Search found 65 matches

by Raise3D_User1
Mon Jun 14, 2021 9:48 pm
Forum: E2
Topic: Copperhead with E3D Replacement 24v/40w heater heating time test
Replies: 3
Views: 114

Re: Copperhead with E3D Replacement 24v/40w heater heating time test

Interesting, thanks for sharing. ... I was on the way to apply also 30W when I have seen your post, thanks for it. FYI, these were the ones I bought: https://quantum3dprinting.com/shop/genuine-e3d-heater-cartridge-24v-40w-e-heater-24v-40w/ They actually arrived white instead of red, but the part nu...
by Raise3D_User1
Sun Jun 13, 2021 11:29 pm
Forum: E2
Topic: Copperhead with E3D Replacement 24v/40w heater heating time test
Replies: 3
Views: 114

Copperhead with E3D Replacement 24v/40w heater heating time test

Just posting this for people interested in switching to a Copperhead setup. I have multiple E2 units and have never really been satisfied with the hotend, so I've been switching them over one at a time to Copperheads with E3D heaters and the time from start until they're heated up and ready to go is...
by Raise3D_User1
Sun Jun 13, 2021 5:54 am
Forum: E2
Topic: Changing Out Your Buildtak
Replies: 4
Views: 163

Re: Changing Out Your Buildtak

Has anyone changed out the original Buildtak surface on your E2? I purchased the Buildtak here: ...and still have the plastic red tab (that goes at the front of the print bed), which I can bring over to the new Buildtak sheet. I think Im just curious how one actually removes the original printing s...
by Raise3D_User1
Tue Jun 08, 2021 7:51 am
Forum: E2
Topic: Bed Engraving
Replies: 4
Views: 142

Re: Bed Engraving

Your nozzle is too low or your hotend isn't all the way pushed in, so the whole thing is lower than it was. You can adjust for this and use the .3mm card to check the nozzle. Go to the gear icon in the upper right, then more settings -> hardware -> z offset and set both the nozzles to an offset that...
by Raise3D_User1
Thu Jun 03, 2021 3:19 am
Forum: Software
Topic: Prepare to Slice window not resizable
Replies: 5
Views: 293

Re: Prepare to Slice window not resizable

Vicky@Raise3D wrote:You can drag the right bottom conrer of the panel to adjust the size.


It would be nice if the software remembered your setting from the last time you used it instead of defaulting to too small every time you start it.
by Raise3D_User1
Wed Jun 02, 2021 10:33 pm
Forum: E2
Topic: Copperhead Heater Cartridge
Replies: 12
Views: 1739

Re: Copperhead Heater Cartridge

Been running the copperheads with .4 vanadium hardened nozzles on one of the E2s for the last 5 days and it's a night and day difference compared to the terrible stock heatbreak/hot block. I ordered 4 more sets yesterday so I can upgrade my other two E2s. Highly recommended to do this if you have an...
by Raise3D_User1
Wed Jun 02, 2021 10:17 pm
Forum: Software
Topic: My printer connects, but refuses to accept uploads
Replies: 31
Views: 7639

Re: My printer connects, but refuses to accept uploads

Vicky@Raise3D wrote:We have figured out the problem and can generate a beta version for you if you'd like to help us test.


They sent me a link with the version that disallows special characters. I'll install it tonight.
by Raise3D_User1
Sat May 29, 2021 8:10 pm
Forum: E2
Topic: Copperhead Heater Cartridge
Replies: 12
Views: 1739

Re: Copperhead Heater Cartridge

For the record, here's the parts to put the correct connector on the naked heater block lines you get when you replace the E2 one (that's too small for the Copperhead): Crimp connectors (3 cents, you need 2 per Copperhead): https://www.newark.com/jst-japan-solderless-terminals/sxh-001t-p0-6/contact-...
by Raise3D_User1
Sat May 29, 2021 8:03 pm
Forum: E2
Topic: Help with Copperhead Installation
Replies: 6
Views: 1286

Re: Help with Copperhead Installation

For the record, here's the parts to put the correct connector on the naked heater block lines you get when you replace the E2 one (that's too small for the Copperhead): Crimp connectors (3 cents, you need 2 per Copperhead): https://www.newark.com/jst-japan-solderless-terminals/sxh-001t-p0-6/contact-...
by Raise3D_User1
Sat May 29, 2021 8:01 pm
Forum: E2
Topic: Get proper harden/steel nozzle for the E2
Replies: 44
Views: 4798

