a ticket even i am not in US?.
by Timo
Fri Aug 07, 2020 3:39 pm
Forum: E2
Topic: filament wont unload or load
Replies: 6
Views: 257

filament wont unload or load

I tried to change the filament. The filament got stuck and now doesn’t move in one direction or another. If I begin disassembling the printhead by following the instructions on the support page, is the printer still under warranty ?. Now that the filament is still stuck in the printhead, should I cu...
by Timo
Mon Aug 03, 2020 9:04 pm
Forum: E2
Topic: E2 Motion controller firmware says install failed
Replies: 23
Views: 790

Re: E2 Motion controller firmware says install failed

I didn’t read the whole thing, but when you upgrade the E2 printer firmware, be sure to turn off the machine at the back of the switch. Not on screen. I also got an error myself when I tried to restart printer from the screen.
by Timo
Mon Aug 03, 2020 9:00 pm
Forum: E2
Topic: E2 Hepa Filter Fan
Replies: 59
Views: 1672

Re: E2 Hepa Filter Fan

My E2 will turn it off after 5 min.
by Timo
Sat Jul 11, 2020 12:03 pm
Forum: E2
Topic: Raise 3D E2 maintenance
Replies: 4
Views: 324

Raise 3D E2 maintenance

So in maintenance page in "how to lube axes" tells "Note: It's recommended to use Super Lube PTFE or a similar type of lube.". So its grease or oil?.
by Timo
Sat Jul 11, 2020 10:32 am
Forum: E2
Topic: Raise 3D E2 hotend v2
Replies: 1
Views: 189

Raise 3D E2 hotend v2

Can we use v2 hotend extruder Setup in ideamaker whit raide D3 e2?. There is no presetup template to hotend v2.
by Timo
Mon Jul 06, 2020 8:05 am
Forum: E2
Topic: Didint go tru first print.
Replies: 1
Views: 116

Didint go tru first print.

I didn’t do the first test print, and afterwards I noticed that it would have involved calibrating the X-Y axes. Can I calibrate the axes afterwards, or Can I do the first print wizard again ?. Does this forum work? my post doesn't appear.
by Timo
Fri Jul 03, 2020 1:32 pm
Forum: E2
Topic: Raise 3D E2 Main power and X-level.
Replies: 1
Views: 138

Raise 3D E2 Main power and X-level.

Hey. I just bought a Raise E2 3D Printer, and I've been happy with the quality of the printer. A few questions about the machine. 1. The printer does not have a power button, only the main power button on the back. I think when I turn off the machine from there, the X-axis plane doesn’t stay straigh...
by Timo
Thu Jul 02, 2020 10:08 pm
Forum: E2
Topic: compatible filaments for E3
Replies: 7
Views: 464

Re: compatible filaments for E3

They are working on a list of compatible fillaments on E2. Atleast i saw some post about it.

Go to advanced search