V2 Hot End Information and Q&A

Topics around mechanical design, controller and electronics. Mods & hacks welcome.
Post Reply
User avatar
John@Raise3D
Posts: 483
Joined: Fri Feb 26, 2016 8:42 am

V2 Hot End Information and Q&A

Postby John@Raise3D » Tue Mar 29, 2016 10:45 am

UPDATE: V2 COMES STANDARD ON ALL NEW PRINTERS AFTER EARLY 2016


V2 Hot End Information

Key features of V2 hot end

1. Wilder filament compatible range
The best feature of V2 hot end is much wilder filament compatible range. We have tested various materials from various suppliers and they all printed very well.

2. Less back pressure when extruding
This makes extruding material easier. Hence the motor is less likely skipping, the filament is less likely to grind and it is less likely to cause air-print.

3. Better print quality
With V2 hot end, model has better surface quality.

Everything is on schedule and we have been taking pre-orders for while already.

Q&A
1. Does V2 hot end come as assembled?
Yes, it is.

2. Does V2 hot end need different heating rod and thermal couple?
No, it does not. You can use the same heating rod and thermal couple for V1 on V2 hot end.

3. Does V2 hot end have the same nozzle as V1?
No, it does not. V1 and V2 hot end nozzles are different from each other.

4. What kind of nozzle does V2 hot end come with?
0.4mm brass nozzle for now and we are developing nozzles with bigger diameter and different material.

5. How can I get V2 hot end?
Please send your request to sales@raise3d.com and we will help you from there. Anyone with V1 hot end will get 30% off on V2 hot end and KS backers get additional 10% off so total 37% off. (V2 hot end MSRP is $79.99 each.)

6. Do I have to switch to V2 hot end?
No, you don't. V1 hot end is also compatible with many different materials. All R3D filaments and PolyMaker filaments on our online store now are guaranteed to compatible with V1 hot end.

7. Is V2 hot end different size with V1 hot end?
V2 hot end and V1 hot end is very close on size. V2 hot end is about 2mm taller than V1 hot end.

A few examples of V2 hot end prints.
Teal.JPG
Teal.JPG (53.21 KiB) Viewed 10016 times
purple.JPG
purple.JPG (57.93 KiB) Viewed 10016 times
pink.JPG
pink.JPG (47.73 KiB) Viewed 10016 times
IMG_0426.JPG
IMG_0426.JPG (37.87 KiB) Viewed 10016 times
IMG_0425.JPG
IMG_0425.JPG (39.68 KiB) Viewed 10016 times
IMG_0424.JPG
IMG_0423.JPG
green.JPG
green.JPG (60.74 KiB) Viewed 10016 times
16 color selection.png
16 color selection.png (182.94 KiB) Viewed 10016 times

80hr ABS.jpg
Z-ABS.jpg
firesped
Posts: 854
Joined: Mon Mar 21, 2016 9:23 pm
Location: Tucson, AZ

Re: V2 Hot End Information and Q&A

Postby firesped » Tue Mar 29, 2016 11:28 am

another question I thought of,

will the stock fan from the V1 work with the V2 that is 2 mm taller now?
RL name: Michael Nolen
printers:
raise3D N2 kickstarter Early Bird
Trinus Deluxe (running smoothieware on Azteeg X5 GT board)
Monoprice Maker Select v2
Jetguy
Posts: 2700
Joined: Tue Mar 22, 2016 1:40 am
Location: In a van, down by the river

Deleted

Postby Jetguy » Tue Mar 29, 2016 1:14 pm

Deleted
Last edited by Jetguy on Thu Apr 07, 2016 4:46 pm, edited 1 time in total.
Jetguy
Posts: 2700
Joined: Tue Mar 22, 2016 1:40 am
Location: In a van, down by the river

Deleted

Postby Jetguy » Tue Mar 29, 2016 1:15 pm

Deleted
Last edited by Jetguy on Thu Apr 07, 2016 4:47 pm, edited 1 time in total.
Jetguy
Posts: 2700
Joined: Tue Mar 22, 2016 1:40 am
Location: In a van, down by the river

Deleted

Postby Jetguy » Tue Mar 29, 2016 2:45 pm

Deleted
Last edited by Jetguy on Thu Apr 07, 2016 4:48 pm, edited 2 times in total.
Jetguy
Posts: 2700
Joined: Tue Mar 22, 2016 1:40 am
Location: In a van, down by the river

Deleted

Postby Jetguy » Tue Mar 29, 2016 3:26 pm

Deleted
Last edited by Jetguy on Thu Apr 07, 2016 4:49 pm, edited 1 time in total.
User avatar
John@Raise3D
Posts: 483
Joined: Fri Feb 26, 2016 8:42 am

Re: V2 Hot End Information and Q&A

Postby John@Raise3D » Tue Mar 29, 2016 3:42 pm

firesped wrote:another question I thought of,

will the stock fan from the V1 work with the V2 that is 2 mm taller now?


