Search found 2352 matches

by Jetguy
Thu May 24, 2018 3:54 pm
Forum: Printing Settings
Topic: Problems with vase mode
Replies: 14
Views: 143

Re: Problems with vase mode

Oh heck, I just realized after looking at the printer in the background, this isn't even a Raise 3D printer. I'm all for helping folks, but come on man, this is your printer crapping out. Not even a fair comparison. We have no baseline of your firmware, if you were printing over USB or Octoprint, t...
by Jetguy
Thu May 24, 2018 3:46 pm
Forum: Printing Settings
Topic: Problems with vase mode
Replies: 14
Views: 143

Re: Problems with vase mode

Now I did print the sample gcode on my N1 (even though the file is made for a larger printer, in this case, it still fits) and did not get any artifacts, but you could definitely hear the segments. My thought is that if you used any feedrate multiplier, then the risk for hitting that limit increases...
by Jetguy
Thu May 24, 2018 1:31 pm
Forum: Printing Settings
Topic: Problems with vase mode
Replies: 14
Views: 143

Re: Problems with vase mode

Hi, I'm 99.9% sure these are the files I used. I could check by printing again, but my printer is already busy with a job tonight. It must be something really weird in the gcode as I could easily hear it when it got to that point. Instead of nice smooth stepper motor whine, it had a weird vibrato t...
by Jetguy
Thu May 24, 2018 1:26 pm
Forum: Printing Settings
Topic: Problems with vase mode
Replies: 14
Views: 143

Re: Problems with vase mode

Again, detail gcode preview in S3D lets us see how many segments (lines) in a given area. What I did here is first adjust to the height or region in the model where we see the error in your print. Suttering gcode preview1.jpg Next, I enable a line count in this region, and set it to 100 to observe t...
by Jetguy
Thu May 24, 2018 12:52 pm
Forum: Printing Settings
Topic: Problems with vase mode
Replies: 14
Views: 143

Re: Problems with vase mode

Any news? Sorry, I only just saw that you uploaded the gcode. A preview of that gcode using Simplify 3D (a much more feature rich slicer that you pay for, not for free) shows no errors in the gcode. By errors, I mean speed changes or other errant paths. So what that means is? You said the key word ...
by Jetguy
Wed May 23, 2018 4:01 pm
Forum: Hardware
Topic: Filament Run-out Sensor Add-on
Replies: 68
Views: 3012

Re: Filament Run-out Sensor Add-on

I would be really curious to see if there there any difference in the result of the open source community made FSR firmware VS the Raise 3D FSR firmware. The Raise 3D sensor should work with both, it might just take a little testing to understand the correct options within the open source firmware. ...
by Jetguy
Tue May 22, 2018 3:39 pm
Forum: Feature requests, ideas, wishes
Topic: Hardware Suggestion - Filament Clog or Binding Sensing
Replies: 8
Views: 101

Re: Hardware Suggestion - Filament Clog or Binding Sensing

Didn't expect you write anything up. Assumed there may have been something already done. Thanks again! Sorry, again, just stating the why behind exactly why that (wiring diagram and instructions) didn't exist. #1 we waited for the official firmware side of this just recently released (diy solution ...
by Jetguy
Tue May 22, 2018 3:18 pm
Forum: Feature requests, ideas, wishes
Topic: Hardware Suggestion - Filament Clog or Binding Sensing
Replies: 8
Views: 101

Re: Hardware Suggestion - Filament Clog or Binding Sensing

The reason this had not really been done to this point, until Raise 3D released both a standard Raisepack that supported filament detection pause and the matching FSR firmware update, this was not as practical for the user to install. Actually, we hoped this was the system Raise 3D would have gone w...
by Jetguy
Tue May 22, 2018 3:16 pm
Forum: Feature requests, ideas, wishes
Topic: Hardware Suggestion - Filament Clog or Binding Sensing
Replies: 8
Views: 101

Re: Hardware Suggestion - Filament Clog or Binding Sensing

Also, there is an alternate and maybe easier set of labeled pins to get the required 5V and ground from on the mainboard.
Alternate 5V connection point.jpg
by Jetguy
Tue May 22, 2018 3:08 pm
Forum: Feature requests, ideas, wishes
Topic: Hardware Suggestion - Filament Clog or Binding Sensing
Replies: 8
Views: 101

Re: Hardware Suggestion - Filament Clog or Binding Sensing

Well, obviously I haven't done it yet since i just typed that answer, but here is where it's going to come from. https://www.raise3d.com/pages/filament-run-out-sensor-installation-instruction Specifically, pay attention here to the factory supplied wiring harness. Like I said before, this is 4 simpl...
by Jetguy
Tue May 22, 2018 2:28 pm
Forum: Hardware
Topic: E3D v6 Adaptor
Replies: 134
Views: 8920

