Search found 8057 matches

by Vicky@Raise3D
Wed Jul 28, 2021 4:58 am
Forum: Software
Topic: Embedded textures
Replies: 4
Views: 301

Re: Embedded textures

It only takes .obj files at the moment.
Attached the instruction blog for your reference: https://www.ideamaker.io/blogDetail.html?id=64
by Vicky@Raise3D
Wed Jul 28, 2021 4:57 am
Forum: Software
Topic: Shell thickness change when sliced
Replies: 7
Views: 139

Re: Shell thickness change when sliced

The thickness of the model is not the sam. When the thicker section is more than 2 times of the thickness of Thin Wall, it will be shells. Because the nozzle can't physically extruder that wide line to match the width.
by Vicky@Raise3D
Tue Jul 27, 2021 1:15 am
Forum: Software
Topic: Single Layer, Solid Infill flow rate adjustment
Replies: 3
Views: 116

Re: Single Layer, Solid Infill flow rate adjustment

When it's only one layer, the layer will be considered as Top Surface Layer.
You can disable the Top Surface Layer to be 0 and try again.

We will see how to improve the calculation for similar case in future versions.
by Vicky@Raise3D
Tue Jul 27, 2021 1:13 am
Forum: Software
Topic: Shell thickness change when sliced
Replies: 7
Views: 139

Re: Shell thickness change when sliced

The sections marked in your image before, the thickness of the model is different from other sections. With ThinWall disabled, you can find shell loops are closer to each other, some of them are overlapped.
by Vicky@Raise3D
Sat Jul 24, 2021 2:46 am
Forum: Software
Topic: Single Layer, Solid Infill flow rate adjustment
Replies: 3
Views: 116

Re: Single Layer, Solid Infill flow rate adjustment

Have tried to mark all types solid fill in the picture below.
Image_20210723194548.png
by Vicky@Raise3D
Sat Jul 24, 2021 2:45 am
Forum: Software
Topic: Tree Supports in IdeaMaker
Replies: 8
Views: 4884

Re: Tree Supports in IdeaMaker

Hi derek,
We hear you. We are trying to make it happen!
by Vicky@Raise3D
Fri Jul 23, 2021 4:35 am
Forum: Software
Topic: Shell thickness change when sliced
Replies: 7
Views: 139

Re: Shell thickness change when sliced

From the inner structure of the model, the part below will need shell loop to build the structure. The narrow section needs two loops.
by Vicky@Raise3D
Thu Jul 22, 2021 8:00 pm
Forum: Software
Topic: Fast Travel Moves Cause Layer Shifts
Replies: 10
Views: 338

Re: Fast Travel Moves Cause Layer Shifts

Besides what we have mentioned before, the other differences are speed of bridging and flowrate. Small Feature speed and defect can be different too. If you can share us some pictures of the layer shift on model, we can check whether there's any setting affecting the printing result at the certain s...
by Vicky@Raise3D
Thu Jul 22, 2021 7:52 pm
Forum: Feature Requests, Ideas, Wishes
Topic: IdeaMaker feature requests
Replies: 175
Views: 45734

Re: IdeaMaker feature requests

You can find more information about different filaments under https://www.ideamaker.io/materials-guide.html
There are also available printing templates for different filaments on www.ideamaker.io which a be a good reference to start adjusting when you have a new filament on hand.
by Vicky@Raise3D
Thu Jul 22, 2021 2:00 am
Forum: Software
Topic: Shell thickness change when sliced
Replies: 7
Views: 139

Re: Shell thickness change when sliced

Would you like to share your .idea, .gcode and .data files with us?
by Vicky@Raise3D
Wed Jul 21, 2021 2:24 am
Forum: Software
Topic: Stringing between the support pillars
Replies: 1
Views: 95

Re: Stringing between the support pillars

You will need to select Rectilinear as Support fill.
It will depend of the filament type. If it is not causing a lot extra stringing, you can enable Avoid Unnecessary Retraction in Support.
by Vicky@Raise3D
Wed Jul 21, 2021 2:21 am
Forum: Feature Requests, Ideas, Wishes
Topic: IdeaMaker feature requests
Replies: 175
Views: 45734

Re: IdeaMaker feature requests

We will add some options in ideaMaker to limit the amount of retractions. Besides that, there are already some options in ideaMaker to decrease retraction. You can modify some of them as long as the print result Avoid Retraction Inside Model https://support.raise3d.com/ideaMaker/5-1-3-11-ooze-15-444...
by Vicky@Raise3D
Wed Jul 21, 2021 2:15 am
Forum: Software
Topic: FEATURE IM 4.1.1 Allow User to Set Name for Exported Template
Replies: 2
Views: 84

Re: FEATURE IM 4.1.1 Allow User to Set Name for Exported Template

The template name will be the same as the original one in ideaMaker. Adding the Export is just for separate it from the template already in ideaMaker. You will have access to modify the template name when importing.
by Vicky@Raise3D
Wed Jul 21, 2021 2:04 am
Forum: Software
Topic: Idea Maker - Phone Connection Idea
Replies: 2
Views: 71

Re: Idea Maker - Phone Connection Idea

You can use RaiseCloud App. to monitor printing with your phone which includes remote control and monitor feature. You can find the steps of how to bind your printer with RaiseCloud from the following link: https://cloud.raise3d.com/html/howtobind.html You can download RaiseCloud here: https://cloud...
by Vicky@Raise3D
Tue Jul 20, 2021 12:59 am
Forum: Software
Topic: Z-Seam Question
Replies: 1
Views: 60

Re: Z-Seam Question

We sliced a cube with your settings, the Seams are at the same location.
Image_20210719175819.png

Would you like to share your .idea, .gcode and .data files with us to test?
by Vicky@Raise3D
Tue Jul 20, 2021 12:58 am
Forum: Software
Topic: Retract-Settings
Replies: 1
Views: 41

Re: Retract-Settings

You can try Force Retraction On Layer Change,Force Retraction Before Traveling to Outer Shell.
https://support.raise3d.com/ideaMaker/5 ... 5-444.html
by Vicky@Raise3D
Mon Jul 19, 2021 7:23 pm
Forum: Software
Topic: Coasting setting ignored?
Replies: 2
Views: 84

Re: Coasting setting ignored?

It is pretty obvious to see coasting applied in Preview if you incrase the value to be higher.
Image_20210719121504.png


BTW, which PLA Default template you are slicing with? Normally overhang shells is disabled in default template.
by Vicky@Raise3D
Mon Jul 19, 2021 7:14 pm
Forum: Software
Topic: Brim Extruder Selection
Replies: 12
Views: 637

Re: Brim Extruder Selection

We have found the Virtual Extruder Offset for X has been modified. The default value is 35mm.
Image_20210719120856.png
by Vicky@Raise3D
Sat Jul 17, 2021 12:23 am
Forum: Software
Topic: Slicer questions
Replies: 1
Views: 83

Re: Slicer questions

If you change any settings in default profile, you can restore it back to default settings with the restore button.
You can increase the X and E value for Slim Line.
by Vicky@Raise3D
Fri Jul 16, 2021 3:56 am
Forum: Software
Topic: First layer failed
Replies: 7
Views: 287

Re: First layer failed

It seems the Top surface and Bottom surface settings are different. Once it enabled, it will generate two different types of solid infill.

Go to advanced search