Search found 2483 matches

by Jetguy
Fri Jun 22, 2018 10:30 am
Forum: Hardware
Topic: Raise3d Pro2 Review in Deutsch Video
Replies: 5
Views: 38

Re: Raise3d Pro2 Review in Deutsch Video

Watching an alternate video of the Pro2, it may be hard to see, but the extruder fan is spinning in this video while hot and while loading. https://www.youtube.com/watch?v=20qeZe1jDaQ At around 4:20 or so, they are showing the loading process of preheating and then filament extruding and again, whil...
by Jetguy
Fri Jun 22, 2018 10:22 am
Forum: Hardware
Topic: Raise3d Pro2 Review in Deutsch Video
Replies: 5
Views: 38

Re: Raise3d Pro2 Review in Deutsch Video

Again, I would immediately contact support and I suggest you do not attempt to print or heat the system until you get an answer from Raise 3D tech support.
by Jetguy
Fri Jun 22, 2018 10:13 am
Forum: Hardware
Topic: Raise3d Pro2 Review in Deutsch Video
Replies: 5
Views: 38

Re: Raise3d Pro2 Review in Deutsch Video

Again, in the video, we see the screenshot and timestamp the hotends are heating and well above 50C. On the previous N series, the extruder cooling fans were wired to constant on ports (not software/firmware controlled). My understanding is that maybe they enabled the extruder cooling fan to be soft...
by Jetguy
Fri Jun 22, 2018 9:40 am
Forum: Hardware
Topic: Raise3d Pro2 Review in Deutsch Video
Replies: 5
Views: 38

Re: Raise3d Pro2 Review in Deutsch Video

Google translate to German because it's 5AM and my German is not as good as it used to be. Ihr Extruder-Kühlventilator scheint sich nicht zu drehen, während die Extruder erhitzt werden. Der große Lüfter an der Vorderseite kühlt den kritischen Kühlkörper des Hotends, so dass Sie bei Minute 7:54 im Vi...
by Jetguy
Fri Jun 22, 2018 9:38 am
Forum: Hardware
Topic: Raise3d Pro2 Review in Deutsch Video
Replies: 5
Views: 38

Re: Raise3d Pro2 Review in Deutsch Video

And, that printer already has a serious fault out of the box while watching the video. Your extruder cooling fan does not appear to be spinning while extruders are heated. The big fan in the front cools the critical heatsink of the hotend, so at minute 7:54 in the video, you first showed the LCD con...
by Jetguy
Thu Jun 21, 2018 7:11 pm
Forum: Hardware
Topic: half of the touch screen does not work
Replies: 6
Views: 48

Re: half of the touch screen does not work

Again, the only scenario that after grounding your finger and attempting touch that 1/2 the screen responds to no touch, then the overlay may be damaged or the ribbon cable to the back of the LCD itself.
by Jetguy
Thu Jun 21, 2018 6:51 pm
Forum: Software
Topic: travel across print in vase mode
Replies: 7
Views: 38

Re: travel across print in vase mode

Also, link to the STL or share the gcode, but the STL will tell us if it cna even be sliced in vase mode without modifications.
by Jetguy
Thu Jun 21, 2018 6:50 pm
Forum: Software
Topic: travel across print in vase mode
Replies: 7
Views: 38

Re: travel across print in vase mode

See this topic for some vase mode tips.
viewtopic.php?f=3&t=6845&p=27482&hilit=vase+mode#p27256

Also note, there is a quirk with the thin wall settings in Ideamaker that can create spurious points never part of the model.
Vase mode thin wall.jpg
by Jetguy
Thu Jun 21, 2018 6:43 pm
Forum: Software
Topic: travel across print in vase mode
Replies: 7
Views: 38

Re: travel across print in vase mode

Vase mode only works if the object being sliced is not already hollow. Otherwise, it does not slice in vase mode even when vase mode is selected. This is true of most slicers, not just ideamaker.
by Jetguy
Thu Jun 21, 2018 6:41 pm
Forum: Hardware
Topic: half of the touch screen does not work
Replies: 6
Views: 48

Re: half of the touch screen does not work

Just a couple of other notes here: #1 the screen is capacitive touch based, meaning the screen needs your finger to be grounded. Since you wear rubber shoes and the screen sits inside a plastic box, when touches do not register, take your second hand and place it on the printer and touch a metal scr...
by Jetguy
Thu Jun 21, 2018 6:18 pm
Forum: Hardware
Topic: half of the touch screen does not work
Replies: 6
Views: 48

