Search found 20 matches

by scienzk
Fri May 12, 2017 11:39 am
Forum: Hardware
Topic: Extruder stops while moving
Replies: 10
Views: 2641

Re: Extruder stops while moving

Vicky@Raise3D wrote:If gently hand move the extruder from origin point to center, is that any stuck or not?


little stuck.
Hard to start to move it while end point
by scienzk
Fri May 12, 2017 5:23 am
Forum: Hardware
Topic: Extruder stops while moving
Replies: 10
Views: 2641

Extruder stops while moving

This is my Raise3D N2 +.
There is a problem with the extruder.
I do not know why it stops while moving.
https://www.youtube.com/embed/gEUMa4tra5U

It well greased on rod.
How can I fix this problem??
by scienzk
Mon Feb 13, 2017 10:16 am
Forum: Hardware
Topic: My N2+ is in Big Trouble. motor and heatbed is not working.
Replies: 15
Views: 1968

Re: My N2+ is in Big Trouble. motor and heatbed is not working.

Yes. I did install myself.
I think it's not wrong.
IMG_1923.JPG

IMG_1924.JPG

IMG_1925.JPG


And my nozzle's are fine. It can raise the temperature. And It can stop raising the temperature.
by scienzk
Mon Feb 13, 2017 3:25 am
Forum: Hardware
Topic: My N2+ is in Big Trouble. motor and heatbed is not working.
Replies: 15
Views: 1968

My N2+ is in Big Trouble. motor and heatbed is not working.

Hi. My N2+ is in big trouble. One day I was doing a normal print. I briefly touched the bed during printing, and the printout was interrupted if there was a problem. After that, I started to get an error message, IMG_1673.JPG IMG_1674.JPG I live in South Korea. So I contacted a Korean agency and got...
by scienzk
Thu Aug 25, 2016 6:51 am
Forum: Hardware
Topic: Dual Printing problems
Replies: 7
Views: 1674

Dual Printing problems

I want to print this. 캡처.PNG But my output is not aligned. IMG_0438.JPG I tried to change extruders offset X 24mm, But it was not the right way. IMG_0439.JPG I tried to reassemble my extruders already. But it was not effective. This phenomenon has occurred and then replace it with a nozzle V2. I hav...
by scienzk
Wed Jul 20, 2016 2:42 am
Forum: Hardware
Topic: Extruder switched off
Replies: 1
Views: 726

Extruder switched off

My printer has been big trouble.
ex.PNG

This error has occur.
I think the problem seems to be caused by a temperature sensor. And My heat rod has broken.
Should I replace all the parts? Before replacing parts Do not operate properly?
by scienzk
Tue Jul 19, 2016 10:10 am
Forum: Hardware
Topic: My hot end's status is getting worse. What can I do??
Replies: 3
Views: 1229

My hot end's status is getting worse. What can I do??

It leaking filament..
IMG_0129.JPG
by scienzk
Tue Jul 19, 2016 5:37 am
Forum: Hardware
Topic: Can I buy this part?
Replies: 5
Views: 1896

Re: Can I buy this part?

I'll get in china.
by scienzk
Tue Jul 19, 2016 4:45 am
Forum: Hardware
Topic: Printing quality problem..
Replies: 11
Views: 2270

Re: Printing quality problem..

Vicky@Raise3D wrote:0.7 or 0.07?

Did you print calibration box when turn to this filament? It seems like over-extrusion.

We will print one of the parts in our office. Will feedback the result when finish. Downloading now.


It is 0.07. sorry.
I print many stuff with this filament.
It is fine before.
by scienzk
Tue Jul 19, 2016 4:43 am
Forum: Hardware
Topic: Can I buy this part?
Replies: 5
Views: 1896

Can I buy this part?

IMG_0128.JPG

I think this part is bend. I want this part only. not whole hot end.
Can I?
by scienzk
Mon Jul 18, 2016 6:13 am
Forum: Hardware
Topic: Printing quality problem..
Replies: 11
Views: 2270

Re: Printing quality problem..

