Search found 375 matches
- Tue Mar 19, 2019 6:56 pm
- Forum: General
- Topic: Bed Leveling
- Replies: 1
- Views: 468
Re: Bed Leveling
Always, do it with right nozzle and bed temp... but only for filament... you should plan to use.
- Tue Mar 19, 2019 6:53 pm
- Forum: General
- Topic: Remove Silicone Covers for High Temps?
- Replies: 2
- Views: 299
Re: Remove Silicone Covers for High Temps?
Beware if you want to clean it... after high temps, is easy to tear it apart...
- Tue Mar 19, 2019 6:51 pm
- Forum: Printing Settings
- Topic: PETG
- Replies: 5
- Views: 470
- Thu Mar 07, 2019 4:28 am
- Forum: Software
- Topic: Alternative Slicing Engines?
- Replies: 11
- Views: 711
Re: Alternative Slicing Engines?
I was try to start wit IM. But no luck. Chaos software. Too much options injected in few windows without logic.
- Fri Feb 22, 2019 5:25 am
- Forum: General
- Topic: More on removing parts with alcohol
- Replies: 7
- Views: 2303
Re: More on removing parts with alcohol
I was try alcohol wit Buildtak. And 50% water mixture with isopropyl works good. But Buildtak sucks. Bubbles.
- Thu Feb 21, 2019 7:08 pm
- Forum: General
- Topic: More on removing parts with alcohol
- Replies: 7
- Views: 2303
Re: More on removing parts with alcohol
I'm using PEI with ABS, Polycarbonate and without any problem. They came off easily. Try do adjust Z-axis a little bit higher... or use Buidtak 90 degrees spatula. This tool looks stupid and weird, bor works perfectly.
- Tue Feb 19, 2019 8:14 am
- Forum: General
- Topic: Disaster: fused PLA around the nozzle and extruder
- Replies: 4
- Views: 388
Re: Disaster: fused PLA around the nozzle and extruder
Use heat gun blower and sharp tools. Slowly.
- Fri Feb 15, 2019 8:28 am
- Forum: Pro2 Series
- Topic: z probe/sensor upgrade
- Replies: 15
- Views: 726
- Thu Feb 14, 2019 7:02 pm
- Forum: Pro2 Series
- Topic: Support material/structures breaking
- Replies: 6
- Views: 329
Re: Support material/structures breaking
Z-hop. You should use this feature and adjust also Z-axis higher. For example 0.25mm. That way.
- Tue Feb 12, 2019 7:25 pm
- Forum: Pro2 Series
- Topic: Is this level of guide rail wear normal? (5 month old Pro2)
- Replies: 15
- Views: 742
Re: Is this level of guide rail wear normal? (5 month old Pro2)
Sliding sleeve to replace...
- Mon Feb 11, 2019 4:14 pm
- Forum: Hardware
- Topic: What on **** caused my N2 Dual the throw a new glass plate out of the closed door after 7 hours printing?
- Replies: 8
- Views: 630
Re: What on **** caused my N2 Dual the throw a new glass plate out of the closed door after 7 hours printing?
Z-axis calibration and Z hoop value. And few more adjustments...
- Mon Feb 11, 2019 9:07 am
- Forum: Pro2 Series
- Topic: Is this level of guide rail wear normal? (5 month old Pro2)
- Replies: 15
- Views: 742
Re: Is this level of guide rail wear normal? (5 month old Pro2)
Not. You should to lubricate it.
- Tue Jan 29, 2019 7:28 pm
- Forum: Printing Settings
- Topic: Flexifill FormFutura settings
- Replies: 0
- Views: 179
Flexifill FormFutura settings
Ok, first you should te remove tubes from the extruder or use oil. Friction totally stops filament is not possible to pull it out from spool with tubes... second warping... I'm using blue tape or Kapton but still, after few layers, it can pell of at corner... Any ideas?
- Sat Jan 26, 2019 10:46 am
- Forum: Pro2 Series
- Topic: Researching UPS for Pro2? What is it's max wattage?
- Replies: 3
- Views: 215
Re: Researching UPS for Pro2? What is it's max wattage?
1000 W will be ok. Plus 100Ah battery. This setup work for me:
http://voltpolska.pl/pl/glowna/70-zasil ... e-12v.html
http://voltpolska.pl/pl/glowna/70-zasil ... e-12v.html
- Fri Jan 25, 2019 1:18 pm
- Forum: Printing Settings
- Topic: Polycarbonate stringing and poor surface finish
- Replies: 12
- Views: 466
- Fri Jan 25, 2019 10:04 am
- Forum: Printing Settings
- Topic: Polycarbonate stringing and poor surface finish
- Replies: 12
- Views: 466
Re: Polycarbonate stringing and poor surface finish
I'm using Polymaker Polycarbonate and print perfectly all time. Try to dry it first.
- Fri Jan 25, 2019 10:03 am
- Forum: Printing Settings
- Topic: Strange surface finish on PLA print
- Replies: 6
- Views: 349
Re: Strange surface finish on PLA print
Too low infill and surface layers amount or water in the filament.
- Wed Jan 23, 2019 8:35 pm
- Forum: User's Gallery
- Topic: Look at this!
- Replies: 5
- Views: 796
Re: Look at this!
I know this feeling very well:
https://www.youtube.com/watch?v=0ITE17EQQbA
Bad support. You should have a big connection area between both materials. Or use PVA only for dense...
https://www.youtube.com/watch?v=0ITE17EQQbA
Bad support. You should have a big connection area between both materials. Or use PVA only for dense...
- Sat Jan 19, 2019 8:53 am
- Forum: Pro2 Series
- Topic: Removing the HEPA filter
- Replies: 2
- Views: 179
- Sat Jan 19, 2019 8:50 am
- Forum: General
- Topic: Is it OK to buy the Pro 2 now?
- Replies: 15
- Views: 1134
Re: Is it OK to buy the Pro 2 now?
The machine is overpriced and well not finished. Maybe for half of the price. After a few months of fight working very well... but it cost me too much money and effort. Printing head assembly is terrible. This is not module construction. If something goes wrong you are in serious troubles without me...