Official Raise3D Community

my question is, is this a loose cable in the socket or that the JST connectors were not crimped properly? do the wires pull out of the connects would be my question? if the issue is a loose cable in the socket, i would try removing the first link cover of the cable chain. I did that on my N2 and I h...

researching the issue on marlin firmware, it was a bug a long time ago. likely the issue now is that your PID is off and needs to be configured. the issue had to due with temperature set where the printer was stabled. then when it was allowed to fall out of stable temperature and restarted, it cause...

PVA requires very slow print speed, it also starts going bad as soon as you open it I have been told. As an alternative, you could try PVB. It is called Polysmooth and is sold by Polymaker. It is soluble in Isopropyl alcohol. I'm about to pull the second extruder off my N2 cause dual extrusion cause...

if the connection is dropping, you need to go into the touchscreen and limit it to 100mps and it should function better. I know after I did that I am getting faster and more stable uploads to the printer from ideamaker.

if you have the new cable part installed between the cable and the main board, it should be reporting a thermal runaway if the ribbon cable has failed. I have not had my ribbon cable fail on my kickstarter printer. I have rewired some things on my printer but not that cable. This leads me to suspect...

further proof that the vref on those steppers is set to high and raise3d needs to modify the closed firmware on the pro2 series to fix this issue.

It was later discovered that it was possible for a thermal runaway to happen on the printer if the ribbon cable becomes disconnected or damaged. raise3d created a new part to detect this issue.

I don't know if he solved his issue.

zemlin wrote:

firesped wrote:I wonder though, is raise3d going to give a better deal then just buying direct from bondtech for those parts?

If their buildtak pricing is any indication ...

I haven't paid attention to buildtak pricing. I just print straight on glass with no buildtak on it. (either side)

I wonder though, is raise3d going to give a better deal then just buying direct from bondtech for those parts?

just keep in mind, that you will lose build height from using this. I've had good results using the E3D V6 on my N2 with the adapter that was made for it. I don't know how much difference there is in the hotend interface between the N series and the Pro series though. The adapter is shorter then the...

has anyone come up with a front mounted fan for cold end cooling that includes the berd air max mounts?

on my original bondtech upgrade. I had unknowingly set the vref wrong. It was twice what it was supposed to be due to how the vref on the steppers I was using works. This combined with a hot summer day, caused this issue to happen to me, where low temp plastic metled inside the bondtech casing. I pr...

this is caused by 1 factor. the filament is getting too soft in the bondtech extruder and melting. 2 things can cause this. #1 voltage is too high on the stepper drivers for the stepper motors on the extruder. extra heat is transferred into the gears pushing the filament, causing it to soften and me...

my opinion of PVA. filament of dreams. in order to use it, you need to print extremely slowly for everything because the PVA does not react well to fast movements. so even if you are not printing it, the other material can knock it loose from the printer causing everything to fail. I tried it once a...

when I had my first bondtech on my N@ and did not have my steppers calibrated correctly. i had filament melting inside the housing for the bondtech because the motors were getting too hot causing the gears to be too hot. i had to print new housings and remount all the hardware when they were damaged...

just to point out. unless you mod your printer like I have mine. you are pulling hot air from inside the printer to cool your print. even with my mod, I'm not sure if it fully prevents the outside edges from heating. likely you want to mount the pump outside of the enclosure to pull colder air in. I...

I was still on 9.7, I was trying to upload a file from my computer to the printer and it was timing out. so I updated to this in hopes that it A) does not break my firmware. and B) fixes the uploading issue. That said, a feature to be able to move gcode from USB plugged into the touchscreen to the o...

Given that the security is way out of date on the pcDuino and no way to update it. someone could probably hack their way into your printer and do something else with it.

I had run bowden tubes in these early. what I did was took the larger tubes that came with it and cut open a side so I could run the smaller tube into the larger tube.

I noticed that when I went to the current fan design, my print quality went way up but the issue I have is that I don't have the air blowing on the print from the reverse side. I saw the Berd-Air posted before and wasn't sure of the price. but it may be that the price has come down now and is afford...