Search found 96 matches

by Squenz
Fri Feb 16, 2018 2:36 pm
Forum: Printing Settings
Topic: PETG Settings
Replies: 27
Views: 268

Re: PETG Settings

As i said, i print on a white 1mm PEI/Aluminium Plate. Works just fine with ABS and almost everything else, never had an issue. I use the clamps as they came with the printer and similiar.
by Squenz
Thu Feb 15, 2018 11:11 pm
Forum: Feature requests, ideas, wishes
Topic: Clips for the glass plate that Never interfere with the nozzle
Replies: 3
Views: 76

Re: Clips for the glass plate that Never interfere with the nozzle

Or you just place them just around the corner on the left and right edges of the build plate ?

If you feel more comfortable having one at the front edge also, just place that one a tad right of the middle ?
by Squenz
Thu Feb 15, 2018 4:10 pm
Forum: Hardware
Topic: N1 Upgrade
Replies: 10
Views: 172

Re: N1 Upgrade

A pic won't show much of this upgrade, one can barely see the actual parts, because i printed everything in silver/light gray ABS. The bucket disappears nearly complete behind the big z-axis bracket. I'll see if i can snap a pic viewing from the top after homing z-axis.
by Squenz
Thu Feb 15, 2018 2:24 pm
Forum: Printing Settings
Topic: PETG Settings
Replies: 27
Views: 268

Re: PETG Settings

Excuse my Ignorance, but why do i want to stick PEI onto glass ? Yes, i get the fact the glass is a stable, rigid and a good flat surface to print on, but, on the other hand, i print directly on a 1mm PEI sheet sitting on the Aluminium bed. When the print is finished and i'm around, i just unclip th...
by Squenz
Thu Feb 15, 2018 10:42 am
Forum: Software
Topic: Feature request for internal support or infill when needed.
Replies: 12
Views: 176

Re: Feature request for internal support or infill when needed.

I don't know if my findings qualify as a feature, but i saw the other day, when printing the kobayashi maru fidget cube (found on thingiverse), the Infill is not created by looking at each individual part of this cube, but it is a global pattern which seem to be layed across the outer boundaries and...
by Squenz
Wed Feb 14, 2018 10:53 pm
Forum: Printing Settings
Topic: PETG Settings
Replies: 27
Views: 268

Re: PETG Settings

by Squenz
Wed Feb 14, 2018 10:38 pm
Forum: Printing Settings
Topic: PETG Settings
Replies: 27
Views: 268

Re: PETG Settings

As is read in another the other day, Ideamaker uses Z 0,5 mm for the first layer of the Raft.

One could come to the conclusion, if your print doesn't hold with 0,3, but the Raft (if you use Ideamaker) sticks at 0,5mm, you're raftless print starts too close ...
by Squenz
Wed Feb 14, 2018 10:13 pm
Forum: Software
Topic: New Acceleration and Jerk settings
Replies: 12
Views: 148

Re: New Acceleration and Jerk settings

Ideamaker also allows to adjust several Acc- and Jerk settings in the current version.
by Squenz
Wed Feb 14, 2018 10:12 pm
Forum: Printing Settings
Topic: PETG Settings
Replies: 27
Views: 268

Re: PETG Settings

So, you actual distance between nozzle and surface is 0,15 mm ? Sounds a bit close for me, but if you can make it happen with a Raft, hey, whatever it takes ... Garolite is the the "go-to" surface for Nylon. Markforged uses this as standard print surface and it obviously works. Garolite is...
by Squenz
Wed Feb 14, 2018 9:45 pm
Forum: Printing Settings
Topic: PETG Settings
Replies: 27
Views: 268

Re: PETG Settings

Raess wrote:...
My last settings is
Z offset -0.150 (BLTouch)
..



