Search found 844 matches

by firesped
Fri Mar 30, 2018 8:21 pm
Forum: Feature requests, ideas, wishes
Topic: Raise3D Fan Duct Pro2 Plus
Replies: 22
Views: 1251

Re: Raise3D Fan Duct Pro2 Plus

my next design was going that direction with forward cold end cooling. I don't think that exact design will be compatible with the older printers though. I've always kind of seen it as an issue to blow the air in from the sides as it creates a wall of force in the model and now the heat just sits th...
by firesped
Fri Mar 30, 2018 8:06 pm
Forum: Hardware
Topic: Retrofit N2 with Pro series features
Replies: 34
Views: 2269

Re: Retrofit N2 with Pro series features

I'd hate to see the cost to retrofit the old ones. you are likely looking at a couple grand to do it.
by firesped
Thu Mar 08, 2018 10:25 pm
Forum: Hardware
Topic: Octoprint and hacking the touch screen?
Replies: 5
Views: 397

Re: Octoprint and hacking the touch screen?

There is octoprint on the touchscreen however it is an older version and can not be updated. (I have tried). I openned a support ticket but it has become stall and forgotten at this point. Until i have my side project done, I don't feel comfortable trying to get it fixed which would likely require m...
by firesped
Tue Feb 27, 2018 6:18 pm
Forum: Hardware
Topic: N1 Fan Mods
Replies: 11
Views: 599

Re: N1 Fan Mods

There are features to turn on the cold end fans when it is heating but we would need to know the pinout of those fans, if they are connected to the processor or not.
by firesped
Mon Feb 26, 2018 11:03 pm
Forum: Hardware
Topic: E3D v6 Adaptor
Replies: 150
Views: 10700

Re: E3D v6 Adaptor

the 40mm is actually a smaller fan then the part is currently.
by firesped
Mon Feb 26, 2018 8:57 pm
Forum: Hardware
Topic: E3D v6 Adaptor
Replies: 150
Views: 10700

Re: E3D v6 Adaptor

I have a really good setup with my current design but it only works with the volcano. I ordered 40mm x 40mm x 20 mm blower fan to redesign it. I am hoping that it will allow me to create a unit that can cool both hotends.
by firesped
Sat Feb 17, 2018 9:36 pm
Forum: Software
Topic: LIN_ADVANCE = better extrusion control
Replies: 86
Views: 6069

Re: LIN_ADVANCE = better extrusion control

the lack material code I modified from raises version is controllable via gcode. both turn it off or on and to change the PIN readings. the difference between this version and the marlin 1.1.0 version is that it now uses the endstop gcodes versus a custom gcode. M119 will report status, M120 turns t...
by firesped
Sat Feb 17, 2018 8:56 pm
Forum: Software
Topic: ideaMaker 3.1.0 Release Note
Replies: 61
Views: 5084

Re: ideaMaker 3.1.0 Release Note

I see I can change it now to higher amounts. when I dupilicated the printer, it was limited 1.0 mm max however.
by firesped
Sat Feb 17, 2018 2:39 am
Forum: Software
Topic: ideaMaker 3.1.0 Release Note
Replies: 61
Views: 5084

Re: ideaMaker 3.1.0 Release Note

was trying to setup a printer that has a 1.2mm nozzle. ideamaker would not let me enter a nozzle size bigger then 1.0mm
by firesped
Wed Feb 07, 2018 4:08 am
Forum: General
Topic: Shifting Forward and Backwards.
Replies: 53
Views: 7657

Re: Shifting Forward and Backwards.

