Stock 35mm Fan Specs?

Topics around mechanical design, controller and electronics. Mods & hacks welcome.
Michael
Posts: 189
Joined: Wed Jun 22, 2016 4:59 pm
Location: West Virginia
Contact:

Stock 35mm Fan Specs?

Postby Michael » Tue Jul 26, 2016 1:36 am

Anyone happen to know the stock 35mm Fan mfg, part # or specs?


------ UPDATE ------
Raise3D stated in some posts to increase the size to 35x35x10 12V... well there are many 35x35x10 12vDC fans, with various CFM... if the goal is to increase CFM, then we need to know the spec CFM.

After a little research, the stock fans on my N2 (22-Jun-16 ordered) are:

Delta Electronics AFB03512HA 5.5CFM (0.156m³/min) 22dB @1.08W (exact replacement is Digikey PN#603-1128-ND $12.08)

AFB03512HA-A(REV01).pdf
Stock 35x35x10mm Delta Electronics 5.5 CFM Spec Sheet
(404.62 KiB) Downloaded 54 times


Actually, I am pleasantly surprised at the quality of the fan used, even if the 10mm is the spec width of the stock fan, so not really a "size" gain or an implicit airflow increase either.

To increase airflow, we needed to know the CFM.

Increased airflow options are:
Sunon 7.0 CFM (0.198m³/min) MC35101V1-000U-A99 28dB @0.72W (Digikey pn# 259-1563-ND $10.50)
Sunon 6.5 CFM (0.184m³/min) MC35101V1-000U-A99 22dB @0.52W (Digikey pn# 259-1562-ND $10.50)
NMB 5.6 CFM (0.159m³/min) 1404KL-04W-B50-B00 27dB @ 0.96W (Digikey pn# P12811-ND $15.93)

For slightly less noise:
Delta 4.5 CFM (0.127m³/min) AFB03512MA-A 18dB @ 0.60W (Digikey pn# 603-1511-ND $12.08)

Finger Fan guard is Digikey pn# CR378-ND $0.79 just in case you want 2

Granted these are just whats available at Digikey here in the US.
Last edited by Michael on Tue Jul 26, 2016 5:44 pm, edited 1 time in total.
Composite Build Plate for N2 Printers
http://www.newriver.io

User avatar
Vicky@Raise3D
Posts: 3736
Joined: Fri Mar 25, 2016 3:54 am

Re: Stock 35mm Fan Specs?

Postby Vicky@Raise3D » Tue Jul 26, 2016 6:09 am

It's a 12V, 0.14A fan.

Michael
Posts: 189
Joined: Wed Jun 22, 2016 4:59 pm
Location: West Virginia
Contact:

Re: Stock 35mm Fan Specs?

Postby Michael » Tue Jul 26, 2016 11:16 am

CFM?
Bearing?
Brushless?
Composite Build Plate for N2 Printers
http://www.newriver.io

Evan
Posts: 98
Joined: Mon Mar 21, 2016 3:07 pm

Re: Stock 35mm Fan Specs?

Postby Evan » Tue Jul 26, 2016 1:24 pm

That's not really critical. They're all comparable.

Michael
Posts: 189
Joined: Wed Jun 22, 2016 4:59 pm
Location: West Virginia
Contact:

Re: Stock 35mm Fan Specs?

Postby Michael » Tue Jul 26, 2016 5:28 pm

Raise3D stated in some posts to increase the size to 35x35x10 12V... well there are many 35x35x10 12vDC fans, with various CFM... if the goal is to increase CFM, then we need to know the spec CFM.

After a little research, the stock fans on my N2 (22-Jun-16 ordered) are:

Delta Electronics AFB03512HA 5.5CFM (0.156m³/min) 22dB @1.08W (exact replacement is Digikey PN#603-1128-ND $12.08)

AFB03512HA-A(REV01).pdf
Stock 35x35x10mm Delta Electronics 5.5 CFM Spec Sheet
(404.62 KiB) Downloaded 53 times


Actually, I am pleasantly surprised at the quality of the fan used, even if the 10mm is the spec width of the stock fan, so not really a "size" gain or an implicit airflow increase either.

To increase airflow, we needed to know the CFM.

Increased airflow options are:
Sunon 7.0 CFM (0.198m³/min) MC35101V1-000U-A99 28dB @0.72W (Digikey pn# 259-1563-ND $10.50)
Sunon 6.5 CFM (0.184m³/min) MC35101V1-000U-A99 22dB @0.52W (Digikey pn# 259-1562-ND $10.50)
NMB 5.6 CFM (0.159m³/min) 1404KL-04W-B50-B00 27dB @ 0.96W (Digikey pn# P12811-ND $15.93)

For slightly less noise:
Delta 4.5 CFM (0.127m³/min) AFB03512MA-A 18dB @ 0.60W (Digikey pn# 603-1511-ND $12.08)

Finger Fan guard is Digikey pn# CR378-ND $0.79 just in case you want 2

Granted these are just whats available at Digikey here in the US.
Composite Build Plate for N2 Printers
http://www.newriver.io

User avatar
walshlg
Posts: 1346
Joined: Wed Mar 23, 2016 12:01 pm

Re: Stock 35mm Fan Specs?

Postby walshlg » Tue Jul 26, 2016 7:27 pm

remember all fan noise readings are suspect among different manufacturers

User avatar
Casale8
Posts: 219
Joined: Fri Oct 20, 2017 5:17 pm
Location: The Real Upstate New York

Re: Stock 35mm Fan Specs?

Postby Casale8 » Mon Apr 16, 2018 7:56 pm

What's the connector part no that comes with the raise fan? I need to order the crimping tool to crimp.
-SCC
“One man's "magic" is another man's engineering. "Supernatural" is a null word.” -R.A.Heinlein


Return to “Hardware”

Who is online

Users browsing this forum: No registered users and 4 guests