Re: Get proper harden/steel nozzle for the E2

For the record, here's the parts to put the correct connector on the naked heater block lines you get when you replace the E2 one (that's too small for the Copperhead): Crimp connectors (3 cents, you need 2 per Copperhead): https://www.newark.com/jst-japan-solderless-terminals/sxh-001t-p0-6/contact-...
by Raise3D_User1
Sat May 29, 2021 7:03 pm
Forum: E2
Topic: Get proper harden/steel nozzle for the E2
Replies: 44
Views: 4798

Re: Get proper harden/steel nozzle for the E2

Somehow I missed the "auto tune" option for PID and was looking at the manual numbers wondering what they should be. Found the auto-tune PID and have that running now...
by Raise3D_User1
Sat May 29, 2021 10:53 am
Forum: E2
Topic: Get proper harden/steel nozzle for the E2
Replies: 44
Views: 4798

Re: Get proper harden/steel nozzle for the E2

The copperhead heat break has a significantly higher thermal mass, so the original spec'd 30w heater would yield a slower heatup time at the same duty cycle. Ive been running the E3D 40W, (24v has white wires) and after a PID autotune, it is snappy. I ordered the slice engineering higher wattage on...
by Raise3D_User1
Sat May 29, 2021 6:59 am
Forum: E2
Topic: Get proper harden/steel nozzle for the E2
Replies: 44
Views: 4798

Re: Get proper harden/steel nozzle for the E2

The copperhead heat break has a significantly higher thermal mass, so the original spec'd 30w heater would yield a slower heatup time at the same duty cycle. Ive been running the E3D 40W, (24v has white wires) and after a PID autotune, it is snappy. I ordered the slice engineering higher wattage on...
by Raise3D_User1
Fri May 28, 2021 3:27 am
Forum: Software
Topic: My printer connects, but refuses to accept uploads
Replies: 31
Views: 7639

Re: My printer connects, but refuses to accept uploads

Problem's back. Can't upload to any of the printers again. HOWEVER, I think I know what happened this time. When uploading a file, I put "255/260/80" at the end of the file name for the model so I would know the temps for that version. Raise uploaded the file as "80" - it truncat...
by Raise3D_User1
Wed May 26, 2021 3:49 am
Forum: Software
Topic: My printer connects, but refuses to accept uploads
Replies: 31
Views: 7639

Re: My printer connects, but refuses to accept uploads

We have generated a beta version ideaMaker which can show more information of the error in uploading queue. Let me know if you have interest in helping us test the issue. Yes, thank you. I came back to post that support sent me a version of the ideamaker that gave them more information about the pr...
by Raise3D_User1
Sat May 15, 2021 7:46 pm
Forum: Software
Topic: poor quality of support structure
Replies: 5
Views: 1476

Re: poor quality of support structure

What does this look like when you preview the slice job after slicing it? Can you screen cap the program window?

Also, screen cap your support tabs for your settings.
by Raise3D_User1
Fri May 14, 2021 6:58 am
Forum: E2
Topic: HELP - Left Printhead Continually Fails
Replies: 2
Views: 897

Re: HELP - Left Printhead Continually Fails

Is your side fan on the left extruder working? Is the vent that guides the output from that fan not warped? I have one that has become warped and I think it makes the cooling weird so that I have a similar issue with the right extruder on one of mine with PETG. I'll have to open a ticket myself...
by Raise3D_User1
Fri May 14, 2021 3:56 am
Forum: Software
Topic: My printer connects, but refuses to accept uploads
Replies: 31
Views: 7639

Re: My printer connects, but refuses to accept uploads

Nope. No joy. The IP address displayed beneath the name of each printer on the remote window is the same as the IP address in the ethernet panel of the E2 machines (I'm not using wireless at all now to eliminate one more potential point of failure). Adding the port to the firewall as trusted made no...
by Raise3D_User1
Thu May 13, 2021 6:56 pm
Forum: Software
Topic: My printer connects, but refuses to accept uploads
Replies: 31
Views: 7639

Re: My printer connects, but refuses to accept uploads

Updated to Ideamaker 4.1.1 and now I have this issue as well. Stuck on "waiting" forever on an E2 (EDIT: It won't upload to ANY of my 3 E2 machines now, so it has to be on the software and not the machine(s)). All of them work with the remote app fine. I rebooted, reloaded ideamaker, chang...
by Raise3D_User1
Sat May 01, 2021 5:31 am
Forum: E2
Topic: E2 maintenance?
Replies: 5
Views: 1193

Re: E2 maintenance?

Steven@Raise3D wrote:
Bikeracer wrote:Last time this came up Super Lube was mentioned.

https://www.amazon.co.uk/gp/product/B01 ... UTF8&psc=1


Yes, we recommend using Super Lube lubricating grease with PTFE.



Thanks. Everything's cleaned and lubed again and running much better again.

Go to advanced search