Re: E3D v6 Adaptor

Finally getting around to installing the adapter and I’m interested in trying the Berd-air. If I buy it, do I need the eSwitch adapter of can I plug directly into the 24v? If you get the 24V version of the Berd air cooler, then yes, you can make a connector and plug it into HE2 at the mainboard, an...
by Jetguy
Tue May 22, 2018 1:47 pm
Forum: Feature requests, ideas, wishes
Topic: Hardware Suggestion - Filament Clog or Binding Sensing
Replies: 8
Views: 101

Re: Hardware Suggestion - Filament Clog or Binding Sensing

BTW, if you don't know, Toybuilder Labs tried to get that exact filament detector integrated back at the start of this during the Kickstarter.
by Jetguy
Tue May 22, 2018 1:45 pm
Forum: Feature requests, ideas, wishes
Topic: Hardware Suggestion - Filament Clog or Binding Sensing
Replies: 8
Views: 101

Re: Hardware Suggestion - Filament Clog or Binding Sensing

Solution already exists and will integrate with existing Filament detection firmware and pause feature. You could literally plug this in today into the mainboard, load the firmware, and use it at the spools (does NOT need to be at the feeder) and it monitors the filament for movement over time (an a...
by Jetguy
Tue May 22, 2018 1:31 pm
Forum: Printing Settings
Topic: retraction and grinding nightmare!
Replies: 1
Views: 79

Re: retraction and grinding nightmare!

There are about 3-4 different topics all regarding a stock extruder slipping and grinding at various points in a print. They are all related to the same basic guidelines to improve the stock system. http://forum.raise3d.com/viewtopic.php?f=2&p=31048#p31048 Sorry you are having issues, we have so...
by Jetguy
Tue May 22, 2018 1:27 pm
Forum: General
Topic: Not 1 successful print N2+
Replies: 1
Views: 127

Re: Not 1 successful print N2+

Sorry you are having issues, we have solutions to attempt to correct this: Good related topic of another user having basically similar issues (slightly different, but in the end, still grinding/slipping) http://forum.raise3d.com/viewtopic.php?f=4&p=31044&sid=f349c8e14b7903bb77db65640b1d3e25#...
by Jetguy
Mon May 21, 2018 4:11 pm
Forum: General
Topic: Wrong Date and Time
Replies: 11
Views: 1050

Re: Wrong Date and Time

Yes, check periodically the download page for updates for all 3 major products.
Ideamaker version
Raisetouch versions (LCD update on the printer)
Motion control firmware (Marlin)
With pictures:
viewtopic.php?f=3&t=1652&p=13896#p13896
by Jetguy
Mon May 21, 2018 12:44 pm
Forum: Software
Topic: Touchscreen Firmware 0.9.9 Release Note 2018.5.17
Replies: 42
Views: 725

Re: Touchscreen Firmware 0.9.9 Release Note 2018.5.17

Sorry If I have contributed to that confusion. #1 I still believe that in most cases, we are at a point you should attempt to update to the latest version to get all the features and improvements with both firmware version (Raisetouch and Marlin). We are still in the bug fixing and new feature in n...
by Jetguy
Mon May 21, 2018 12:25 pm
Forum: Printing Settings
Topic: Problems with vase mode
Replies: 14
Views: 143

Re: Problems with vase mode

And yes, please share or provide a link to the STL if you can. This will always help any diagnoses when asking about setting or error in slicing.
by Jetguy
Mon May 21, 2018 12:22 pm
Forum: Printing Settings
Topic: Problems with vase mode
Replies: 14
Views: 143

Re: Problems with vase mode

I've printed this exact vase with other slicing software on my printer with no problem. However, this is what I get when I run it through ideaMaker: https://i.imgur.com/fkeQ8oI.jpg Any suggestions? I think is potentially related to a thin wall setting bug in Ideamaker. What happens is, for reasons ...
by Jetguy
Sun May 20, 2018 3:23 pm
Forum: Hardware
Topic: Improvements by using TMC2130 driver.
Replies: 69
Views: 5536

Re: Improvements by using TMC2130 driver.

Again, in one way, what you are comparing is kind of a different topic. When Zemlin used SD5984 drivers, it's more akin to a change of simply not using stealthchop or silent mode. The SD5984 is a very good driver- no doubt about it. It's based on proven and well known functionality. Sometimes simple...

Go to advanced search