Search found 72 matches

by mark_3d
Thu Aug 02, 2018 3:47 pm
Forum: Hardware
Topic: Pro buildplate
Replies: 10
Views: 475

Re: Pro buildplate

No, there is no guide to install to N series because it's not listed as a compatible upgrade. We asked for it and Raise 3D refuses to sell it and all required components as an upgrade package. As such, there is not yet a DIY tutorial because to my knowledge, they only just even listed that part for...
by mark_3d
Thu Aug 02, 2018 12:07 pm
Forum: Hardware
Topic: Pro buildplate
Replies: 10
Views: 475

Pro buildplate

What Is the pro build plate made of? Has it a glass? There is a guide to install the pro plate on the non pro series?
by mark_3d
Thu Aug 02, 2018 11:15 am
Forum: General
Topic: Buildplate Glass Brake
Replies: 2
Views: 453

Buildplate Glass Brake

It's happen to me that after a big print was finished the blass was curved and when i tried to remove the printed part, the glass brake. I usually use dimafix and was printing abs x. It could be tension between the printed part and the glass?
by mark_3d
Mon Jul 30, 2018 10:04 pm
Forum: Printing Settings
Topic: Part made of different pices
Replies: 5
Views: 224

Re: Part made of different pices

There is a tool to convert the model in a single object with only external walls?
by mark_3d
Mon Jul 30, 2018 5:33 pm
Forum: Printing Settings
Topic: Part made of different pices
Replies: 5
Views: 224

Part made of different pices

I have a part that is made of different pices and after printed that it will brake easily. The second image shows how simplify slice the model, and the secondo how cura slice the model. I whant to achive the cura result in simplify.
by mark_3d
Mon Jul 23, 2018 5:50 pm
Forum: Printing Settings
Topic: Abs 70° overhang
Replies: 0
Views: 159

Abs 70° overhang

This is the result I get printing abs at 70° overhang 30mm heigh I think it came out pretty good.
by mark_3d
Fri Jul 20, 2018 1:43 pm
Forum: General
Topic: Y noise
Replies: 1
Views: 364

Y noise

At 14s you heard a awkward noise. This is the extruder moving on y axis. Do I need to lubricate the axis with silicon grease ?
by mark_3d
Thu Jul 19, 2018 8:59 pm
Forum: General
Topic: Heatblock isolation
Replies: 6
Views: 330

Re: Heatblock isolation

Ok thanks. Tomorrow I will try a print.
by mark_3d
Thu Jul 19, 2018 8:49 pm
Forum: General
Topic: Heatblock isolation
Replies: 6
Views: 330

Re: Heatblock isolation

Just as a double check since you have messed with the hotend system, it did start at room temp and you did observe the temp rise to 200C? Then when you stopped, you also saw it cool down and the reported temp dropped correctly? Just want to ensure we are not in thermal runaway from a temp sensor fa...
by mark_3d
Thu Jul 19, 2018 8:46 pm
Forum: General
Topic: Heatblock isolation
Replies: 6
Views: 330

Re: Heatblock isolation

I hope that. I have unmounted the isolation and there aren't any burn to see. But I was worried about the smoke coming out.
by mark_3d
Thu Jul 19, 2018 8:02 pm
Forum: General
Topic: Heatblock isolation
Replies: 6
Views: 330

Heatblock isolation

I mounted this isolation as shown in the image below. When the temperature arrive around 200°c it start to smoke. What should I do and why it start to smoke?
by mark_3d
Wed Jul 11, 2018 6:38 pm
Forum: Hardware
Topic: Heatblock isolation
Replies: 2
Views: 176

Heatblock isolation

Has anyone a better idea than this shown in the picture below?
by mark_3d
Mon Jul 09, 2018 8:29 pm
Forum: Hardware
Topic: N2 Psu Fan
Replies: 7
Views: 527

Re: N2 Psu Fan

which direction has the psu fan airflow? is it blowing the air from the outside to the inside or from the inside to the outside?
by mark_3d
Fri May 25, 2018 7:45 pm
Forum: General
Topic: new heat block
Replies: 1
Views: 981

new heat block

I installed a new heat block and the filament comes out from two places as shown in the image below.
by mark_3d
Tue May 08, 2018 1:57 pm
Forum: Hardware
Topic: Improvements by using TMC2130 driver.
Replies: 82
Views: 9552

Re: Improvements by using TMC2130 driver.

I have installed the SD2224 driver on x y and z. The z is very silent but x and y make some noise. More than the stock driver. I set the switch as shown on the previous post.
by mark_3d
Mon May 07, 2018 8:35 am
Forum: Feature requests, ideas, wishes
Topic: Adjusting Z height while printing
Replies: 6
Views: 485

Re: Adjusting Z height while printing

Z height? You mean layer height or distance between nozzle and build plate? Yes I mean adjusting Tha gap between the nozzle and the build plate. So if you start a print and see that you need to adjust The gap you will be able to do it live without stopping the print and adjusting manually the bed h...
by mark_3d
Mon Apr 23, 2018 8:43 pm
Forum: Hardware
Topic: Improvements by using TMC2130 driver.
Replies: 82
Views: 9552

Re: Improvements by using TMC2130 driver.

i inverted the two wire on one side and now ist works correctly.
by mark_3d
Mon Apr 23, 2018 8:35 pm
Forum: Hardware
Topic: Improvements by using TMC2130 driver.
Replies: 82
Views: 9552

Re: Improvements by using TMC2130 driver.

i try reversing the two external wire of the connector, but the z axis move only in one direction and do a lot of noise.
by mark_3d
Mon Apr 23, 2018 8:17 pm
Forum: Hardware
Topic: Improvements by using TMC2130 driver.
Replies: 82
Views: 9552

Re: Improvements by using TMC2130 driver.

I installed 3 SD2224. X Y and Z. only the Z axis moves backwards. what should i do?
by mark_3d
Fri Apr 20, 2018 3:23 pm
Forum: Feature requests, ideas, wishes
Topic: Adjusting Z height while printing
Replies: 6
Views: 485

Adjusting Z height while printing

The ability to adjust the Z height from the lcd screen while printing.

Go to advanced search