It still works for V2.
User avatar
Duplicat
Posts: 11
Joined: Tue Mar 22, 2016 4:16 am

Re: V2 Hot End Information and Q&A

Postby Duplicat » Wed Mar 30, 2016 1:52 am

deleted
Last edited by Duplicat on Fri Apr 08, 2016 6:42 am, edited 1 time in total.
User avatar
John@Raise3D
Posts: 483
Joined: Fri Feb 26, 2016 8:42 am

Re: V2 Hot End Information and Q&A

Postby John@Raise3D » Wed Mar 30, 2016 5:51 am

Not recommended to do such modification, especially change nozzle diameter as it requires change in slicing software also.
Jetguy
Posts: 2700
Joined: Tue Mar 22, 2016 1:40 am
Location: In a van, down by the river

Deleted

Postby Jetguy » Thu Mar 31, 2016 7:01 pm

Deleted
Last edited by Jetguy on Thu Apr 07, 2016 4:49 pm, edited 1 time in total.
User avatar
JolietDelta
Posts: 4
Joined: Tue Mar 29, 2016 5:30 pm

Re: V2 Hot End Information and Q&A

Postby JolietDelta » Wed Apr 06, 2016 7:23 pm

Jacob of 3DPrima (Sweden) just now told me that they won't distribute V2 Nozzles or the replacement leveling screws.
This means that EU users ahve to purchase directly at R3D and get the V2 from the PRC? Is this correct?

Unfortunately I get a SMTP-Error when sending an E-Mail to sales@... So I have to ask this in your FAQ section.
----------------------
Jens
N2+ | S3d
User avatar
John@Raise3D
Posts: 483
Joined: Fri Feb 26, 2016 8:42 am

Re: V2 Hot End Information and Q&A

Postby John@Raise3D » Thu Apr 07, 2016 2:38 am

JolietDelta wrote:Jacob of 3DPrima (Sweden) just now told me that they won't distribute V2 Nozzles or the replacement leveling screws.
This means that EU users ahve to purchase directly at R3D and get the V2 from the PRC? Is this correct?

Unfortunately I get a SMTP-Error when sending an E-Mail to sales@... So I have to ask this in your FAQ section.


We will send it out directly from China through DHL.
If you have problems sending emails to sales@raise3d.com, you can try support@raise3d.com.
fponticelli
Posts: 35
Joined: Thu Mar 24, 2016 3:09 am

Re: V2 Hot End Information and Q&A

Postby fponticelli » Wed Apr 13, 2016 4:29 pm

Any news one when the new hotend will be delivered? Thanks!
User avatar
Vicky@Raise3D
Posts: 4564
Joined: Fri Mar 25, 2016 3:54 am

Re: V2 Hot End Information and Q&A

Postby Vicky@Raise3D » Fri Apr 15, 2016 7:07 am

fponticelli wrote:Any news one when the new hotend will be delivered? Thanks!


We have sent out a batch of V2 hotends from our factory this week by air. Our US warehouse is going to receive them in next two weeks. The hotends will be sent out to customers once in stock.
firesped
Posts: 854
Joined: Mon Mar 21, 2016 9:23 pm
Location: Tucson, AZ

Re: V2 Hot End Information and Q&A

Postby firesped » Fri Apr 15, 2016 9:28 am

I'm hoping that "weeks" equals "days" since air mail is involved. or do you expect a long term at customs?
RL name: Michael Nolen
printers:
raise3D N2 kickstarter Early Bird
Trinus Deluxe (running smoothieware on Azteeg X5 GT board)
Monoprice Maker Select v2
GoffyOne
Posts: 38
Joined: Sat Apr 02, 2016 11:21 am
Location: Sweden

Re: V2 Hot End Information and Q&A

Postby GoffyOne » Fri Apr 15, 2016 10:55 am

Since I am from sweden I guess it is directly sent to me, will I get a tracking nr. when it is sent?
User avatar
John@Raise3D
Posts: 483
Joined: Fri Feb 26, 2016 8:42 am

Re: V2 Hot End Information and Q&A

Postby John@Raise3D » Sat Apr 16, 2016 3:13 am

firesped wrote:I'm hoping that "weeks" equals "days" since air mail is involved. or do you expect a long term at customs?


Hopefully not. We will send out shipping notification when they are out.
User avatar
John@Raise3D
Posts: 483
Joined: Fri Feb 26, 2016 8:42 am

Re: V2 Hot End Information and Q&A

Postby John@Raise3D » Sat Apr 16, 2016 3:17 am

GoffyOne wrote:Since I am from sweden I guess it is directly sent to me, will I get a tracking nr. when it is sent?


Yous will be sent out via air next Monday. We will email you the tracking number.
User avatar
Vicky@Raise3D
Posts: 4564
Joined: Fri Mar 25, 2016 3:54 am

Re: V2 Hot End Information and Q&A

Postby Vicky@Raise3D » Sat Apr 16, 2016 3:21 am

firesped wrote:I'm hoping that "weeks" equals "days" since air mail is involved. or do you expect a long term at customs?


Hi Michael,

Just confirmed. This batch of hotend will be arrived US at the next Monday. Then our US office will send them out individually.
Andy Cohen
Posts: 170
Joined: Mon Mar 21, 2016 4:43 pm

Re: V2 Hot End Information and Q&A

Postby Andy Cohen » Tue Apr 19, 2016 3:05 am

It is now about 3 weeks since i sent you guys a file that reliably choked V1 even with R3D filament. I have yet to hear that V2 successfully prints it using eSun or any other producers filament. As such I am getting a bit worried since in the past Raise3D has shipped products which did not perform as I was led to expect... i.e., any filament.
I sure hope V2 fixed the problems I have found. Problems that have now made my N2 useless for the kind of objects i have to produce with it..
Post Reply

Return to “Hardware”

Who is online

Users browsing this forum: No registered users and 6 guests