Search found 61 matches

by mark_3d
Wed Jul 11, 2018 6:38 pm
Forum: Hardware
Topic: Heatblock isolation
Replies: 2
Views: 102

Heatblock isolation

Has anyone a better idea than this shown in the picture below?
by mark_3d
Mon Jul 09, 2018 8:29 pm
Forum: Hardware
Topic: N2 Psu Fan
Replies: 7
Views: 396

Re: N2 Psu Fan

which direction has the psu fan airflow? is it blowing the air from the outside to the inside or from the inside to the outside?
by mark_3d
Fri May 25, 2018 7:45 pm
Forum: General
Topic: new heat block
Replies: 1
Views: 947

new heat block

I installed a new heat block and the filament comes out from two places as shown in the image below.
by mark_3d
Tue May 08, 2018 1:57 pm
Forum: Hardware
Topic: Improvements by using TMC2130 driver.
Replies: 82
Views: 7517

Re: Improvements by using TMC2130 driver.

I have installed the SD2224 driver on x y and z. The z is very silent but x and y make some noise. More than the stock driver. I set the switch as shown on the previous post.
by mark_3d
Mon May 07, 2018 8:35 am
Forum: Feature requests, ideas, wishes
Topic: Adjusting Z height while printing
Replies: 6
Views: 356

Re: Adjusting Z height while printing

Z height? You mean layer height or distance between nozzle and build plate? Yes I mean adjusting Tha gap between the nozzle and the build plate. So if you start a print and see that you need to adjust The gap you will be able to do it live without stopping the print and adjusting manually the bed h...
by mark_3d
Mon Apr 23, 2018 8:43 pm
Forum: Hardware
Topic: Improvements by using TMC2130 driver.
Replies: 82
Views: 7517

Re: Improvements by using TMC2130 driver.

i inverted the two wire on one side and now ist works correctly.
by mark_3d
Mon Apr 23, 2018 8:35 pm
Forum: Hardware
Topic: Improvements by using TMC2130 driver.
Replies: 82
Views: 7517

Re: Improvements by using TMC2130 driver.

i try reversing the two external wire of the connector, but the z axis move only in one direction and do a lot of noise.
by mark_3d
Mon Apr 23, 2018 8:17 pm
Forum: Hardware
Topic: Improvements by using TMC2130 driver.
Replies: 82
Views: 7517

Re: Improvements by using TMC2130 driver.

I installed 3 SD2224. X Y and Z. only the Z axis moves backwards. what should i do?
by mark_3d
Fri Apr 20, 2018 3:23 pm
Forum: Feature requests, ideas, wishes
Topic: Adjusting Z height while printing
Replies: 6
Views: 356

Adjusting Z height while printing

The ability to adjust the Z height from the lcd screen while printing.
by mark_3d
Fri Apr 13, 2018 1:33 pm
Forum: Hardware
Topic: Quieting the N2
Replies: 23
Views: 1145

Re: Quieting the N2

Or I could connect 2 12v fans to the 24v port.
by mark_3d
Fri Apr 13, 2018 11:30 am
Forum: Hardware
Topic: Quieting the N2
Replies: 23
Views: 1145

Re: Quieting the N2

And here's a picture of a 120v 80mm fan grafted on to the outside of the power supply. It is always on, so it makes a small amount of noise all on its own, but the internal fan on the power supply doesn't run as often, so the net is less racket. I can even hear the steppers and extruder now. I was ...
by mark_3d
Fri Apr 13, 2018 6:59 am
Forum: Hardware
Topic: N2 Psu Fan
Replies: 7
Views: 396

Re: N2 Psu Fan

And where to connect the additional fan? Is a 12v port inside the psu?
by mark_3d
Fri Apr 13, 2018 5:05 am
Forum: Hardware
Topic: N2 Psu Fan
Replies: 7
Views: 396

Re: N2 Psu Fan

I have a single fan temp controlled. Why not replaceing it instead of adding one?
by mark_3d
Thu Apr 12, 2018 10:16 pm
Forum: Hardware
Topic: N2 Psu Fan
Replies: 7
Views: 396

Re: N2 Psu Fan

EldRick wrote:http://forum.raise3d.com/viewtopic.php?f=4&t=6377

I want to replace the existing psu fan. Anyone does this?
by mark_3d
Thu Apr 12, 2018 8:34 pm
Forum: Hardware
Topic: N2 Psu Fan
Replies: 7
Views: 396

N2 Psu Fan

I want to replace the psu fan with a more silent fan. I saw that the stock fan is a 80mm by 25mm. What kind of fan is the stock fan? rpm? CFM?
by mark_3d
Thu Apr 12, 2018 6:45 pm
Forum: Hardware
Topic: Gcode controlled fan
Replies: 5
Views: 272

Re: Gcode controlled fan

i think the first. i will try to connect to the second port.
by mark_3d
Wed Apr 11, 2018 10:18 pm
Forum: Hardware
Topic: Gcode controlled fan
Replies: 5
Views: 272

Re: Gcode controlled fan

I only set the fan % in the simplify fan speed tab. I will try what you suggest.
by mark_3d
Wed Apr 11, 2018 9:56 pm
Forum: Hardware
Topic: Single extruder fan duct for a 40mm fan
Replies: 5
Views: 906

Re: Single extruder fan duct for a 40mm fan

So everything is working fine and i had some time to look at that big ugly part cooling fan on my N1. I already had a 40mm fan lying around as spare for my Clone R1 so i decided to use it with a new fan duct. Airflow on this one is alot closer to the nozzle and works fine with my other printer. I a...
by mark_3d
Wed Apr 11, 2018 9:24 pm
Forum: Hardware
Topic: Gcode controlled fan
Replies: 5
Views: 272

Re: Gcode controlled fan

If i connect the fan to the always on connector, the fan works.
by mark_3d
Wed Apr 11, 2018 8:32 pm
Forum: Hardware
Topic: Gcode controlled fan
Replies: 5
Views: 272

Gcode controlled fan

I connect the fan to the gcode controlled pwm but the fan didn't turn on.
head breakout2.jpg
head breakout2.jpg (30.06 KiB) Viewed 272 times

Go to advanced search