Page 3 of 4

Re: STL Design Shared

Posted: Mon Jul 17, 2017 8:33 am
by firesped
I'll have to take it apart again. I modified the part by putting some thread inserts into it so the screws have something to hold onto.

the part is a square box with some holes to screw the endstop board into the shim. It has offset holes to screw the endstop board onto the back.

now that I am thinking about it. my issue is the endstop is not getting hit. I have been trying to figure out how this was corrected. the shim you posted may fix that issue but I still need the new endstops I already ordered. I'll need to get longer screws as well.

Re: STL Design Shared

Posted: Mon Jul 17, 2017 10:32 am
by Vicky@Raise3D
Sounds like very similar to the one I shared. The one I shared may be a little thicker than the one on yours. May help you problem.

Re: STL Design Shared

Posted: Tue Jul 18, 2017 12:31 am
by firesped
got my bed level and got this printed. bought some M3 x 16 screws and got it installed. it is now homing correctly.

Re: STL Design Shared

Posted: Tue Jul 18, 2017 2:34 am
by Vicky@Raise3D
Good to hear your feedback!

Re: STL Design Shared

Posted: Fri Jul 28, 2017 9:47 pm
by firesped
here is my filament runout sensor that uses the raise3d endstop.

https://www.thingiverse.com/thing:2457483

Re: STL Design Shared

Posted: Sun Aug 27, 2017 5:24 pm
by EldRick
Please add to the list. I've scaled the Raise3D-provided fan duct .stl to the same height as the post-kickstarter injection molded piece, as part of this: http://www.thingiverse.com/thing:2502206

Re: STL Design Shared

Posted: Sat Dec 23, 2017 1:18 pm
by 3DWP
I posted a dual color extruder board cover on Thingiverse so you see the Raise3d logo better: https://www.thingiverse.com/thing:2727001

Raise3DExtruderBoardCover.JPG

Re: STL Design Shared

Posted: Sat Feb 03, 2018 8:27 pm
by Noren
Edit:

I noticed that the files for the V2 fancover was shared in a previous post in this thread.

Please add them to the first post.
(Also add them to the meny with example models in IdeaMaker).

Just like we get software updates. It would be nice if Raise3D could send out “parts updates” as well. Look at how Prusa does. They are great about fixing faults or problems and communicating this to the community and make files available.

I also have a question about this "edge" on the bottom of the V2 fanduct. (see image).
I's the edge "by design"? Is it there to deflect the airflow downwards?

I haven't done any simulations on the airflow since I don't have that knowledge.
Do you have any pictures on the simulated airflow that you can share?
Just curious.

fan.jpg

Re: STL Design Shared

Posted: Mon Feb 05, 2018 3:05 am
by Vicky@Raise3D
Noren wrote:Edit:

I noticed that the files for the V2 fancover was shared in a previous post in this thread.

Please add them to the first post.
(Also add them to the meny with example models in IdeaMaker).

Just like we get software updates. It would be nice if Raise3D could send out “parts updates” as well. Look at how Prusa does. They are great about fixing faults or problems and communicating this to the community and make files available.

I also have a question about this "edge" on the bottom of the V2 fanduct. (see image).
I's the edge "by design"? Is it there to deflect the airflow downwards?

I haven't done any simulations on the airflow since I don't have that knowledge.
Do you have any pictures on the simulated airflow that you can share?
Just curious.

fan.jpg


Update done.
The "edge" is designed to be there.
One purpose is for controlling the airflow direction as you said. The other purpose is due to that it is a molding part, leaving an edge there is for keeping the wall thickness of the whole structure to be uniform.

Re: STL Design Shared

Posted: Tue Feb 13, 2018 3:23 pm
by 3DWP
I uploaded a fan mod on Thingiverse. In this setup the 35 mm fans only cool the cold end and an extra 40 mm fan on the front can cool the prints of both nozzles using gcode. Link: https://www.thingiverse.com/thing:2792586

Raise3DFanMod.jpg


This was made on my N2 Plus Dual, can somebody confirm this would fit on all N series?

