Benchy3D Gcode

JuergenGK
Posts: 5
Joined: Sun Sep 02, 2018 5:56 am

Benchy3D Gcode

Postby JuergenGK » Sat Sep 15, 2018 6:57 pm

:roll: hello all,

Since yesterday I call the Pro2 myown. It is my 5th FDM Printer. Since yesterday I unsuccessfully try to print the Benchy3D model. With the template HIGH PLA PRO2 there is no result to be achieved (neither with the Raise3D nor Verbatim PLA). There seem to occur several Layers with underextrusion, where you simply can remove the material with a fingernail or the material collapses during printing.

I won‘t deny to make a mistake. But in the case of a 4K pricing 3D printer, I assume there should be a user friendly solution, before I return the machine to my Reseller. Does anybody of you provide a workable gcode file, which I can test?

Thank you

Juergen

User avatar
Vicky@Raise3D
Posts: 4564
Joined: Fri Mar 25, 2016 3:54 am

Re: Benchy3D Gcode

Postby Vicky@Raise3D » Mon Sep 17, 2018 7:14 pm

Would you like to test Raise3D PLA with the following Gcode and share us the print results with pictures?
It's a very quick testing cube, we'd like to help check whether you will have any extrusion issue with this part with Raise3D PLA. As we are more familiar with the result it can achieve.
20mm_Calibration_Box.rar
(29.87 KiB) Downloaded 24 times

JuergenGK
Posts: 5
Joined: Sun Sep 02, 2018 5:56 am

Re: Benchy3D Gcode

Postby JuergenGK » Mon Sep 17, 2018 7:35 pm

Hello Vicky,

Willco this tomorrow morning and post the pictures here.

Thanks

Juergen

JuergenGK
Posts: 5
Joined: Sun Sep 02, 2018 5:56 am

Re: Benchy3D Gcode

Postby JuergenGK » Tue Sep 18, 2018 11:08 am

Dear Vicky,

thank you for the file. I tried it with the same problems. But then I got the solution, forced by my dispair. The Display showed me for the Motion Controller Board the firmware version 0-0-36. I flashed the Controller with the version 0-0-31 from your download page and afterwards everything worked fine!

User avatar
Vicky@Raise3D
Posts: 4564
Joined: Fri Mar 25, 2016 3:54 am

Re: Benchy3D Gcode

Postby Vicky@Raise3D » Tue Sep 18, 2018 11:42 pm

Thanks for your update! Good to know the result.

dm7864
Posts: 7
Joined: Tue Sep 11, 2018 1:42 pm

Re: Benchy3D Gcode

Postby dm7864 » Wed Sep 19, 2018 1:09 pm

So you flashed back to an older version firmware on the controller board

JuergenGK
Posts: 5
Joined: Sun Sep 02, 2018 5:56 am

Re: Benchy3D Gcode

Postby JuergenGK » Sat Sep 22, 2018 7:55 am

Yes I did,

With the delivered version the movements of the Extruder were far to fast and the filament Feed drive unreliable.

Ronvp
Posts: 52
Joined: Tue Jul 17, 2018 9:07 pm

Re: Benchy3D Gcode

Postby Ronvp » Sat Sep 22, 2018 12:29 pm

As far as I can tell 0-0-31 is the latest version.. He may have had some testing firmware on it..


Return to “Pro2 Series”

Who is online

Users browsing this forum: No registered users and 1 guest