Search found 1349 matches

by walshlg
Mon Oct 02, 2017 4:33 pm
Forum: Hardware
Topic: thermal runaway protection
Replies: 14
Views: 2877

Re: thermal runaway protection

btw going to epoxy over exposed wires, too close to pins!
by walshlg
Mon Oct 02, 2017 12:46 am
Forum: Others
Topic: Cyanoacrylate (Super Glue) to greatly improve adhesion
Replies: 11
Views: 1837

Re: Cyanoacrylate (Super Glue) to greatly improve adhesion

Nice experiment. Will be interesting to see if it builds up over time
by walshlg
Mon Oct 02, 2017 12:44 am
Forum: Feature requests, ideas, wishes
Topic: N2 stops printing
Replies: 2
Views: 909

Re: N2 stops printing

Yes check slice preview to make sure its slicing correctly
by walshlg
Mon Oct 02, 2017 12:42 am
Forum: Feature requests, ideas, wishes
Topic: why are the electrical connectors glued into place?
Replies: 9
Views: 1370

Re: why are the electrical connectors glued into place?

Yeh, the big problem is that the latch for these high current connectors doesnt latch properly
by walshlg
Mon Oct 02, 2017 12:39 am
Forum: Software
Topic: Remarkable new feature in Slic3r - Adaptive Layer Height
Replies: 7
Views: 1582

Re: Remarkable new feature in Slic3r - Adaptive Layer Height

And print Inner shells first when edges slope out (bottom of a sphere) and print outer layer first at the top where edge slopes in. Doing this may eliminate the need for fill.
by walshlg
Mon Oct 02, 2017 12:34 am
Forum: General
Topic: Bed Leveling - N2+ (My Experience & Solution)
Replies: 22
Views: 4761

Re: Bed Leveling - N2+ (My Experience & Solution)

Ahh, I misunderstood! I put the springs between the bed frame and the heated bed. Sometimes it leaves no tension on the center screw!
by walshlg
Mon Oct 02, 2017 12:29 am
Forum: Hardware
Topic: thermal runaway protection
Replies: 14
Views: 2877

Re: thermal runaway protection

Hate soldering on pc boards, seems they also use a higher melting pt solder. Spent an hour practicing and my heat shrink is terrible. Suggest- do not try this without a solder sucker. Here is my layout:

20171001_183941.jpg
by walshlg
Sun Oct 01, 2017 8:42 pm
Forum: General
Topic: Bed Leveling - N2+ (My Experience & Solution)
Replies: 22
Views: 4761

Re: Bed Leveling - N2+ (My Experience & Solution)

excellent work. My only suggestion is to make the spring in the center stronger (2x higher spring constant) since it is trying to push up against all the screws around the outer edge pulling down.
by walshlg
Sun Oct 01, 2017 8:38 pm
Forum: General
Topic: Not sticking, powder printing.
Replies: 14
Views: 2267

Re: Not sticking, powder printing.

a tip I got from the folks at raise: An easy way to dry prints is to put them on the bed, covered by a regular cardboard box and leave the bed on 60C overnight.
by walshlg
Sun Oct 01, 2017 8:36 pm
Forum: Hardware
Topic: How to quiet Noisy Fans?
Replies: 10
Views: 2242

Re: How to quiet Noisy Fans?

Gotta tell you, I mod computers and fans are funky, you never know when you are going to get a bad one. I always keep spares on hand
by walshlg
Fri Sep 29, 2017 5:24 pm
Forum: General
Topic: Not sticking, powder printing.
Replies: 14
Views: 2267

Re: Not sticking, powder printing.

fwiw try drying a roll and see if it improves printing
by walshlg
Thu Sep 28, 2017 10:17 pm
Forum: User's Gallery
Topic: Patterns for Aluminium Sand Casting
Replies: 56
Views: 11135

Re: Patterns for Aluminium Sand Casting

awesome stuff
by walshlg
Thu Sep 28, 2017 10:15 pm
Forum: Hardware
Topic: How to quiet Noisy Fans?
Replies: 10
Views: 2242

Re: How to quiet Noisy Fans?

wow, well I think replacing the fans might be a good step, also make sure housing isn't touching them
by walshlg
Wed Sep 27, 2017 2:52 pm
Forum: Hardware
Topic: Bed auto-leveling mod?
Replies: 2
Views: 780

Re: Bed auto-leveling mod?

AFAIK The "leveling" sensors actually just measure and map the bed height differences and that is then included in the g-code
by walshlg
Wed Sep 27, 2017 11:53 am
Forum: Software
Topic: Print slow, me or Idea?
Replies: 5
Views: 993

Re: Print slow, me or Idea?

any settings in firmware are not known to the slicer and will always override your g-code. This is an interesting problem. May I suggest that you send the model and g-code to Vicky to let raise analyze it?
by walshlg
Mon Sep 25, 2017 8:49 pm
Forum: Software
Topic: Print slow, me or Idea?
Replies: 5
Views: 993

Re: Print slow, me or Idea?

oh and make sure z-hop is zero - had bumped that once and it almost doubled my print time
by walshlg
Mon Sep 25, 2017 8:48 pm
Forum: Software
Topic: Print slow, me or Idea?
Replies: 5
Views: 993

Re: Print slow, me or Idea?

deceleration speed may be coming into play. IIRC that is set in firmware.
by walshlg
Tue Sep 19, 2017 3:32 pm
Forum: Software
Topic: No Template files on Ubuntu install
Replies: 5
Views: 991

Re: No Template files on Ubuntu install

usually no settings mean that you haven't selected a printer in printer settings
by walshlg
Tue Sep 19, 2017 3:30 pm
Forum: General
Topic: Looking at a Raise3D N2 (non-plus)
Replies: 5
Views: 1103

Re: Looking at a Raise3D N2 (non-plus)

fwiw - I use several types of 3d printers. All of them clog occasionally, no way around that using fdm. I did the bed mod with the springs and thumb screws - big improvement if you need to print thin or big items. As opposed to others, I reset Z frequently depending on what I am printing and how muc...
by walshlg
Mon Sep 18, 2017 7:02 pm
Forum: Hardware
Topic: thermal runaway protection
Replies: 14
Views: 2877

Re: thermal runaway protection

Thanks, I get that in place when board arrives

Go to advanced search