There is no way to upgrade the Marlin board. It is a custom RUMBA type board that used a custom remote extruder board. No other board on the market is compatible with that remote extruder board. and I did try. Raise3D would have to design a new drop in board with a 32 bit processor on it. Which is l...
by firesped
Tue Feb 06, 2018 1:27 pm
Forum: Software
Topic: MID PRINT FILAMENT LOADING
Replies: 5
Views: 732

Re: MID PRINT FILAMENT LOADING

with the updated firmware on the motion controller. the filament runout sensor will detect that the printer is running out of filament. It sends a single to the touchscreen to pause the print. The touchscreen also knows it was paused by this process. Whenever you pause or stop the printer. it has to...
by firesped
Tue Feb 06, 2018 1:43 am
Forum: Software
Topic: LIN_ADVANCE = better extrusion control
Replies: 86
Views: 6069

Re: LIN_ADVANCE = better extrusion control

If you have a single extruder. That could also be causing an issue due to the expected format not outputting for the hotends. the firmware won't display the T0: current temp / target temp line. I need to fix that. Do you have a single extruder?
by firesped
Tue Feb 06, 2018 1:13 am
Forum: Software
Topic: LIN_ADVANCE = better extrusion control
Replies: 86
Views: 6069

Re: LIN_ADVANCE = better extrusion control

My original fork was released around a year ago. The new one is updated to function with the procedures of marlin. M190 is not 100% the same and I think M109 adds the D stamp at the end of the output. M105 outputs the same. M190 outputs the same starting calls then outputs the M105 calls after that....
by firesped
Tue Feb 06, 2018 12:12 am
Forum: Software
Topic: LIN_ADVANCE = better extrusion control
Replies: 86
Views: 6069

Re: LIN_ADVANCE = better extrusion control

What sensor do you have on the bed?
by firesped
Tue Feb 06, 2018 12:03 am
Forum: Software
Topic: the version of github contains errors
Replies: 3
Views: 311

Re: the version of github contains errors

the other possibility is that the 1.1.6-rev1 is actually 1.1.6-rev2 (lack of material firmware). You would need to have a filament runout sensor on it and see if it works. That firmware does not have the ability to turn on or off the sensor or change it from open or closed pin reading. if it is that...
by firesped
Thu Feb 01, 2018 12:02 am
Forum: Hardware
Topic: cause of slipping filament
Replies: 23
Views: 1292

Re: cause of slipping filament

I would think, if you replace the drive gears with the ones Jetguy suggests, you should align the motor with the new gears. another simple inexpensive "mod" I have seen people do is install washers to cant the extruder motor slightly for a better grip as well. personally, i got seriously f...
by firesped
Tue Jan 30, 2018 7:47 pm
Forum: Software
Topic: LIN_ADVANCE = better extrusion control
Replies: 86
Views: 6069

Re: LIN_ADVANCE = better extrusion control

Now I can post this. finally worked on the raisetouch Pull Request. user-friend firmware for the N-Series is here. https://github.com/Firesped/Marlin/tree/raisetouch-Raise3D Designed to be configured like the Raise3D firmware is. Easy settings in the beginning of the configuration file with document...
by firesped
Tue Jan 30, 2018 4:12 pm
Forum: Hardware
Topic: Project: The next heated bed
Replies: 30
Views: 4815

Re: Project: The next heated bed

I've had no issues with cracks with the ePC i've been using.
by firesped
Tue Jan 30, 2018 4:10 pm
Forum: Software
Topic: Touchscreen Firmware 0.9.7 Release Note 2018.1.16
Replies: 63
Views: 5616

Re: Touchscreen Firmware 0.9.7 Release Note 2018.1.16

I'm not sure it is giving an error message. The file just was not there. I started moving them from the place I was saving it. I'll have to try and repeat to lock down the issue.
by firesped
Tue Jan 30, 2018 12:08 am
Forum: Software
Topic: Touchscreen Firmware 0.9.7 Release Note 2018.1.16
Replies: 63
Views: 5616

Re: Touchscreen Firmware 0.9.7 Release Note 2018.1.16

the touchscreen seems to not like to allow more then 2 or 3 logs to be saved to a USB stick. It fails to output the files.

Go to advanced search