Search found 26 matches

by Behold
Mon Apr 16, 2018 3:17 pm
Forum: General
Topic: Connect to printer remotely?
Replies: 7
Views: 1432

Re: Connect to printer remotely?

I was able to get this to work on a network that uses IPv4 protocol. How do we do this with IPv6 addresses for public IP?
by Behold
Fri Mar 16, 2018 12:47 pm
Forum: Hardware
Topic: Can't use full build volume of the N2+
Replies: 14
Views: 1479

Re: Can't use full build volume of the N2+

What did you find out about the issue? Was it raft related?
by Behold
Sat Feb 24, 2018 4:05 pm
Forum: Hardware
Topic: Motor driver position and orientation.
Replies: 10
Views: 233

Re: Motor driver position and orientation.

Jetguy wrote:Please ensure you get it right, the X and Y are different drivers and are "backwards" to the A4988 drivers used in the extruder positions and Z axis.


Ok, I see.
by Behold
Sat Feb 24, 2018 4:00 pm
Forum: Hardware
Topic: Motor driver position and orientation.
Replies: 10
Views: 233

Re: Motor driver position and orientation.

No, the black ones are your XY and your green ones are A4988s and XYZ drivers. So yes, there is absolutely a chance if you didn't know that, made some really bad assumptions and plugged them in wrong, you just blew up the drivers and the mainboard and that's why you have a serial error. This is con...
by Behold
Sat Feb 24, 2018 3:55 pm
Forum: Hardware
Topic: Motor driver position and orientation.
Replies: 10
Views: 233

Re: Motor driver position and orientation.

Support on these machines are absolutely terrible. I received a board with no documentation. I took before images but I guess the contrast in the images are not good enough to differentiate.
by Behold
Sat Feb 24, 2018 3:51 pm
Forum: Hardware
Topic: Motor driver position and orientation.
Replies: 10
Views: 233

Re: Motor driver position and orientation.

Is there a place that's documented?
by Behold
Sat Feb 24, 2018 3:50 pm
Forum: Hardware
Topic: Motor driver position and orientation.
Replies: 10
Views: 233

Re: Motor driver position and orientation.

Super
by Behold
Sat Feb 24, 2018 2:29 pm
Forum: Hardware
Topic: Motor driver position and orientation.
Replies: 10
Views: 233

Re: Motor driver position and orientation.

Unfortunately, none of my driver's look like that. I have two black ones and three green ones. I'm assuming the black ones are extruder drivers since I have dual extruders. But the green driver boards are identical. I saw those threads and tried to use them as reference but I am getting serial conne...
by Behold
Sat Feb 24, 2018 5:21 am
Forum: Hardware
Topic: Motor driver position and orientation.
Replies: 10
Views: 233

Motor driver position and orientation.

Is there a proper diagram that shows motor driver orientation? Better yet is there a proper diagram that shows all the correct connections for the mainboard?

Wish I can print with this thing.
by Behold
Tue Feb 06, 2018 2:03 pm
Forum: Hardware
Topic: spark then ramping heat
Replies: 8
Views: 255

Re: spark then ramping heat

It's shorted to the body for sure.

There are sparks coming from the back of the extruder by the thermistors and the heat cartridges. I believe that's the source.

I thought the spark was an indication of something blowing but it's a temp connection
by Behold
Tue Feb 06, 2018 1:26 pm
Forum: Hardware
Topic: spark then ramping heat
Replies: 8
Views: 255

Re: spark then ramping heat

In any regard, when the heaters are unplugged at the side break out board the system reports that it is at room temperature and the temperature does not runaway.

It seems like the heater is either shorted to the body some where or the mosfet blew.

Where is the main board mosfet located?
by Behold
Tue Feb 06, 2018 1:02 pm
Forum: Hardware
Topic: spark then ramping heat
Replies: 8
Views: 255

Re: spark then ramping heat

I should post the ticket thread.
by Behold
Tue Feb 06, 2018 12:51 pm
Forum: Hardware
Topic: spark then ramping heat
Replies: 8
Views: 255

Re: spark then ramping heat

I didn't see your question because I was waiting for an answer to my problem. Plus, I told you that the problem was intermittent. I stated several times in the ticket thread. But tech support had me send them an image and said they were waiting to talk to their head tech. I am confused why they woul...
by Behold
Mon Feb 05, 2018 10:34 pm
Forum: Hardware
Topic: Broken ribbon… again… I think
Replies: 28
Views: 1049

Re: Broken ribbon… again… I think

Thank you. I appreciate your response
by Behold
Mon Feb 05, 2018 8:28 pm
Forum: Hardware
Topic: spark then ramping heat
Replies: 8
Views: 255

Re: spark then ramping heat

I believe that I am getting accurate heat measurements from the thermistor. I'll verify and report back. Thanks jetguy
by Behold
Mon Feb 05, 2018 5:32 pm
Forum: Hardware
Topic: Broken ribbon… again… I think
Replies: 28
Views: 1049

Re: Broken ribbon… again… I think

I want to make sure this is correct... the filament run out sensor is that "safety board"?! @jetguy was talking about?
by Behold
Mon Feb 05, 2018 5:08 pm
Forum: Hardware
Topic: spark then ramping heat
Replies: 8
Views: 255

spark then ramping heat

There was a spark on my Raise3D N2 Plus dual near the extruder then the heat just kept on ramping until it hovered around 300c. Now every time I turn the machine on the heat on the left extruder just ramps up without any input from me. Please help. I also have a support ticket but my last still rema...
by Behold
Tue Dec 12, 2017 3:48 am
Forum: General
Topic: resuming failed print
Replies: 9
Views: 435

Re: resuming failed print

I'll have to test it on a non critical print... I just haven't had those yet ;)
by Behold
Mon Dec 11, 2017 12:48 pm
Forum: General
Topic: resuming failed print
Replies: 9
Views: 435

Re: resuming failed print

Ok, I upgraded yesterday.
by Behold
Sun Dec 10, 2017 3:07 pm
Forum: General
Topic: resuming failed print
Replies: 9
Views: 435

Re: resuming failed print

What's your projected release date for the new firmware?

Go to advanced search