Re: STL Design Shared

Posted: Tue May 08, 2018 8:57 pm
by detroitus
Hello all.
I designed a new bracket for a dial indicator for bed leveling with my N2 Dual that allows the plunger for the indicator to line up directly with the nozzles (at least along the y-axis). I thought I'd share it here if anyone else might find it useful.

It attaches where the stock cold-end fans attach, using the existing fan screws (I don't usually need cooling while bed-leveling).

https://www.thingiverse.com/thing:2900662

INDICATOR BRACKET.STL
(118.64 KiB) Downloaded 12 times

Re: STL Design Shared

Posted: Thu May 10, 2018 5:02 pm
by DrewPetitclerc

Re: STL Design Shared

Posted: Thu May 10, 2018 5:42 pm
by detroitus
DrewPetitclerc wrote:http://forum.raise3d.com/viewtopic.php?f=2&t=6460#p27120


Nice. Looks like I was thinking along the same neighborhood with my previous post.

Re: STL Design Shared

Posted: Thu May 10, 2018 5:50 pm
by detroitus
I also made an adjustable and mountable filament spool holder for the N2/N2+. It reduces unwinding friction without reducing it so much that the spool just unravels every time the extruder tugs on the filament, and it fits inside the compartment such that the door will still fully close (at least it does on my machine). Downside is you can't really mount two of these at a time, but I don't do much dual extrusion, so that didn't matter so much to me.

https://www.thingiverse.com/thing:2904055

Re: STL Design Shared

Posted: Fri Jun 15, 2018 7:39 pm
by Iamkar33m
Raise3D, can we get the STL file you use at the factory for bed level testing? Thanks!

- Kareem

Re: STL Design Shared

Posted: Fri Jun 15, 2018 7:49 pm
by EldRick
detroitus' spool holder is the only one I've found that allows you to use the common black plastic 1kg spools with the N2 door closed, without any rubbing. An excellent design.

Re: STL Design Shared

Posted: Fri Jun 15, 2018 7:56 pm
by Jetguy
Vicky@Raise3D wrote:
Jetguy wrote:Vicky, could you find the power socket cover I just posted the picture of?? I know it's 3D printed so that means somebody has the STL at the factory. Just trying to add safety for those of us with early N2 and N2Plus from the kickstarter. I had used a big piece of heatshrink to make mine safer but there is exposed mains 110 on the backside of the IEC power entry panel between the input and the fuse (the metal bus bar).
Again, earlybird N2 picture under the printer
IMG_0464[1].JPG


Here is the 3D printed version as seen on my new N2Plus
IMG_0463[1].JPG


Here it is. To install it, you need to replace the current two screws to be about M4*16, a little longer than current two.
Power Socket Cover.STL


It could be I overlooked this when searching the master list on the first post here, but could you please edit the page and ensure it's on the front master list of "official" STLs for the printer?

Re: STL Design Shared

Posted: Fri Jun 15, 2018 8:56 pm
by detroitus
EldRick wrote:detroitus' spool holder is the only one I've found that allows you to use the common black plastic 1kg spools with the N2 door closed, without any rubbing. An excellent design.


Thanks. I designed it specifically because that was driving me crazy. I had found a design for a "low friction" mount that cleared the door, but it turned out to be TOO low friction and would start spinning freely every time the filament would tug at the spool. I figured this would be a good compromise. And it SHOULD be adjustable to any spool size up to 1kg.

Re: STL Design Shared

Posted: Fri Jun 15, 2018 9:00 pm
by Casale8
I added my cover extension to thingiverse:
https://www.thingiverse.com/thing:2963119

Re: STL Design Shared

Posted: Fri Jun 15, 2018 9:00 pm
by Casale8
Casale8 wrote:I added my cover extension to thingiverse:
https://www.thingiverse.com/thing:2963119

coverextension image.JPG