What filament? Which brand? What temperature? Maybe a flowrate problem. Need to know the diameter. Your prints look very small. How much is your layer thickness? Small model needs more cooling, try increase the minimal layer printing time or decrease the printing speed. Or if you don't mind, would ...
by scienzk
Thu Jul 14, 2016 8:46 pm
Forum: Hardware
Topic: Printing quality problem..
Replies: 11
Views: 2270

Re: Printing quality problem..

Also change the grease of those bearings; I don't know why but out of the box the printer's grease is dirty, replace it and it will run much better and smoother. It looks dirty. I know. But it is clean grease. of course PTFE grease. My printer head is move smooth. But before greasing, already worn ...
by scienzk
Thu Jul 14, 2016 8:36 pm
Forum: Hardware
Topic: Printing quality problem..
Replies: 11
Views: 2270

Re: Printing quality problem..

walshlg wrote:May I suggest insulating the hot block.


What is the effect of insulating the hot block?
by scienzk
Thu Jul 14, 2016 11:32 am
Forum: Hardware
Topic: Printing quality problem..
Replies: 11
Views: 2270

Printing quality problem..

My N2+ is getting the output quality is deteriorating. IMG_0071.JPG I sprayed surfacer paint to my printing result. IMG_0073.JPG It was created as look more noticeable the surface. IMG_0076.JPG you can see the lines. IMG_0077.JPG How can I improve the printing quality? My extruder's head strikes pri...
by scienzk
Mon Jul 11, 2016 8:20 am
Forum: Hardware
Topic: How can I add a new fan?
Replies: 5
Views: 1341

How can I add a new fan?

I want to add more fans. I have 40mm fan. It has a molex connector.
N2+ printer head has a 2 more molex connector, but it is not working.
How can I add a new fan?
by scienzk
Thu Mar 24, 2016 4:39 pm
Forum: Software
Topic: Can you make it possible to print different layer thickness?
Replies: 21
Views: 5928

Re: Can you make it possible to print different layer thickness?

I mean different layer thickness in one object.
by scienzk
Wed Mar 23, 2016 12:09 pm
Forum: Hardware
Topic: How can I reset my build area?
Replies: 5
Views: 1707

Re: How can I reset my build area?

It's designed not to be in the center. As the hotend is not in the middle of the extruder carriage. If you indeed want that ,you can just move the bed towards left a little bit. What?? I can't believe that! I just wanted to try just testing the maximum size. The problem occurs stuck in bed retentio...
by scienzk
Wed Mar 23, 2016 4:38 am
Forum: Software
Topic: Can you make it possible to print different layer thickness?
Replies: 21
Views: 5928

Can you make it possible to print different layer thickness?

Hi. I think N2+ is Amaging 3D printer. It can print 0.01mm also. But it takes too long time. So I tried to think. I think if IM can print thickness of the various layers at once would be enormously time reduction. For example, What if the layer thickness of the supporter is print to 0.3mm, and the l...
by scienzk
Wed Mar 23, 2016 3:52 am
Forum: Hardware
Topic: How can I reset my build area?
Replies: 5
Views: 1707

Re: How can I reset my build area?

It's designed not to be in the center. As the hotend is not in the middle of the extruder carriage. If you indeed want that ,you can just move the bed towards left a little bit. What?? I can't believe that! I just wanted to try just testing the maximum size. The problem occurs stuck in bed retentio...
by scienzk
Wed Mar 23, 2016 3:31 am
Forum: Hardware
Topic: How can I reset my build area?
Replies: 5
Views: 1707

How can I reset my build area?

My N2+'s build area is not in center.
mod_DSC04591.jpg
mod_DSC04590.jpg
mod_DSC04588.jpg
mod_DSC04589.jpg

How can I set my build area to center?

Go to advanced search