Does Z- 0.150 mean you're printing at an absolute distance of standard 0.2-0.15 = 0.05 mm between nozzle and build plate ?
by Squenz
Wed Feb 14, 2018 9:41 pm
Forum: Printing Settings
Topic: PETG Settings
Replies: 27
Views: 268

Re: PETG Settings

Maybe a different build plate ? I.e. i wanted to try printing PA12 Nylon. I read it should work with the BuildTak, but i had no luck. Garolite should work fine they said, but i couldn't get it at the time. So, i walked into the next hardware store and looked out for something to print on. I came out...
by Squenz
Wed Feb 14, 2018 9:19 pm
Forum: Hardware
Topic: N1 Upgrade
Replies: 10
Views: 172

Re: N1 Upgrade

Ok, i promised i'll bring something in here.... I was pondering about a solution for my ideas for quite some time, question was, how can i quick change the build surface from, say stock BuildTak on Glass to say, 1mm PEI or 0,4 Garolite, or plain glass without touching any of the carefully adjusted b...
by Squenz
Wed Feb 14, 2018 8:33 pm
Forum: Software
Topic: New Acceleration and Jerk settings
Replies: 12
Views: 148

Re: New Acceleration and Jerk settings

Or do I have to calibrate the values? And if so how? It's not the sort of thing that has one right answer. Speed, acceleration, and jerk have a big impact on build times, part quality and appearance. You need to find the balance point for your prints and what's most important to you. For me it's be...
by Squenz
Wed Feb 14, 2018 4:17 pm
Forum: Feature requests, ideas, wishes
Topic: Feature Request: faster way to position extruders manually
Replies: 5
Views: 62

Re: Feature Request: faster way to position extruders manually

Mine is a bit the same. Try pressing the button a bit above the your target area, maybe 6 or 8 pixels, and it works most of the time.

There was a request for Screen Calibration here, didn't come with last Displayfrimware-Update.
by Squenz
Wed Feb 14, 2018 7:32 am
Forum: Software
Topic: Ideamaker G code generation for CR10-S
Replies: 4
Views: 77

Re: Ideamaker G code generation for CR10-S

... If i manually set it to 0.05 after the gcode is generated, my print sticks like glue.. Is there any way to avoid the manual change i need to make during Gcode generation? .... I just came to my mind, if you're using Ideamaker exclusive with your printer, just adjust general bed height closer to...
by Squenz
Tue Feb 13, 2018 9:14 pm
Forum: User's Gallery
Topic: Fan Mod (Extra Gcode Controlled Fan)
Replies: 8
Views: 132

Re: Fan Mod (Extra Gcode Controlled Fan)

Hey thanks, i was looking into a parts cooling fan for quite some time. I even copied and printed out one version from thingverse nut realized, this rear mounted option won't work on my N1. I use EBM Pabst Fans with very good results. They're not cheap at all, but when it's a sound-sensitive environ...
by Squenz
Mon Feb 12, 2018 4:27 pm
Forum: General
Topic: Printer failure
Replies: 41
Views: 532

Re: Printer failure

I definately won't make this for others, as i hate this kind of job and it's a liabiliy issue for me to top it off. But i could send you a set of parts, and as much cable as you need for your N1/N2/N2+, but shipping to Sweden could be a killer, don't know how much that would cost. The only real prob...
by Squenz
Mon Feb 12, 2018 3:42 pm
Forum: General
Topic: Thicker glass bed... questions and thoughts.
Replies: 12
Views: 145

Re: Thicker glass bed... questions and thoughts.

Oh, Ok, i print on a 1mm PEI plate and plan on using 0.4 mm Tufnol Whale when i start printing PA12 Nylon. I never had the need of such a extreme flatness, makes no sense in book, because any technical stuff you push through the extruder warps somewhat during printing and facing this ugly face when ...
by Squenz
Mon Feb 12, 2018 3:27 pm
Forum: General
Topic: Printer failure
Replies: 41
Views: 532

Re: Printer failure

Of course i'll bring in the resistors. Easy peasy thing with Jetguy's advise. We all can't thank him enough for all he did and still does. Other parts ? Well, i ordered the connector and pins from RS Online, the cable from IGUS, they both have everything in stock and it looks like things will come i...
by Squenz
Mon Feb 12, 2018 3:01 pm
Forum: General
Topic: Thicker glass bed... questions and thoughts.
Replies: 12
Views: 145

Re: Thicker glass bed... questions and thoughts.

Well, o gotta ask, increased stiffness ? Why would that be necessary ?

Go to advanced search