Search found 9 matches

by allergictotrees
Sat Feb 25, 2017 12:41 am
Forum: Printing Settings
Topic: Makerbot ABS/PLA
Replies: 2
Views: 1245

Re: Makerbot ABS/PLA

thank you for the info!
by allergictotrees
Wed Feb 22, 2017 9:15 pm
Forum: Printing Settings
Topic: Makerbot ABS/PLA
Replies: 2
Views: 1245

Makerbot ABS/PLA

Can someone share Extruder and Bed temp settings for Makerbot ABS and PLA? I have a dozen rolls from my previous printer (rep2x) that I would like to use on my N2+.

thanks!
by allergictotrees
Tue Jan 24, 2017 5:42 am
Forum: Feature requests, ideas, wishes
Topic: Filament Monitor / Auto Pause Feature
Replies: 10
Views: 3160

Re: Filament Monitor / Auto Pause Feature

for printers with Dual extruders it would be great to have the printer switch to the second extruder when the filament monitor detects low/no filament.
by allergictotrees
Wed Jan 18, 2017 5:28 pm
Forum: Hardware
Topic: Day 1: Board error: Error 1: Extruder switched off. MINT...
Replies: 28
Views: 5085

Re: Day 1: Board error: Error 1: Extruder switched off. MINT...

wires were/are looped and secure. I did in fact unscrew them all the way out to make sure that I could seat them in between the clip as instructed by Raise3D support. The error on the display changed from an error1 to an error0 which led them to believe it is a defective cable.
by allergictotrees
Tue Jan 17, 2017 7:30 pm
Forum: Hardware
Topic: Day 1: Board error: Error 1: Extruder switched off. MINT...
Replies: 28
Views: 5085

Re: Day 1: Board error: Error 1: Extruder switched off. MINT...

thanks for the feedback Jetguy. it turns out that the thermocoupler wire is defective and they are sending a replacement. I have had a makerbot rep2x for the past couple years that has been in the same garage/workshop and I've been successfull in printing small and large (bb8) projects. But I hear y...
by allergictotrees
Sun Jan 15, 2017 4:18 pm
Forum: Hardware
Topic: Day 1: Board error: Error 1: Extruder switched off. MINT...
Replies: 28
Views: 5085

Re: Day 1: Board error: Error 1: Extruder switched off. MINT...

ok, so the problem is BACK :( . I'm wondering if the room temperature has something to do with the issue. I keep the printer in my garage/workshop that can get cold (currently 48 degrees F). Will the ambient temperature of the room affect the printer? I have a Makerbot Replicator 2X and have never h...
by allergictotrees
Sat Jan 14, 2017 5:31 pm
Forum: Hardware
Topic: Day 1: Board error: Error 1: Extruder switched off. MINT...
Replies: 28
Views: 5085

Re: Day 1: Board error: Error 1: Extruder switched off. MINT...

UPDATE: Printer is working again! I retightened both ends of the cable, the one in the box at the bottom was glued in but pressed it in to be sure. Took apart the housing (with the logo) and retightened the screws behind it. Not sure which was one the problem but I'm back at the print screen. Thanks...
by allergictotrees
Sat Jan 14, 2017 3:57 pm
Forum: Hardware
Topic: Day 1: Board error: Error 1: Extruder switched off. MINT...
Replies: 28
Views: 5085

Re: Day 1: Board error: Error 1: Extruder switched off. MINT...

Wow, thanks for the very detailed overview of the system and the possible solutions Jetguy and Vicky! I will check these out and report back. thanks again!
by allergictotrees
Sat Jan 14, 2017 2:50 am
Forum: Hardware
Topic: Day 1: Board error: Error 1: Extruder switched off. MINT...
Replies: 28
Views: 5085

Day 1: Board error: Error 1: Extruder switched off. MINT...

I just received my N2+ and was able to print a benchy in PLA. Later that night I get this error on the display: "Board error: Error:1: Extruder switched off. MINT...". After pressing Restart I get the same message. I've also restarted using the manual switch behind the control panel, same ...

Go to advanced search