Search found 38 matches

by Michal80
Tue Aug 11, 2020 8:23 pm
Forum: General
Topic: N1 problem
Replies: 14
Views: 975

Re: N1 problem

The problem seems to be resolved for me. I installed ideamaker again, 5 prints from PLA no problem. I can not explain that. I will test it on a few more prints.
by Michal80
Sun Aug 09, 2020 7:31 pm
Forum: General
Topic: N1 problem
Replies: 14
Views: 975

Re: N1 problem

Default settings printed on each PLA template, 0.4 nozzle. Filament producer Finnotech, Raise, Print me, Devil desing for every problem, this was not the case before. The problem suddenly appeared and continues. Unfortunately.
by Michal80
Sun Aug 09, 2020 3:29 pm
Forum: General
Topic: N1 problem
Replies: 14
Views: 975

Re: N1 problem end PRO 2

I have exactly the same problem on PRO 2. PLA filaments get blocked randomly, only PLA. ABS, PETG print without problems. I replaced all the fans, new nozzles, heating blocks, tubes with no effect. My Raise doesn't print from PLA :(. I'm out of ideas. What could be the reason? https://i.postimg.cc/M...
by Michal80
Mon Jul 27, 2020 6:57 pm
Forum: Others
Topic: LAYER START SETTING PRO 2
Replies: 3
Views: 737

Re: LAYER START SETTING PRO 2

For me, the problem is on the walls from 0.8 mm to 1.2 mm, the thicker seamed walls are printed correctly. I read somewhere that you have to change the g-code. I've never done it too high level
by Michal80
Sun Jul 26, 2020 5:09 pm
Forum: Others
Topic: LAYER START SETTING PRO 2
Replies: 3
Views: 737

LAYER START SETTING PRO 2

Hi everyone. I have a problem with the correct printing (setting) of the seam on a 0.8 mm - 1.2 mm thin wall. The seam comes out very ugly. Changing the settings has no effect. I have no idea what to do. https://i.postimg.cc/9MJmC319/20200726-183036.jpg https://i.postimg.cc/z3mXPC02/Screenshot-20200...
by Michal80
Sun May 17, 2020 7:10 pm
Forum: Printing Settings
Topic: Double color
Replies: 6
Views: 763

Re: Double color

Thank you for your help. Full success :D Image
by Michal80
Wed May 13, 2020 7:01 pm
Forum: Printing Settings
Topic: Double color
Replies: 6
Views: 763

Re: Double color

I have restored the factory settings of the printer, is this the reason for moving the axis? Do you have any base parameter from which I can start to set the right extruder axis? The offset is +/- 30 mm. I am a beginner Raise user, so here are so many questions :)
by Michal80
Tue May 12, 2020 4:25 pm
Forum: Printing Settings
Topic: Double color
Replies: 6
Views: 763

Re: Double color

Thanks for the advice, I will calibrate the x-axis, I'll let you know how it went. I don't understand why these settings have changed, the extruder parameters on the Raise PRO 2 printer are never changed
by Michal80
Sun May 10, 2020 5:04 pm
Forum: Printing Settings
Topic: Double color
Replies: 6
Views: 763

Double color

There was a problem printing two colors at the same time. Left exdruder and right exdruder do not overlap on the prepared model. I don't understand why this is happening. Default settings, no problem before. https://i.postimg.cc/dVd359My/20200510-184229.jpg https://i.postimg.cc/523yc204/20200510-190...
by Michal80
Tue May 05, 2020 7:02 pm
Forum: General
Topic: Overhang printing
Replies: 20
Views: 3910

Re: Overhang printing

I downloaded the G-code file which you sent, the mask with a large sag came out very badly. I compared it, you changed the seam, the rest of the settings are the default. Masks prepared in Cura end Z-SUITE also have default settings, only the filling has been changed. My settings do not make sense r...
by Michal80
Sun May 03, 2020 1:17 pm
Forum: General
Topic: Overhang printing
Replies: 20
Views: 3910

Re: Overhang printing

I printed models with Gcode prepared, for me the overhang effect is very bad, no matter if there are supports or there are not. Internal and external walls are very nice :). Please enter what settings have been changed. How has the seam location changed? Below I am sending photos showing the same mo...
by Michal80
Wed Apr 29, 2020 4:04 pm
Forum: General
Topic: Overhang printing
Replies: 20
Views: 3910

Re: Overhang printing

I have analyzed this problem and I still cannot get a good printout. In my opinion the problem is the starting point. The parameter (fixed start position in the Y axis) of picture-1 is responsible for changing the seam location of the outer wall, it works only when using the parameter print outer wa...
by Michal80
Thu Apr 23, 2020 7:40 pm
Forum: General
Topic: Overhang printing
Replies: 20
Views: 3910

Re: Overhang printing

Vicky I understand I printed this model even on a cold table with the help of glue the effect is bad. My observation shows that the problem is the option to set the seam. On the fixed seam setting comes out worst. I do not understand what settings to choose the best for this model. Can you explain t...
by Michal80
Wed Apr 22, 2020 10:20 am
Forum: General
Topic: Overhang printing
Replies: 20
Views: 3910

Re: Overhang printing

I send two Gcode one better the other very bad. All the time the quality of the printed model is far from ideal. Please advise how to change the seam location. It is still visible on the top of the mask (nose). Thank you for your help
by Michal80
Mon Apr 20, 2020 8:25 pm
Forum: General
Topic: Overhang printing
Replies: 20
Views: 3910

Re: Overhang printing

Hi. Please help. I can't deal with printing the mask on Raise pro2, the model is just ugly. I printed with and without supports, the effect is still bad. The uploaded photos show two prints from two printers. The black model printed on ANYCUBIC & CURA is a good, white model printed on Raise pro2...
by Michal80
Fri Apr 10, 2020 8:27 pm
Forum: General
Topic: Overhang printing
Replies: 20
Views: 3910

Re: Overhang printing

I prints without the top cover with open covers, the fans work correctly 100% setting. The effect is not satisfactory. I have a second Anycubic i3 Mega printer, CURA without support, the mask model comes out very nice, Raise very bad. Is the problem only in cooling or does any parameter affect it?
by Michal80
Thu Apr 09, 2020 4:45 pm
Forum: General
Topic: Overhang printing
Replies: 20
Views: 3910

Overhang printing

Hi, I want to print a protective mask to help hospitals. Despite many attempts, the quality is far from expectations. I am asking for help in correcting the settings parameters. I print on the default PLA template standard, filament Raise. https://i.postimg.cc/fyX06LqQ/1.jpg https://i.postimg.cc/B6P...
by Michal80
Wed Apr 08, 2020 7:29 pm
Forum: General
Topic: Raise3D PRO 2 Print quality
Replies: 25
Views: 7544

Re: Raise3D PRO 2 Print quality

Hi, I want to print a protective mask to help hospitals. Despite many attempts, the quality is far from expectations. I am asking for help in correcting the settings parameters. I print on the default PLA template standard, filament Raise. https://i.postimg.cc/fyX06LqQ/1.jpg https://i.postimg.cc/B6P...
by Michal80
Fri Mar 20, 2020 8:51 pm
Forum: General
Topic: ABS PROBLEM
Replies: 11
Views: 3073

Re: ABS PROBLEM

I will follow my advice and let you know. Please cut this model for me, the walls are thicker. I will do a test.
by Michal80
Wed Mar 18, 2020 6:32 pm
Forum: General
Topic: ABS PROBLEM
Replies: 11
Views: 3073

Re: ABS PROBLEM

I use ABS - MONSTICK, Devil Design

Go to advanced search