Print After 3 4 houres stuck, Jam bad quality

Prop-Fiction
Posts: 58
Joined: Fri Jun 15, 2018 10:39 pm

Print After 3 4 houres stuck, Jam bad quality

Postby Prop-Fiction » Thu Aug 09, 2018 7:56 pm

Hello,
again have a new problem.
I have not been able to print for one week. All attempts end after 3 to 4 hours.
The printer is constantly making clicks.
The quality of the print is underground and it prints extremely dirty.
everything cleaned and adjusted.
after 4 to 5 cm pressure he spins. I have to say slowly I'm not bothered anymore. if I do not get the problem quickly in the grip he goes on ebay.
have tried different models always with the same result. first sporadic click then more often then he promotes no more pressure over.
can not be slow anymore. solved a problem and the next one comes.
Es gibt kein das „geht nicht“, immer nur eine Frage des Geldes oder der Zeit.

Schlaf wird überbewertet.

My Costume website
http://www.prop-fiction.de

Prop-Fiction
Posts: 58
Joined: Fri Jun 15, 2018 10:39 pm

Re: Print After 3 4 houres stuck, Jam bad quality

Postby Prop-Fiction » Thu Aug 09, 2018 8:40 pm

By the way, he has been pulling threads recently and occasionally does not print some layers. Probably because he does not transport the filmmaker.
I have not changed any settings.
Es gibt kein das „geht nicht“, immer nur eine Frage des Geldes oder der Zeit.

Schlaf wird überbewertet.

My Costume website
http://www.prop-fiction.de

User avatar
Vicky@Raise3D
Posts: 3937
Joined: Fri Mar 25, 2016 3:54 am

Re: Print After 3 4 houres stuck, Jam bad quality

Postby Vicky@Raise3D » Fri Aug 10, 2018 12:54 am

May I ask how many modifications you have already done with this printer by now? It may help us to analysis the situation.

Prop-Fiction
Posts: 58
Joined: Fri Jun 15, 2018 10:39 pm

Re: Print After 3 4 houres stuck, Jam bad quality

Postby Prop-Fiction » Fri Aug 10, 2018 7:18 am

Only the Model cooling and the OKM Stepper Cooling .
But with this it run over 2 weeks perfect.
No problems but now.
Nothing changed.
It’s really disappointing
Es gibt kein das „geht nicht“, immer nur eine Frage des Geldes oder der Zeit.

Schlaf wird überbewertet.

My Costume website
http://www.prop-fiction.de

User avatar
Vicky@Raise3D
Posts: 3937
Joined: Fri Mar 25, 2016 3:54 am

Re: Print After 3 4 houres stuck, Jam bad quality

Postby Vicky@Raise3D » Fri Aug 10, 2018 11:57 pm

Would you like to contact us via support ticket and list the modifications you have done by now, the filament you are currently having trouble with and fill the basic information of your printer here (help.raise3d.com) needs?
We are currently testing clogging and different filament and different options on Pro2. We want to get more information from you and help you to solve your issues as well.

Prop-Fiction
Posts: 58
Joined: Fri Jun 15, 2018 10:39 pm

Re: Print After 3 4 houres stuck, Jam bad quality

Postby Prop-Fiction » Sat Aug 11, 2018 12:32 am

hey, luckily i found the solution.
I telephoned yesterday with OKM, the German distributor of Raise3d.
I have spoken to someone who really has some idea. This told me that this error is an Idea Maker problem.
This error occurs on more complicated models with larger mesh date.
but not fundamentally, but partly in certain areas of a model.
it was explained to me roughly with the withdrawal of the material.
the program overwhelms the device.
I have made two changes as OKM and now everything is back Top.
even models that I did not get printed.
to the changes:
in the profile settings, I have changed the following.
Advanced settings:
extruder;
Minimal Travel of Retraction. set to 4mm.
and
ooze:
Avoid Retraction Inside Model
Hacking must be in there.
everything is now ..
I can only say OKM Helps really great!
who still has problems should try this attitude times ..
Es gibt kein das „geht nicht“, immer nur eine Frage des Geldes oder der Zeit.

Schlaf wird überbewertet.

My Costume website
http://www.prop-fiction.de

User avatar
Vicky@Raise3D
Posts: 3937
Joined: Fri Mar 25, 2016 3:54 am

Re: Print After 3 4 houres stuck, Jam bad quality

Postby Vicky@Raise3D » Tue Aug 14, 2018 12:18 am

Increase the minimal travel retraction value will decrease the retraction quantity.
Please also will increase the strings and oozing on small features which are close to other features around, under 4mm.


Return to “Pro2 Series”

Who is online

Users browsing this forum: No registered users and 1 guest