Re: half of the touch screen does not work

That sounds like physical damage to the LCD or a loose cable. The actual LCD display portion is driven via a thin flat ribbon cable, then the touch signal to the board and backlight are driven with a wire style ribbon cable. Technically the same information as the Acadia applies here. The difference...
by Jetguy
Thu Jun 21, 2018 5:02 pm
Forum: Hardware
Topic: Hardened nozzles
Replies: 2
Views: 49

Re: Hardened nozzles

You can also see testing results by others using Ruby nozzles viewtopic.php?f=4&t=1709&p=26106&hilit=ruby#p26106
by Jetguy
Thu Jun 21, 2018 4:58 pm
Forum: Hardware
Topic: Hardened nozzles
Replies: 2
Views: 49

Re: Hardened nozzles

#1 the V2H nozzles are specifically made for the printer by MicroSwiss for Raise3D https://www.raise3d.com/collections/3d-printer-spare-parts/products/hot-end-v2h-nozzle. From the MicroSwiss site backing this up: https://store.micro-swiss.com/collections/raise3d Micro Swiss have cooperated with Rais...
by Jetguy
Thu Jun 21, 2018 2:06 am
Forum: General
Topic: eSUN PVA
Replies: 11
Views: 1793

Re: eSUN PVA

You cannot make filament too dry.
by Jetguy
Thu Jun 21, 2018 1:38 am
Forum: Printing Settings
Topic: Bondtech and 3dsolex nozzles
Replies: 2
Views: 76

Re: Bondtech and 3dsolex nozzles

Again, sorry if I'm not giving the exact answer you wanted, but I can say this, #1 I ordered the same 3D Solex nozzle set for the Raise 3D printer. #2 I'm using a Bondtech extruder on most of my printers, just not the biggest machine running the 3mm filament (that runs a Titan Aero), but I am runnin...
by Jetguy
Wed Jun 20, 2018 6:48 pm
Forum: Printing Settings
Topic: Bondtech and 3dsolex nozzles
Replies: 2
Views: 76

Re: Bondtech and 3dsolex nozzles

Also, I have an ABS profile for a 0.8mm Solex nozzle from Vice Chief that prints OK, but the truth is, we got much better results from S3D with these larger nozzles. This was used on My N2 plus with a Bondtech and normal 1.75mm filament. The slicing settings don't change, the only place where 3mm is...
by Jetguy
Wed Jun 20, 2018 6:42 pm
Forum: Printing Settings
Topic: Bondtech and 3dsolex nozzles
Replies: 2
Views: 76

Re: Bondtech and 3dsolex nozzles

Printing with a 1.5mm 3D Solex, but it's also 3mm filament. I'm not fully dialed in, but getting some insane rates, example being printing 243g of filament in 3hours and 31 minutes. The same print, had I used a 0.4mm nozzle and 0.2mm layer height to get about the same wall thickness (number of shell...
by Jetguy
Wed Jun 20, 2018 2:25 pm
Forum: Software
Topic: Touchscreen Firmware 0.9.11 Release Note 2018.6.14
Replies: 84
Views: 2247

Re: Touchscreen Firmware 0.9.11 Release Note 2018.6.14

OK, so testing 0.9.11, it appears the sort issue discovered around 0.9.10 but may have started in 0.9.9 is now working in 0.9.11. In saying that, it means that by default after updating, sort on the LCD at the printer remains at sort by date uploaded, making your most recent file uploaded first on t...
by Jetguy
Wed Jun 20, 2018 12:37 pm
Forum: Software
Topic: Touchscreen Firmware 0.9.11 Release Note 2018.6.14
Replies: 84
Views: 2247

Re: Touchscreen Firmware 0.9.11 Release Note 2018.6.14

I'm curious how many others are now testing the new latest 0.9.11 update that kind of went out silently since Raise 3D just keeps editing the title of this topic and editing the first post. I really think a new system to announce releases- especially ones that fix known bugs and a better marking of ...
by Jetguy
Tue Jun 19, 2018 8:47 pm
Forum: Hardware
Topic: Pro Series Steel Nozzle
Replies: 2
Views: 44

Re: Pro Series Steel Nozzle

BTW, they are NOT steel nozzles. They are brass nozzles hard coated with an alloy.

Go to advanced search