Search found 9 matches

by Lorenzo
Wed Jul 25, 2018 9:23 am
Forum: Software
Topic: Ideamaker 3.1.7 Impossible to print with raft
Replies: 7
Views: 1380

Re: Ideamaker 3.1.7 Impossible to print with raft

I double checked Per-layer and Per-Group settings. Both were empty. I also checked the filament settings for the left extruder, again no over rides were active. I'm only printing with the left extruder but I did check the right extruder filament settings as well, PVA was selected there, eventho I do...
by Lorenzo
Mon Jul 23, 2018 11:11 am
Forum: Software
Topic: Ideamaker 3.1.7 Impossible to print with raft
Replies: 7
Views: 1380

Re: Ideamaker 3.1.7 Impossible to print with raft

Hello Vicky,

The 20 mm Gcode file works perfectly, with raft. I imported the data file as a profile. I sliced a part with that profile and again, no raft.
I added the files from the part I sliced to this message.

Kind regards,

Lorenzo
by Lorenzo
Mon Jul 23, 2018 10:58 am
Forum: Pro2 Series
Topic: Cold nozzles reading 240° C
Replies: 95
Views: 14157

Re: Cold nozzles reading 240° C

This is actually a pretty dangerous/critical failure. As noted by others in this thread, it can occur in the middle of a print. In case the hot end shows a high temperature when it happens, it only cools down and prints in the air. In case it is heating up, it can overheat causing damage to the prin...
by Lorenzo
Mon Jul 16, 2018 11:40 am
Forum: Software
Topic: Ideamaker 3.1.7 Impossible to print with raft
Replies: 7
Views: 1380

Re: Ideamaker 3.1.7 Impossible to print with raft

Hello Vicky, I already sent the data and gcode file for one of my prints to Rachel on the 12th of july. The data and Gcode file both say it should be printed with a brim, but I can assure you that the profile I'm using for slicing says raft and the brim options are even greyed out. When I do a print...
by Lorenzo
Tue Jul 10, 2018 6:03 am
Forum: Pro2 Series
Topic: AVM FRITZ!DECT 200 ?
Replies: 14
Views: 1593

Re: AVM FRITZ!DECT 200 ?

I agree that the on/off switch is in a bad location, but I don't see a better one from the get go. On the sides it may be inadvertently pushed while operating and I believe the on/off switch is part of the stock power supply, much like the one in personal computers.

Kind regards,

Lorenzo
by Lorenzo
Mon Jul 09, 2018 11:44 am
Forum: Software
Topic: Ideamaker 3.1.7 Impossible to print with raft
Replies: 7
Views: 1380

Ideamaker 3.1.7 Impossible to print with raft

Al ready created a support ticket, but wanted to open up the discussion here as well. When I get a fix, i'll post it here too. It seems impossible to create Gcode with a raft in 3.1.7. Instead of a raft, it prints a brim. No matter what I do, it always reverts to brim instead of raft. What did I che...
by Lorenzo
Mon Jul 09, 2018 11:29 am
Forum: Pro2 Series
Topic: Cold nozzles reading 240° C
Replies: 95
Views: 14157

Re: Cold nozzles reading 240° C

Seems reseating the connectors fixed the problem for me as well. :)

Kind regards,

Lorenzo
by Lorenzo
Mon Jul 09, 2018 5:57 am
Forum: Pro2 Series
Topic: Cold nozzles reading 240° C
Replies: 95
Views: 14157

Re: Cold nozzles reading 240° C

Hello,

Going to try and reseat the connectors, thanks for the picture David, will take the picture as well just before reseating and checking.

kind regards,

Lorenzo
by Lorenzo
Fri Jul 06, 2018 6:31 am
Forum: Pro2 Series
Topic: Cold nozzles reading 240° C
Replies: 95
Views: 14157

Cold nozzles reading 240° C

Hello, Just noticed this morning that my Pro2+ printer's nozzle temperatures are shown to be at 246° C in the touchscreen under utilities tab, but when I touch them they are cold. This proves problematic as I need to unload my filament to load in a different color for our production facility, but I ...

Go to advanced search